s6HD Installation and Operation Manual Document Number: 2014KO-UM0211-V2_0
Intellian Satellite TV Antenna Systems Intellian s6HD Serial Number This serial number will be requested for all troubleshooting or service Inquiries. Notice All Rights Reserved Intellian s6HD® and Intellian® are the registered trademarks of Intellian Technologies, Inc., and should not be appropriated without permission by Intellian Technologies, Inc., and the information contained in this manual is the property of Intellian Technologies, Inc.
Table of Contents INTRODUCTION INTRODUCTION TO INTELLIAN s6HD FEATURES OF INTELLIAN s6HD BASIC SYSTEM CONFIGURATION OF INTELLIAN 4 4 5 6 INSTALLATION SYSTEM COMPONENTS TOOLS REQUIRED FOR INSTALLATION PLANNING THE INSTALLATION INSTALLATION AND MOUNTING OF ANTENNA 7 7 10 11 13 INSTALLING THE ACU ACU DIMENSIONS SELECTION OF INSTALLATION SITE CONNECTING THE SYSTEM TO A GPS DC OUT PORT PC TO ACU COMMUNICATION SETUP 16 16 17 23 24 24 OPERATION INSTRUCTION INTRODUCTION 26 26 OPERATING THE ACU ACU SOFT KEY
Intellian Satellite TV Antenna Systems Introduction Introduction to Intellian s6HD Intellian s6HD is a digital marine satellite antenna system specially designed for the DIRECTV services for all types of vessels (Anchored or in transit) to automatically identify, track and capture satellite signals from the Digital Video Broadcasting (DVB: the international standard for digital TV transmissions) compatible Satellites.
Features of Intellian s6HD Simultaneous reception of 3 DIRECTV satellites Intellian s6HD receives HDTV channels from 3 primary DIRECTV’s Ka-band and Ku-band satellites located at 99°W, 101°W and 103°W. No delay time or changing the satellite signal, you can simultaneously watch every DIRECTV channels. Plug and play, DIRECTV capable Intellian s6HD uses single cable from the antenna to ACU for simple installation.
Intellian Satellite TV Antenna Systems Basic System Configuration For your satellite TV system to function properly, the system will have to be connected with all of the provided components as shown in the figure below (Refer to the next chapter ‘Installation’ in this manual for more detailed connection instructions). Separate purchase of a satellite receiver and a TV is required.
Installation The components of the Intellian s6HD are designed as module system so that it is suitable for simple installation on all types of vessels. System Components Antenna Unit The antenna of Intellian s6HD is composed with the following components for optimum search and reception of the satellite signal. • Mechanical Unit – manipulates the antenna to receive the optimal satellite signal regardless of the movement of the vessel. • Control Unit – controls mechanical operation of the antenna.
Intellian Satellite TV Antenna Systems Antenna Control Unit (ACU) The Antenna Control Unit (ACU) provides the power to the antenna and controls the various settings of the antenna. The digital VFD (Vacuum Fluorescent Display) allows for easy operation of the ACU, even in the dark.
Installation Kit Contains the items required for securing the antenna unit and ACU to the vessel. Antenna Item Hex.Bolt Qty Hex.Head Wrench Bolt 5 5 Flat Washer Spring Washer 5 5 Hex. Nut 5 - ACU Item 4 Power Cable 33ft (10m) 1 5 PC Serial Cable 6ft (1.
Intellian Satellite TV Antenna Systems Tools Required for Installation Power Drill 11 mm Spanner 10 mm Drill Bit Pencil Cross-Head Screwdriver 13 mm Spanner Ø80 mm Hole Saw 5 mm Allen/Hex key Figure 06 : Required Tools for Installation 10
Planning the Installation Antenna Unit Install the antenna in accordance with the following procedures to insure maximum performance of the antenna. The antenna should be installed in the place where is an all round clear view of the horizon. Please be sure there are no obstacles within 15 degrees above the antenna. Any obstacles can prevent the antenna from tracking the satellite signal (Refer to the drawing).
Intellian Satellite TV Antenna Systems Cables Before installing the system cables, consider the following points. • All cables need to be well clamped and protected from physical damage and exposure to heat and humidity. • Cables with severe bends are not allowed. • Where a cable passes through an exposed bulkhead or deckhead, a watertight grommet or swan neck tube should be used. Power Requirements You need to follow the power requirements to avoid damage the system.
Installation and Mounting of Antenna The method of installation and mounting of antenna may vary due to vessel design but the following procedures are applicable in most situations, and will result in a secure and effective installation. 72 cm (28.3”) Confirmation of Size Prior to Installation • Check the height and diameter of the bottom surface of the antenna before installing. • The space must be sufficient for installing the antenna unit considering the height and diameter of the antenna.
Intellian Satellite TV Antenna Systems Mark of the Antenna Mounting Position Referring to the mounting template, mark where the antenna is to be mounted on a ship (it must be a flat surface) or on a separate power tower by drawing a square of 30.4cm (12”). 30.4 cm (12”) Note: If a power tower is not suitable to mount the antenna, separate cable shock and waterproofing measures must be taken to protect the RF connector from being exposed to the sea water and external shocks.
Securing Holes for Bolts and Cable Way Make 4 bolt holes of 10mm diameter, one at each corner of a rectangle drawn as below, and make a circular hole of 80mm diameter at the center of the rectangle through which the cable will run. Connection of the Cable Remove the rubber cap from RF connector. Connect the RF cable to the RF connector under the base plate through the access hole using an 11mm spanner. Be careful not to over tighten, as you may damage the connector.
Intellian Satellite TV Antenna Systems Installing the ACU Mounting the Antenna Attach the antenna by using the hex head bolts (M8X50L), M8 spring washers, and M8 flat washers supplied. ACU Dimensions 21.7cm(8.5”) Antenna Unit Support 18.5cm (7.3”) 22.8cm(9”) Deck M8 Flat Washer M8 Spring Washer M8 Hex. Bolt 13mm Spanner 17.8 cm (7”) 7.5 cm (2.95”) Figure 12 : Mounting the Antenna 5.4cm (2.1”) 17.
Selection of Installation Site The ACU should be installed below deck, in a location that is: • Dry, cool, and ventilated. • Easy access from your main TV viewing area. ACU Installation 1. The ACU should be installed using the two supplied mounting brackets which allow for a top or bottom mounting configuration. 2. Using the self tapping screws supplied, attach the mounting brackets to the sides of the ACU. 3. Place the ACU in the location where it is going to be installed. 4.
Intellian Satellite TV Antenna Systems Advance Configuration – Up to 32 receivers for DIRECTV 99°W,101°W,and 103°W reception An Intellian 32 receiver expansion kit can be purchased with the antenna. In this configuration 2 SWM 16 switches are mounted below decks. Both switches require a 29v SWM power supply. RF L1 is connected through the ACU to a 2-way splitter, and then to the 13v0khz input on 2 SWM 16 switches. RF S1 connects through a 2-way splitter to the 18v0khz input on 2 SWM 16 switches.
Standard Configuration –Single receiver for Legacy DIRECTV reception RF L1 is connected to the ACU. RF L2 is connected directly to the receiver. For multiple receivers a separate multiswitch must be purchased. RF S1 must be connected to the 29v SWM power supply. Note: SWM Power Supply must be connected to S1 to power multiswitch inside antenna radome.
Intellian Satellite TV Antenna Systems Standard Configuration – Single or Multiple receivers for Legacy DIRECTV reception RF L1 needs to be connected through the ACU to the RHCP 13v0khz on the multiswitch. RF L2 needs to be connected to the LHCP 18v0khz on the multiswitch. RF S1 must be connected to the 29v SWM power supply. ACU S1 L2 Note: SWM Power Supply must be connected to S1 to power multiswitch inside antenna radome.
Standard configuration – Single receiver for Dish Network, Bell TV receptions RF L1 connects through the ACU to RF1 input on the MIM. RF L2 connects to the RF2 input on the MIM. RS-232 serial cable (supplied) is connected from the ACU to the MIM. RF S1 must be connected to the 29v SWM power supply. Note: SWM Power Supply must be connected to S1 to power multiswitch inside antenna radome.
Intellian Satellite TV Antenna Systems Standard Configuration – Multiple receivers for Dish Network, Bell TV receptions RF L1 connects through the ACU to RF1 input on the MIM. RF L2 connects to the RF2 input on the MIM. RS-232 serial cable (supplied) is connected from the ACU to the MIM. RF S1 must be connected to the 29v SWM power supply. Note: SWM Power Supply must be connected to S1 to power multiswitch inside antenna radome.
Connecting the System to a GPS Your satellite TV system has a built-in GPS. If the internal GPS doesn’t operate properly, you can directly connect your boat’s NMEA 0183GPS tothesystemthroughtheACU’s external GPS connector. To do this you will need lengths of cable suitable for connecting to your GPS system and the green 2-way ACU GPS connector supplied with your Intellian s6HDSatellite TV System. To Connect the System to a GPS 1.
Intellian Satellite TV Antenna Systems Multi-band Alignment Control Systems Intellian s6HD with an embedded multi-band alignment control systems keeps the multi-feed LNB aligned with the three DIRECTV satellites at sea even during harsh marine environment or high-speed cruising. PC to ACU Communication Setup You can establish data communication between a PC and the ACU using one of the following methods. Serial Connection Connection through Serial Port 1.
Wi-Fi Connection Setup Wi-Fi Connection • Setting up the PC in order to access Wi-Fi 1. Connect Wi-Fi. After clicking on the Windows Wireless Connection icon, click on i-AP(default). 2. By default, the connection security is opened. 3. Use the ACU’s IP address to access Intellian Aptus® • Default: 192.168.1.223 Figure 27 : ACU to PC Wifi Connection TCP/IP Connection Connection through Rear Panel Ethernet Port This method requires separate IP configuration on a PC. 1.
Intellian Satellite TV Antenna Systems Operation Instruction Introduction This section of the handbook describes how to setup your Satellite TV System after installing the ACU.
Operating the ACU ACU Soft Keys Normal Mode Start Up With the system installed and power applied, the ACU screen will show the following sequence: INITIALIZE ACU INTELLIAN s6HD POWER Press to select On-screen option BACK ENTER INITIALIZE ANTENNA 1. Data communication is being established between the antenna and the ACU. The ACU is initialized. 2. The antenna is initialized. INTELLIAN s6HD Figure 22 : ACU Soft Keys SEARCH A: DTV101 B:DTV99 SETUP TRACKING A: DTV101 B:DTV99 SETUP 3.
Intellian Satellite TV Antenna Systems Changing Target Satellite Your antenna is pre-programmed with either two (Dual-Sat mode) or three (Tri-Sat mode) candidates of target satellites as a default mode. To change a target satellite, press LEFT soft key. The target satellite is changed and is automatically tracked by the antenna. Tri-Sat Mode TRACKING A: DTV101 B: DTV99 DTV103# 1. Press LEFT soft key for tracking Satellite B.
Monitoring the Current Antenna Status When the powered on, ACU displays the status of the antenna. The current status of the antenna is displayed as shown below. SEARCH A: DTV101 B:DTV99 SETUP TRACKING A: DTV101 B:DTV99 SETUP ANTENNA IS UNWRAPING B:DTV99 SETUP TRACKING A: DTV101 B:DTV99 SETUP 1. The antenna is searching Satellite A. AZ : ###.# EL : ##.# SIGNAL : ### ● [VL] 2. The antenna is tracking Satellite A. ###.##E ##.##N 5. Antenna position detail and signal strength are displayed.
Intellian Satellite TV Antenna Systems Setup Mode Sleep Mode If the antenna has lost the tracked satellite while in sleep mode, sleep mode will be canceled. TRACKING B:DTV99 TRACKING B:DTV99 A: DTV101 1. Press BACK to enter sleep mode. SETUP A: DTV101 SETUP Begin Setup Mode To enter the Setup Mode simply follow the instructions below: TRACKING A: DTV101 B:DTV99 2. Press BACK again to exit sleep mode. 2. Press YES to enter setup mode. SETUP MODE ? NO YES 3.
Setting the Satellite Pair You can change the satellite pair if you decide to receive satellite television service from a different service provider. 1. Press YES to enter setup mode. SETUP MODE ? YES NO 2. Press YES to set satellite pair. SET SAT PAIR ? PREV YES NEXT SAT A : DTV101 PREV PREV NO SELECT NEXT SELECT 5. Set satellite B Press PREV to show previous satellite name. Press SELECT to set chosen satellite to SAT B. Press NEXT to show next satellite name. NEXT 6.
Intellian Satellite TV Antenna Systems Setting GPS It is possible to set up and modify the GPS information, which enhances the antenna functionality. 1. Press YES to enter setup mode. SETUP MODE ? YES - NO SET SAT PAIR ? PREV YES LONGITUDE ###.## E NEXT 2. Press NEXT to enter GPS setup mode. INPUT + LATITUDE ##.## N - INPUT + X1 3. Press YES to set GPS. SET GPS ? PREV YES NEXT SAVE ? YES LONGITUDE ###.## E - 32 INPUT + 4. Input the longitude data. + increases the value.
Edit Satellite Information It is possible to modify the existing satellite information and input new satellite information into the ACU as well. It is not recommended for a novice satellite service user to use this mode. 1. Press YES to enter setup mode. SETUP MODE ? YES NO SET SAT PAIR ? PREV YES NEXT 2. Press NEXT twice to enter edit satellite info mode. X2 YES SELECT + SAT NAME : DTV101 - INPUT + NEXT - 4. Set the satellite name. PREV - Shows previous satellite name.
Intellian Satellite TV Antenna Systems 9. Input the network ID (NID) for vertical low band. VER LOW NID 0x0003 - INPUT + HOR LOW 12523 21096 - INPUT + HOR LOW NID 0x0003 - INPUT + VER HIGH 12598 21096 - 34 INPUT + VER HIGH NID 0x0003 - 10. Input the tracking frequency (MHz) and symbol rate (KHz) for horizontal low band. 11. Input the network ID (NID) for horizontal low band. 12. Input the tracking frequency (MHz) and symbol rate (KHz) for vertical high band.
VOLTAGE : AUTO PREV SELECT NEXT DISEQC : AUTO PREV SELECT NEXT SAVE? YES NO 17. Select the Voltage Supply Method* to LNB. (AUTO is recommended) 18. Select the DISEQC Method*. (AUTO is recommended) 19. Press YES to save the input information. Press NO to cancel and return to main setup mode.
Intellian Satellite TV Antenna Systems Setting the Antenna Parameters It is not recommended for a novice satellite service user to use this mode. Consult Intellian for changing antenna parameters. 1. Press YES to enter setup mode. SETUP MODE ? SET SAT PAIR ? PREV YES WRS LEVEL : 0500 - NO YES NEXT INPUT 2. Press the NEXT three times to enter Set Antenna Parameter menu. X3 ANOTHER PARAMETER YES SET ANT PARAMETER PREV YES + NO NEXT SAVE ? PARAM: SCAN OFFSET 36 YES 6.
PARAM* Scan Offset The scan offset is to offset the angle difference between the black marker on the sub-reflector and the optical sensor. DiSEqC Level The DiSEqC level is to distinguish 0KHz tone and 22KHz tone. Track Scale The track scale is to control the tracking speed while antenna is tracking the satellite. Offset RH-LH The offset RH-LH is to offset the signal difference between RHCP and LHCP. Detect Level The detect level is to set the satellite signal detection level.
Intellian Satellite TV Antenna Systems Setting the LNB Local Frequency It is possible to select a local frequency from ACU. It is not recommended for a novice satellite service user to use this mode. Case1. Single band LNB is used. 1. Press YES to enter setup mode. SETUP MODE ? YES NO - SET SAT PAIR ? PREV YES LOCAL FREQ: #####MHz NEXT SAVE ? YES PREV YES 38 SELECT 3. Press YES to set local frequency. NEXT LNB TYPE : SINGLE PREV NEXT + 2.
Case 2. Universal LNB is used (Low band local frequency-9750 MHz/High band local frequency 10600 MHz). 1. Press YES to enter setup mode. SETUP MODE ? YES NO YES SET SAT PAIR ? PREV YES NEXT 2. P ress NEXT four times to enter set local frequency mode. X4 SET LOCAL FREQ ? PREV YES SELECT 3. Press YES to set local frequency. NEXT LNB TYPE : UNIVERSAL PREV SAVE ? NEXT NO 5. Press YES to accept the data. Press NO to cancel and return to main setup mode.
Intellian Satellite TV Antenna Systems Setting the DiSEqC Method DiSEqC selection can be made from ACU. It is not recommended for a novice satellite service user to use this mode. 1. Press YES to enter setup mode. SETUP MODE ? YES YES NO 2. Press NEXT five times to enter DISEQC mode. SET SAT PAIR ? PREV YES NEXT X5 3. Press YES to use DISEQC. USE DISEQC ? PREV YES NEXT DO NOT USE DISEQC PREV 40 SELECT SAVE ? NEXT 4. Select the DiSEqC Method* PREV - Shows previous DiSEqC Method.
Display Versions This sequence enables you to see what version of antenna and ACU software are installed on your system. 1. Press YES to enter Setup mode. SETUP MODE ? NO YES S/N: 0000000000 SET SAT PAIR ? PREV YES ANT S/W VER : 4.00 NEXT 2. Press NEXT six times to enter the View Version mode . EXIT ACU S/W VER : 0.01 S/N: 0000000000 EXIT 5. Antenna software version and S/N are shown. Press EXIT to return to main setup mode. 6. ACU software version and S/N are shown.
Intellian Satellite TV Antenna Systems Display Power 1. Press YES to enter setup mode. SETUP MODE ? EXIT SET SAT PAIR ? PREV YES NEXT 2. Press NEXT seven times to enter the view power mode. X7 3. Press YES to view power. VIEW POWER ? PREV YES NEXT ACU POWER : 27.1 V EXIT 42 ANT POWER : 25.9 V NO YES 4. ACU power is shown. Press any key to return to main setup mode. IRD : 18V + ##kHz EXIT 5. Antenna power is shown. Press any key to return to main setup mode. 6.
Setting Remote Control 1. Press YES to enter setup mode. SETUP MODE ? YES SET SAT PAIR ? PREV YES FUNC : SLEEP MODE NEXT NO NEXT 2. P ress NEXT eight times to enter remote control setting mode . SELECT EXIT PRESS A REMOTE KEY BACK EXIT X8 3. Press YES to set remote control. SET REMOCON ? PREV YES SELECT EXIT 4. Select the Function* NEXT - Shows next function. 6. Point remote control to ACU. Press any key on remote control for selected function and press same key again for confirmation.
Intellian Satellite TV Antenna Systems REMOTE KEY REGISTED FUNC : CHANGE SAT NEXT SELECT EXIT 9. R EMOTE KEY REGISTED will be displayed if key has been properly registered. 10. Press NEXT to show next function. Press EXIT to return to main setup mode. Function* CHANGE SAT - Change the target satellite. SLEEP MODE - Enter sleep mode. CLEAR REGISTERED KEY - Clear registered key.
Setting Antenna Go Position The antenna can be controlled manually by using the ACU. 1. Press YES to enter setup mode. SETUP MODE ? YES NO SET SAT PAIR ? PREV YES GO TO EL : ##.# - NEXT + INPUT 2. P ress NEXT nine times to enter Antenna Go Position mode. X9 GO TO POSITION ? YES YES 6. Press YES to move the antenna to input position. Press NO to return to the Antenna Go Position mode. 3. Press YES to go position. ANT GO POSITION ? PREV NO 5. Input position value for elevation (EL) axis.
Intellian Satellite TV Antenna Systems Setting Antenna Move Step The antenna can be moved by 1° step manually by using ACU. 1. Press YES to enter setup mode. SETUP MODE ? YES NO DOWN SET SAT PAIR ? PREV YES NEXT 2. P ress NEXT ten times to enter the Antenna Move Step mode. X10 3. Press YES to move step. ANT MOVE STEP ? PREV YES NEXT STEP AZ : ###.# CCW 46 EL STEP EL : ##.# CW 4. Move the antenna in the AZ axis. CW - Move the antenna clockwise. CCW - Move the antenna counter clockwise.
Executing Antenna Diagnosis The antenna status can be checked by reviewing the results of the diagnostic self-test of the antenna. Refer to the following codes to understand the test results. 1. Press YES to enter setup mode. SETUP MODE ? YES SET SAT PAIR ? PREV YES CODE 101 PASSED. RESULT: ● NO NEXT EXIT 5. CODE* 101 has passed. Press EXIT to return to main setup mode. 2. P ress NEXT eleven times to enter Antenna Diagnosis mode. X11 3. Press YES to diagnosis antenna.
Intellian Satellite TV Antenna Systems CODE* CODE 101 Data communication between antenna and antenna control unit is tested. If failed, check the RF cable. CODE 107 Skew System is tested. if failed, check the control board, skew motor, and skew sensor. CODE 102 AZ CW limit is tested. If failed, check the limit sensors, motor and belt for AZ axis. CODE 108 Antenna Input Power is tested. If failed, check the RF cable. CODE 103 AZ CCW limit is tested.
Setting Region 1. Press YES to enter setup mode. SETUP MODE ? YES NO PREV SET SAT PAIR ? PREV YES REGION : LOS_ANGELES NEXT 2. P ress NEXT twelve times to enter load region information mode. SELECT NEXT LOAD ? YES NO 5. Select the Region*. PREV - Shows previous region. SELECT - Set the displayed region. NEXT - Shows next region. 6. Press YES to load region information. Press NO to cancel and return to main setup mode.
Intellian Satellite TV Antenna Systems Setting the Factory Default Parameters This will restore the antenna back to factory default settings. 1. Press YES to enter setup mode. SETUP MODE ? YES NO SET SAT PAIR ? PREV YES NEXT 2. Press NEXT thirteen times to enter default setting mode. X13 3. Press YES to set default parameters.
ANTENNA CONTROL SOFTWARE Introduction to Aptus® Software, Aptus® Intellian’s new Antenna PC Controller is a nextgeneration graphically based antenna remote control software. The Aptus® allows users to easily and conveniently set up the antenna by using a personal computer. Software Installation Double click the ‘Aptus Setup.exe’ icon to install Aptus® directly onto your computer/ laptop. The InstallShield Wizard will guide you through the program setup process.
Intellian Satellite TV Antenna Systems PC to ACU Communication Setup Establish a data communication Starting Aptus® Access ACU through Serial Communication 1. Connect a 9 pin Serial cable between the PC INTERFACE connector on the ACU and the 9 pin Serial port on the PC. 2. Select Serial at communication type combo-box. 3. The baud rate of the ACU is 19200 for i-series. 4. Select a COM port which is not occupied by other devices. 5. Click the Connect button.
Auto Update Intellian Aptus® checks and notifies the latest version when it is started to maintain up to date software version by AutoUpdate function. 5. When file downloading is finished, “installing…” message is displayed and Aptus patch runs and the installation starts by InstallShield. 6. Click the “Finish” button when InstallShield installation is finished, then “Run the Aptus” message is displayed and Aptus runs and AutoUpdate is automatically finished. 1.
Intellian Satellite TV Antenna Systems Toolbar Menus The toolbar menus at the top of the screen display command buttons of the most commonly used functions of the Aptus®. The toolbar menus consists of 6 main menus; Quick (for quick launch of functions), File (not used on i-series), View(for user layout and work view), Connection(for communication), Utill(not used on i-series) and Help(for reporting problems and information check) . 1 1 2 3 Quick Setup: enters Setup mode.
2 File : Not used on i-Series. 3 View • User Layout: displays the layout list that the user has previously stored by using Layout Manager. If you select a layout in this list, the selected layout will be constructed in Work View screen. The ‘Basic layout’ is provided by default. • Layout Manager: provides the user with add, delete, and save functionalities in order to manage the user’s layouts. - Selecting ‘Add current layout’ opens a pop up window.
Intellian Satellite TV Antenna Systems 4 Connection At any time, data communication channel can be re-established between Serial and Network connection. Selecting Comm. Button will display Communication Window to connect to the ACU via Serial or Network communication. 5 Utill : Not used on i-Series. 6 Help • Report: provides e-mail contact to Intellian technical support team to let the user report problems at any time. ® • Information: displays the information of current Aptus software version.
System Property Status Dashboard The property status dashboard on the left pane of the screen provides the antenna status, the availability of TX transmission, signal level, GPS status, software information, product information and error status to be monitored quickly. Displays the status of the current mode of the antenna. - Search: Antenna is searching the selected satellite. - Tracking: Antenna is tracking the target satellite. - Initialize: Antenna or ACU is initializing.
Intellian Satellite TV Antenna Systems Displays the current GPS location from the Antenna information. The status light flashes green if the system receives a correct input of the GPS. 4 GPS: 5 Voltage: Displays the antenna and the ACU voltage information. 6 Software Information: Displays the antenna and the ACU firmware versions Displays the antenna and ACU serial numbers, antenna model and ACU model.
8 Diagnostic Error Report The square button next to the Diagnostic Error Report turns red when the system receives an error. Click the button to see a Diagnostic Report.
Intellian Satellite TV Antenna Systems Work View Tabs Aptus® provides seven Work View Tabs (Antenna Basic View, Antenna Advanced View, Satellite ViewMonitor View, Graph View, Diagnostic /Network View, and GUI View) to manage the Antenna and the Satellite configuration. How to modify the settings on Work View; 1. Enter the Setup mode by clicking Setup icon. 2. Tick the checkbox next to the “Set” button to modify the settings. 3. Enter the desired value then press the Set button to save the settings. 1.
- Antenna Angle: displays and sets current antenna’s absolute and relative AZ (azimuth) position, EL (elevation) position and polarization (between Linear and Circular). You can move antenna azimuth and elevation position and LNB Pol angle by using the arrows or inputting a value to find the desired satellite manually. 2. Antenna – Advanced Info. This view provides information on Parameter Setting, Threshold Setting, and Flag Setting. -Tilt Sensor Bias: not used on i-series.
Intellian Satellite TV Antenna Systems - Threshold Setting • Initial Sat Count: Set the threshold count for maintaining tracking. • Set Verify Time:Set the time of verifying whether the signal detected is the signal of target satellite. • Voltage Threshold: Set the voltage threshold. The voltage threshold is to distinguish the voltage between 13V and 18V. • DiSEqC Threshold: Set the DiSEqC threshold. The DiSEqC threshold is to distinguish the 0KHz tone and 22KHz tone.
- Dual Satellite Mode/ Triple Satellite Mode: Registers the target satellite. • Pushing ‘Register for Sat A’ or ‘Register for Sat B’ button after selecting the satellite in the list box makes it possible to register A or B in Dual Satellite Mode. • Pushing ‘Register for Sat A’ or ‘Register for Sat B’ or ‘Register for Sat C’ button after selecting the satellite in the list box makes it possible to register A or B or C in the Triple Satellite Mode.
Intellian Satellite TV Antenna Systems 4. Graph This view provides information on Signal, Elevation (EL), Absolute AZ (Azimuth), Relative AZ, Heading, AZ and EL in Single or Multi graph formats. - Start/Stop Save: the chosen item is saved within the data log. The data log which stores the information displayed in the graphs can be later used for a service technician to find out a cause of any possible problem to the antenna. - Clear All: clears everything drawn on the Graph View window. - Set Pos.
5. Monitor This view provides a UI which can monitor all data that has been received from the ACU. - Tracking: not used on i-series. - Rate Sensor Bias: not used on i-series. - Tilt Sensor Bias: not used on i-series. - Show Param: shows the current antenna parameters. - Check NID: verifies the NID (network ID) of the current tracking transponder. Press the NID button to obtain the NID only if the antenna is locked onto the desired satellite. - Start Debug: starts the debug log of the antenna.
Intellian Satellite TV Antenna Systems 6. Diagnostic / Network This view provides Antenna Diagnostic Testing and Network Settings. - Diagnostic : select to run a full diagnostic test or single diagnostic test. “Green” indicator is displayed for the test under progress. “Blue” indicates the test result as Pass while “Red” indicates the result as Fail. “Yellow” indicates the test has been skipped. • Serial Comm.: tests the data communication between the antenna and the ACU.
• Network Setting: • Wifi Setting: IP the network IP address. Power select to turn on or off Wifi network function. Subnet Mask the network subnet mask. SSID Gate Way the gateway for network. DNS the DNS address. the SSID is the network name shared among all devices in a wireless network. The SSID must be identical for all devices in the wireless network. It is case-sensitive and must not exceed 8 alphanumeric characters, which may be any keyboard character.
Intellian Satellite TV Antenna Systems 7. GUI This view shows a graphical representation of the current antenna position which allows you to easily identify whether or not the antenna is aligned properly to the target satellite or is in a block zone. In addition, this view shows the current satellite that the antenna is pointed towards and the satellites that are located at a 180°arc on the horizon, according to the current position. 8.
Move the selected Work View Tab to the bottom position of the Work View layout. Move the selected Work View Tab to the right position of the Work View layout. Move the selected Work View Tab to the left position of the Work View layout. Move the selected Work View Tab to the center position of the Work View layout. - Horizontal or Vertical Tab Group The Work View Tabs can be also aligned horizontally or vertically.
Intellian Satellite TV Antenna Systems - Zoom Tool Using the Zoom tool, you can easily select the magnification you want by using Zoom In and Zoom Out bar, and Fit in Work View button. Fit Work View Button: fits the current view to the Work View window size. The button toggles between the fit view and the previous view. Zoom In and Zoom Out Bar: zooms in and out to expand and reduce the View to the desired size. (The zoom changes in 10% increments.
Preparation for Transportation This is to describe how to prepare the antenna internally for transportation. The following procedures to secure the antenna shall be strictly observed to protect it from being damaged during transportation. 1. Refer to the drawing on the left. 2. Rotate antenna left and right slowly until the limit switch is pressed. 3. Turn the antenna by 360° to the reverse direction. 4.
Intellian Satellite TV Antenna Systems Warranty This product is warranted by Intellian Technologies Inc., to be free from defects in materials and workmanship for a period of THREE (3) YEARS on parts and ONE (1) YEAR on labor performed at Intellian Technologies, Inc. service center from the purchased date of the product. Intellian Technologies, Inc.
Appendix : s6HD Technical Specification General Antenna system performance Approvals CE – conforms to EU Directive 89/336/EEC FCC – verified to CFR47:Part 15 Dimensions Satellite antenna unit 70cm (27.5”) x 72cm(28.3”) Antenna dish diameter 60cm(23.6”) Antenna control unit 17.8cm(7”)x21.68cm(8.5”)x5.38cm(2.1”) Frequency 47 dBW Azimuth range 680° Elevation range +5° ~ +90° Weight 21.7kg (47.7 lbs) Antenna control unit 1.2kg (2.6 lbs) Ka-band (18.3 ~ 20.
Intellian Satellite TV Antenna Systems APAC supportAPAC@intelliantech.com Headquarters Intellian Technologies, Inc. 348-5 Chungho-Ri, Jinwi-Myeon Pyeongtaek-Si, Gyunggi-Do 451-862 Korea T +82 31 379 1000 F +82 31 377 6185 Seoul Office Intellian Technologies, Inc. 2F Dongik Building, 98 Nonhyun-Dong Gangnam-Gu, Seoul 135-010 Korea T +82 2 511 2244 F +82 2 511 2235 74 Americas EMEA supportAMERICAS@intelliantech.com supportEMEA@intelliantech.