User's Manual

ManualsBrandsInteractive Technologies ManualsElectronicsMarine Device Remote Control Transmitter

• Operating Instructions

Please read before using this equipment.

Marine Remote Commander System

MC10



1-1-8 Nishi Gotanda

Shinagawa-ku

Tokyo 141-0031, Japan

Phone 03-5496-8231



19145 Gramercy Place

Torrance, California 90501 U.S.A.

Phone 1-800-ALPINE-1 (1-800-257-4631)



777 Supertest Road Toronto

Ontario M3J 2M9, Canada

Phone 1-800-ALPINE-1 (1-800-257-4631)



161-165 Princess Highway, Hallam

Victoria 3803, Australia

Phone 03-8787-1200



Wilhelm-Wagenfeld-Str. 1-3 80807 München, Germany

Phone 089-32 42 640



ALPINE House

Fletchamstead Highway, Coventry CCV4 9TW, U.K.

Phone 0870-33 33 763



(RCS PONTOISE B 338 101 280)

98, Rue de la Belle Etoile, Z.I. paris Nord II,

B.P. 50016, 95945 Roissy Charles de Gaulle

Cedex, France

Phone 01-48638989



Viale C. Colombo 8, 20090 Trezzano

Sul Naviglio (MI), Italy

Phone 02-484781



Portal de Gamarra 36, Pabellón, 32

01013 Vitoria (Alava)-APDO 133, Spain

Phone 945-283588



Leuvensesteenweg 510-B6,

1930 Zaventem, Belgium

Phone 02-725 1315

Printed in China

Summary of content (8 pages)

PAGE 1
Marine Remote Commander System MC10 • Operating Instructions Please read before using this equipment. ALPINE ELECTRONICS MARKETING, INC. ALPINE electronics of u.k., ltd. 1-1-8 Nishi Gotanda Shinagawa-ku Tokyo 141-0031, Japan Phone 03-5496-8231 ALPINE House Fletchamstead Highway, Coventry CCV4 9TW, U.K. Phone 0870-33 33 763 ALPINE Electronics of America, inc. (RCS PONTOISE B 338 101 280) 98, Rue de la Belle Etoile, Z.I. paris Nord II, B.P.
PAGE 2
Operating Instructions WARNING CAUTION This symbol means important instructions. Failure to heed them can result in injury or material property damage. WARNING This symbol means important instructions. Failure to heed them can result in serious injury or death. HALT USE IMMEDIATELY IF A PROBLEM APPEARS. Failure to do so may cause personal injury or damage to the product. Return it to your authorized Alpine dealer or the nearest Alpine Service Center for replacing.
PAGE 3
Basic Operation Basic Operation Basic Operation Installation Installation MC10 Display Unit Optional RUE-M1RF Optional Add-on Commander 333MHz Wireless 2.4GHz Wireless GND GND MC1 +12V 2.
PAGE 4
Program Menu MC10 Display unit Enter Program Mode Program Menu Options 1. ID NUMBER This is the serial number of the display unit. * Range of serial numbers: 00001 to 99999 2. RF STRENGTH Signal strength between a display unit and the closest display or transceiver unit in the MC10 wireless system * Range of strength: [ ] to 3. SIGNAL STATUS Wireless signal connection status between a display unit and the transceiver unit * Values: [CONNECTED, NO CONNECT] 4.
PAGE 5
Program Mode Example 1. Enter Program Mode 4. Press VOL + or VOL – to adjust the current CONTRAST value 2. Press VOL + or VOL – until CONTRAST shows on top line of display 5. Press ENT to save new CONTRAST value 3. Press ENT to program new CONTRAST value 6.
PAGE 6
MC1 Add-on Commander Pairing Procedure 1. Power on existing MC10 system 2. Connect power and ground wires of MC1 add-on commander (see Installation) 3. MC1 add-on commander display will turn on and automatically go to the pairing screen in the program menu with ADD MC1 showing on the display ADD MC1 MC1 Paring Screen 4. On marine radio, select FM Tuner as source (make sure that tuner seek mode is DX or LOCAL , not MANUAL) 5.
PAGE 7
Mesh Network Operation Mesh Network OFF Transceiver 2.4GHz Wireless APN Marine Head Unit MC10 Marine Commander System Mesh Network OFF Transceiver 2.4GHz Wireless 2.
PAGE 8
Mesh Network Operation To install an MC1 Add-on Commander in a new location that is outside the MC10 system range: 1. Go to the MC10 system display unit that is closest to the new location 2. Turn Mesh Network ON in the program menu, then exit program menu 3. Follow the MC1 Add-on Commander Pairing Procedure on page 6 to complete the new installation * When MESH NET is turned ON in the program menu of a display unit, it becomes a signal repeater for extending the MC10 system range.