CONFIDENTIAL IS-CTR-DEBUGGER Set-up Manual INTELLIGENT SYSTEMS CO.,LTD.
IS-CTR-BOX Set-up Manual CONFIDENTIAL Packing List Packing List IS-CTR-BOX 1 CTR for EMULATOR 1 INTELLIGENT SYSTEMS Development Kit for CTR (CD-ROM) 1 CTR for EMULATOR Cable 1 AC Adapter (RVL-002) 1 USB Cable 1 Nintendo 3DS Stylus (in the CTR for EMULATOR) 1 IS-CTR-BOX screw type stand (with two screws) 1 Ferrite Core (made by SEIWA ELECTRIC MFG. CO.,LTD.) 2 Hardware Software Accessories Version 0.0.
IS-CTR-BOX Set-up Manual CONFIDENTIAL Using This Product Safely Regulatory Statement This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
IS-CTR-BOX Set-up Manual CONFIDENTIAL Special Notes Notes Note the following when using IS-CTR-DEBUGGER Do not turn off the IS-CTR-BOX device during firmware updates. The IS-CTR-BOX device may not function properly afterward. During use, do not do anything that would prevent heat dissipation, such as blocking the IS-CTR-BOX airflow vent, placing the IS-CTR-BOX in a closed container, or placing objects on top of the IS-CTR-BOX. Connect the CTR for EMULATOR to IS-CTR-BOX.
IS-CTR-BOX Set-up Manual CONFIDENTIAL Operation Environment Requirements The following components are required to operate the IS-CTR-DEBUGGER by connecting it to a computer.
IS-CTR-BOX Set-up Manual CONFIDENTIAL Set-up Installing the Software To install IS-CTR Software Package onto a computer: Note: IS-CTR Software Package include following software IS-CTR-MONO WRITER IS-CTR-EMULATOR IS-CTR-DEBUGGER 1. 2. 3. 4. Log on Windows as a user with an Administrator account on the computer. Exit all currently running programs. "INTELLIGENT SYSTEMS Development Kit for CTR" CD-ROM Please insert the CD-ROM drive.
IS-CTR-BOX Set-up Manual CONFIDENTIAL Installing the IS-CTR-BOX screw type stand Follow the instructions below to installing the IS-CTR-BOX screw type stand 1. Attach the stand to the bottom of the IS-CTR-BOX. Attach the Ferrite Core Follow the instructions below to attach the Ferrite Core 2. Attach a ferrite core to the USB cable. Two loops the cable approximately 5 cm from the USB-B connector and sandwich the portion of the cable that is overlapped with the ferrite core (see the figure at right). 3.
IS-CTR-BOX Set-up Manual CONFIDENTIAL Connections Follow the instructions below to set-up the IS-CTR-BOX 4. Check that the IS-CTR-BOX’s power switch is off. 5. Connect the CTR for EMULATOR to IS-CTR-BOX. Connect the plug with the green band to the IS-CTR-BOX and the plug with the black band to the CTR for EMULATOR. Be sure to tighten the connector screws. 6. Connect the IS-CTR-BOX to the computer with a USB cable. Version 0.0.
IS-CTR-BOX Set-up Manual CONFIDENTIAL 7. Connect the DC plug of the AC adapter to the DC connector on the rear panel of the IS-CTR-BOX. 8. Connect the AC plug of the AC adapter to an outlet. Version 0.0.
IS-CTR-BOX Set-up Manual CONFIDENTIAL Turning the Power On and Off Always use the following procedure to turn the power on. 1. Turn on the power switch on the rear panel of the IS-CTR-BOX. 2. The PWR and SYS lights on the front panel of the IS-CTR-BOX illuminate as follows. I. The PWR light briefly illuminates red. II. The PWR and SYS lights illuminate green. III. The SYS light goes out after a few seconds. 3.
IS-CTR-BOX Set-up Manual CONFIDENTIAL Installing Device Drivers Device drivers must be installed when first connecting the IS-CTR-BOX to a computer or when first connecting to a different USB port. (For Windows XP) 1. Before you connect the IS-CTR-BOX hardware, please install IS-CTR Software Package. 2. When the IS-CTR-BOX hardware is turned on, the Found New Hardware Wizard starts and displays a dialog box that prompts for the installation of a device driver.
IS-CTR-BOX Set-up Manual CONFIDENTIAL 4. Please wait. When the software install begins, the dialog box in Figure C appears. Figure C: Found New Hardware Wizard: Installation Dialog Box 5. The dialog box in Figure D appears during installation. Click Continue Anyway to continue installation. Figure D: Found New Hardware Wizard: Compatibility Dialog Box 6. When the Found New Hardware Wizard completes installation normally, the dialog box in Figure E appears. Click Finish to close the wizard.
IS-CTR-BOX Set-up Manual CONFIDENTIAL (For Windows 7 or Windows Vista) Device drivers are also installed automatically during IS-CTR Software Package installation. Version 0.0.
IS-CTR-BOX Set-up Manual CONFIDENTIAL INTELLIGENT SYSTEMS CO.,LTD. Copyright Ⓒ 2011 INTELLIGENT SYSTEMS CO.,LTD. All rights reserved. The copyrights for the product are held by INTELLIGENT SYSTEMS CO.,LTD. The specifications and content in the manuals or help for this product may change in the future without notice. The software, manual, or help for this product cannot be copied or duplicated in whole or in part without the prior approval of INTELLIGENT SYSTEMS CO.,LTD.
