TAG Heuer Connected Watch (Draft) INSTRUCTIONS AND INTERNATIONAL LIMITED GUARANTEE PART I. QUICK START GUIDE PART II. INTERNATIONAL WARRANTY PART I: QUICK START GUIDE - USER MANUAL Congratulations on your purchase. This document is a quick start guide providing information on your TAG Heuer connected device basic functions only. For more information and exclusive content, go to : http://customerservice.tagheuer.com. Each TAG Heuer Connected Watch is built to meet the most exacting requirements.
DISASSEMBLY PROCESS Process starting with a fully-assembled product leading to dis-assembly for part replacement purpose. A. First, you will separate the entity horn-strap (b)-(c) from the module (a). 1. Take your watch fully assembled and lay it down on the opposite side of the power button on a smooth surface so that you can see the caseback. On one side, place your thumb on the push button located under the horn while keeping your index and middle fingers on top of the horns.
2. . In an opposite movement, pull the horns horizontally in one direction while pulling the strap in the opposite direction. You should now have your horns and strap separated on one side. 3&4 Repeat step 1 & 2 on the other horn-strap entity to disassemble it. 5. You should now have your module (a) and horns (b) separated from your strap and buckle (c) & (d). C.
2&3. Once your strap metal part is in the link of your buckle, make sure all the parts of your strap, metal strap, link and buckle are aligned. 4&5. Take your loose strap part remaining to attach it to the buckle. You will insert the end piece into the dedicated end piece. Adjust the angle of insertion for smooth fitting. You can adjust the size of your strap by sliding this strap part here. As for the strap with metal part, make sure it is inserted in the right position to welcome horns later on. 6.
TURNING ON YOUR TAG HEUER CONNECTED WATCH 1. Connect your watch to a power source 2. Press and hold the power button for a few seconds 3. Tap the screen to begin 4. Tap a language TURNING OFF YOUR TAG HEUER CONNECTED WATCH 1. 2. 3. Press on power button Look for settings, tap system and select turn off. When prompted with message “Turn off: Are you sure?” Tap check mark. CHARGING YOUR TAG HEUER CONNECTED WATCH Before using your watch for the first time, you should charge the battery.
HOW TO USE YOUR NEW TAG HEUER CONNECTED WATCH For more information, please go to: http://customer-service.tagheuer.com “Swipe up “, swipe down will open quick settings. Add push crown to go back to watch face « Tap a notification to get more information » Google Assistant: Use your voice and say “Ok Google” and use a voice command or use a voice search: Try: “Ok Google show me my steps”. You can also long press the power button to launch the Google Assistant.
might result in the TAG Heuer Connected Watch becoming in- operative and dangerous. Charging accessories To charge the TAG Heuer Connected Watch, use only approved charging accessories. Your Watch is provided with the following charging accessories: micro USB cable, charging cradle, wall plug. Use only approved charging accessories. When a charger is not in use, disconnect it from the power source.
the back of the watch is clean. The charger contains a small magnet to ensure proper alignment and attachment of the watch to the charger. Please keep the charger away from metal. Battery safety Your TAG Heuer Connected Watch contains a built-in battery that is not replaceable. Do not attempt to replace your product’s battery (for information on the recycling of the battery, please refer to section C-2, below). In any event: .
The TAG Heuer Connected Watch can be damaged and battery life shortened if stored or operated outside of these temperature ranges. Avoid exposing the TAG Heuer Connected Watch to dramatic changes in temperature or humidity.
addition, the battery contained in your TAG Heuer Connected Watch is subject to Directive 2006/66/EC on batteries and accumulators and waste batteries and accumulators. The above-mentioned crossed- out wheeled bin symbols indicate that the TAG Heuer Connected Watch, its battery and its accessories are subject to these regulations. The above mentioned equipment and battery must be collected separately.
• when tested for use at the trunk was FCC SAR 0.032W/kg and EU SAR 0.0143 W/kg. • when tested for use at the wrist was FCC SAR 0.048W/kg, EU SAR was 0.0488W/kg • To disable the Watch’s radio (including Bluetooth and Wi-Fi) functions, please refer to section I.B.3, above. FCC Statement (USA) – Model SBF81 This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement. Important: required regulatory marks and certification information are provided on the device under the settings.
2. 3.
2 万一、この機器から移動体識別用の機内無線局に対して電波干渉の事例が発生した場合には、速 やかに使用周波数を変更するか又は電波の発射を停止した上、下記連絡先にご連絡頂き、混信回 避のための処置等(例えば、パーティションの設置など)についてご相談して下さい。