> Before Start > Part Names > Install > Initial Setup > Playback > Advanced Manual Troubleshooting | Supplementary Information, etc. AV Receiver DRX-R1.1 Basic Manual Before Start ............................................................................2 What's in the box......................................................................2 Part Names .............................................................................3 Part Names .......................................................
> Before Start > Part Names > Install > Initial Setup > Playback > Advanced Manual Troubleshooting | Supplementary Information, etc. What's in the box Before Start 1. Main unit (1) 2. Remote controller (RC-913R) (1), Batteries (AAA/R03) (2) 3. Speaker setup microphone (1) 0 Used during Initial Setup. 4. Indoor FM antenna (1) 5. AM loop antenna (1) 6. Power cord (1) ≥ Basic Manual (This manual) 1 2 3 4 5 6 2 0 Connect speakers with 4 Ω to 16 Ω impedance.
> Before Start > Part Names > Install > Initial Setup > Playback > Advanced Manual Troubleshooting | Supplementary Information, etc. (*)You can find details in the Advanced Manual. Part Names Par t Names Front Panel 1. Í On/Standby button 2. Hybrid Standby indicator: Lights if the unit enters standby mode when the features are enabled that continue to work when this unit is in standby, such as HDMI Standby Through and Network Standby. 3.
> Before Start > Part Names > Install > Initial Setup > Playback > Advanced Manual Troubleshooting | Supplementary Information, etc. (*)You can find details in the Advanced Manual. 12.Setup button: You can show advanced setting items on the TV and display to provide you with an even better experience. (*) 13.Cursor buttons ( / / / ) and Enter button: Select the item with the cursors and press Enter to confirm. Use them to tune to stations when using Tuner. 14.
> Before Start > Part Names > Install > Initial Setup > Playback > Advanced Manual Troubleshooting | Supplementary Information, etc. (*)You can find details in the Advanced Manual. Rear Panel 1. COMPONENT VIDEO IN/OUT jacks: Transfer the video signals of an AV component with a component video cable. (Compatible only with 480i or 576i resolution.) 2.
> Before Start > Part Names > Install > Initial Setup > Playback > Advanced Manual Troubleshooting | Supplementary Information, etc. (*)You can find details in the Advanced Manual. 13.12V 1A INPUT jack / ON/OFF switch: Used for connection with the HDBaseT Receiver. Refer to the Instruction Manual included with the HDBaseT Receiver for usage instructions. 14.AC INLET: The supplied power cord is connected. 15.RS232 port: For connection to the home control system. (*) 16.
> Before Start > Part Names > Install > Initial Setup > Playback > Advanced Manual Troubleshooting | Supplementary Information, etc. Installation procedure Install This unit can be used in a number of ways, depending on the layout of the speakers you are installing, and the connections made to external devices. Read the following to help make the installation process smoother.
> Before Start > Part Names > Install > Initial Setup > Playback > Advanced Manual Troubleshooting | Supplementary Information, etc. Step1: Speaker Layout 7.1 Channel System *1 *2 *3 ¢1: 22e to 30e, ¢2: 90e to 120e, ¢3: 135e to 150e 8 Front speakers output front stereo sound and a center speaker outputs center sound such as dialogs and vocals. Surround speakers create back sound field. Powered subwoofer reproduces bass sounds and creates rich sound field. This basic 5.
> Before Start > Part Names > Install > Initial Setup > Playback > Advanced Manual Troubleshooting | Supplementary Information, etc. Height Speakers-1 (Front High Speakers/Rear High Speakers) These are types of height speakers. Furthermore, by installing height speakers, you can select the Dolby Atmos listening mode, which realizes the most up-to-date 3D sound including overhead sounds, when the input format is Dolby Atmos. Front high speakers or rear high speakers should be situated at least 3´/0.
> Before Start > Part Names > Install > Initial Setup > Playback > Advanced Manual Troubleshooting | Supplementary Information, etc. Height Speakers-2 (Ceiling Speakers) *3 *2 *1 These are types of height speakers. Furthermore, by installing height speakers, you can select the Dolby Atmos listening mode, which realizes the most up-to-date 3D sound including overhead sounds, when the input format is Dolby Atmos.
> Before Start > Part Names > Install > Initial Setup > Playback > Advanced Manual Troubleshooting | Supplementary Information, etc. Height Speakers-3 (Dolby Enabled Speakers (Dolby Speakers)) *2 These are types of height speakers. Dolby enabled speakers are special speakers designed to face the ceiling so that sound is heard after bouncing off the ceiling so that sound appears to be coming from overhead.
> Before Start > Part Names > Install > Initial Setup > Playback > Advanced Manual Troubleshooting | Supplementary Information, etc. Bi-Amping the Speakers It is possible to connect front speakers supporting BiAmping to improve quality of the bass and treble. The effects and placements for speakers are the same as for a system that doesn't use Bi-Amping speakers. 0 "Speaker combinations" (P13) introduces some detailed examples of speaker combinations.
> Before Start > Part Names > Install > Initial Setup > Playback > Advanced Manual Troubleshooting | Supplementary Information, etc. Speaker combinations 0 In any of the combinations, up to two powered subwoofers can be connected. Speaker Channels FRONT CENTER SURROUND SURROUND BACK HEIGHT 1 HEIGHT 2 Bi-AMP (*1) ZONE 2 (*1) (ZONE SPEAKER) (P22) ZONE 3 (*1) (ZONE SPEAKER) (P23) 2.1 ch 3.1 ch 4.1 ch 5.1 ch 6.1 ch 7.1 ch 2.1.2 ch (*2) (*3) 3.1.2 ch (*2) (*3) 4.1.2 ch (*2) (*3) 5.1.
> Before Start > Part Names > Install > Initial Setup > Playback > Advanced Manual Troubleshooting | Supplementary Information, etc. Step2: Connect the Speakers Standard Connections (Pages 8 to 11) Refer to the illustration to connect the speaker system. (*) Depending on the combination of speakers, you may need to connect to other jacks. See "Points to note with speaker combinations" (P13) for details. Setup 0 Settings for the speaker configuration you have connected need to be made in "1.
> Before Start > Part Names > Install > Initial Setup > Playback > Advanced Manual Troubleshooting | Supplementary Information, etc. Connecting with Bi-Amping Speakers (Page 12) Connect front speakers compatible with Bi-Amping connection to the FRONT jacks and the HEIGHT 1 jacks. Make sure you remove the jumper bar fitted between the woofer jacks and tweeter jacks of the front speakers. See "Standard Connections (Pages 8 to 11)" (P14) for how to connect speakers other than the front speakers.
> Before Start > Part Names > Install > Initial Setup > Playback > Advanced Manual Troubleshooting | Supplementary Information, etc. Step3: Connect the TV & AV Components 1. Connect the TV To ARC TV For a TV that supports the ARC (Audio Return Channel) (*1) feature, use an HDMI cable and connect according to illustration "a". Choose an HDMI IN jack on the TV that supports ARC when connecting. *2 Setup 0 Settings are required to use the ARC function. Select "Yes" in "5.
> Before Start > Part Names > Install > Initial Setup > Playback > Advanced Manual Troubleshooting | Supplementary Information, etc. 2. Connect the HDMI AV Component This is an example of connection with an AV component that has an HDMI jack.
> Before Start > Part Names > Install > Initial Setup > Playback > Advanced Manual Troubleshooting | Supplementary Information, etc. 3. Connect the Non-HDMI AV Component This is an example of connection with an AV component that does not have an HDMI jack. Make the connections to the AV component to match the jacks it has.
> Before Start > Part Names > Install > Initial Setup > Playback > Advanced Manual Troubleshooting | Supplementary Information, etc. 4. Connect the Audio Component Example of a connection with an audio component. Connect a CD player using a digital optical cable or analog audio cable. You can also connect a turntable that has an MM-type cartridge to the PHONO jack. 0 If the turntable has a built-in audio equalizer, connect it to an AUDIO IN jack other than the PHONO jack.
> Before Start > Part Names > Install > Initial Setup > Playback > Advanced Manual Troubleshooting | Supplementary Information, etc. 5. Connect the Component Video Monitor Use a component video cable to connect a TV or projector that has component video input jacks rather than an HDMI input jack. To output video from the COMPONENT VIDEO OUT jacks, you must connect the external AV components using a component video cable. a BD/DVD Projector, etc.
> Before Start > Part Names > Install > Initial Setup > Playback > Advanced Manual Troubleshooting | Supplementary Information, etc. 6. Multi-zone Connection-1 (ZONE 2 TV) You can enjoy content from a Blu-ray Disc player on a TV equipped with an HDMI input jack in the separate room (ZONE 2) by playing a Blu-ray Disc player in the main room (where this unit is located), or play the content from another AV component.
> Before Start > Part Names > Install > Initial Setup > Playback > Advanced Manual Troubleshooting | Supplementary Information, etc. 7. Multi-zone Connection-2 (ZONE 2 PRE/ LINE OUT / ZONE 2 SPEAKER) You can enjoy audio in the separate room by, for example, playing a Blu-ray Disc player in the main room (where this unit is located) and listening to internet radio in the separate room (ZONE 2).
> Before Start > Part Names > Install > Initial Setup > Playback > Advanced Manual Troubleshooting | Supplementary Information, etc. 8. Multi-zone Connection-3 (ZONE 3 PRE/ LINE OUT / ZONE 3 SPEAKER) Along with the main room and ZONE 2, you can also enjoy audio in yet another room (ZONE 3). Connections with an AV component To output the audio of an external AV component to ZONE 3, connect using an analog audio cable.
> Before Start > Part Names > Install > Initial Setup > Playback > Advanced Manual Troubleshooting | Supplementary Information, etc. 9. Connect Other Cables (North American models) Antenna Hookup (Australian models) Move the antenna around while playing the radio to find the position with the best reception. Use a thumb tack or similar to attach the indoor FM antenna to a wall. aa Network Hookup a Connect this unit to the network using wired LAN.
> Before Start > Part Names > Install > Initial Setup > Playback > Advanced Manual Troubleshooting | Supplementary Information, etc. Initial Setup with Auto Start-up Wizard Initial Setup Initial Setup Starts Automatically 1 INPUT TV When you turn the unit on for the first time after purchasing it, Initial Setup is automatically shown on the TV to enable you to make settings required for startup using simple operations following onscreen guidance. 1.
> Before Start > Part Names > Install > Initial Setup > Playback > Advanced Manual Troubleshooting | Supplementary Information, etc. environment of the room. 0 Calibration takes between 3 and 12 minutes to be completed. The speakers emit the test tone at high volume during measurement, so be careful of your surroundings. Keep the room as quiet as possible during measurement. 0 If you have connected a subwoofer, check the power and volume of the subwoofer. Set the subwoofer volume to more than halfway.
> Before Start > Part Names > Install > Initial Setup > Playback > Advanced Manual Troubleshooting | Supplementary Information, etc. AV Component Playback Playback 1 2 3 INPUT TV Basic Operations You can play the audio from AV components such as Blu-ray Disc players through this unit. 0 When a TV is connected to the HDMI OUT SUB jack, press Q (P6) on the remote controller and use "Other" "HDMI Out" to switch between MAIN and SUB.
> Before Start > Part Names > Install > Initial Setup > Playback > Advanced Manual Troubleshooting | Supplementary Information, etc. Network Functions 1 2 3 INPUT TV Basic Operations By connecting this unit to the network you can enjoy internet radio services such as TuneIn, streaming from Spotify Connect, and wireless playback using AirPlay® features. Furthermore, you can use the Music Server feature to stream music files stored on PCs or NAS devices that support the home network feature.
> Before Start > Part Names > Install > Initial Setup > Playback > Advanced Manual Troubleshooting | Supplementary Information, etc. USB Storage Device 1 2 3 4 INPUT TV Basic Operations You can play music files stored on a USB storage device. Perform the following procedure when the unit is on. 1. Switch the input on the TV to that assigned to the unit. 2. Plug your USB storage device with the music files into the USB port of this unit’s rear panel. 3.
> Before Start > Part Names > Install > Initial Setup > Playback > Advanced Manual Troubleshooting | Supplementary Information, etc. Listening to the AM/FM Radio 1 You can receive AM and FM radio stations on this unit with the built-in tuner. Perform the following procedure when the unit is on. ∫ Tuning into a Radio Station Tuning Automatically 1. Press Tuner (a) on the remote controller repeatedly to select either "AM" or "FM" on the display. 2.
> Before Start > Part Names > Install > Initial Setup > Playback > Advanced Manual Troubleshooting | Supplementary Information, etc. 1 2 3 ∫ Using RDS (Australian models) RDS stands for Radio Data System and is a method of transmitting data in FM radio signals. In regions using RDS, the radio station name is displayed when you tune into a radio station broadcasting program information. When you press on the remote controller in this state, you can use the following functions.
> Before Start > Part Names > Install > Initial Setup > Playback > Advanced Manual Troubleshooting | Supplementary Information, etc. Multi-zone 1 Basic Operations You can enjoy audio in the separate room by, for example, playing a Blu-ray Disc player in the main room (where this unit is located) and listening to internet radio in the separate room (ZONE 2/ZONE 3). 0 DSD and Dolby TrueHD audio signals are not output to ZONE 2/ZONE 3 when selected with the "NET" input selector.
> Before Start > Part Names > Install > Initial Setup > Playback > Advanced Manual Troubleshooting | Supplementary Information, etc. To turn off the function: Press Í while in the mode for controlling ZONE 2 or ZONE 3 on the remote controller. Playing in ZONE 2 or ZONE 3 only: If you turn the unit to standby during multizone playback, the Z2 or Z3 indicator is dimmed and the playback mode is switched to playback in a separate room only.
> Before Start > Part Names > Install > Initial Setup > Playback > Advanced Manual Troubleshooting | Supplementary Information, etc. Listening Mode This unit is equipped with a variety of listening modes, and you can select the optimum listening mode for movies, TV, music, and games using Movie/TV, Music, and Game (b). The basic operations are introduced in the Basic Manual. For more details, see the Advanced Manual.
® Manufactured under license from Dolby Laboratories. Dolby, Dolby Atmos, Dolby Surround, Dolby Vision and the double-D symbol are trademarks of Dolby Laboratories. For DTS patents, see http://patents.dts.com. Manufactured under license from DTS, Inc. DTS, the Symbol, DTS in combination with the Symbol, DTS:X, and the DTS:X logo are registered trademarks or trademarks of DTS, Inc. in the United States and/or other countries. © DTS, Inc. All Rights Reserved. THX and the THX logo are trademarks of THX Ltd.
1-10-5 Yokoami,Sumida-ku,Tokyo 130-0015 Japan http://www.integraworldwide.com 18 Park Way, Upper Saddle River, N.J. 07458, U.S.A. Tel: 800-225-1946, 201-818-9200 Fax: 201-785-2650 http://www.integrahometheater.com Gutenbergstrasse 3, 82178 Puchheim, Germany Tel: +49-8142-4401-0 Fax: +49-8142-4208-213 http://www.integra.eu 302, Building 1, 20 North Chaling Rd., Xuhui District, Shanghai, China 200032, Tel: +86-21-52131366 Fax: +86-21-52130396 http://www.integra.com.
>> Specifications >> Advanced Setup >> Listening Modes >> Network Functions >>Basic Manual Troubleshooting | Supplementary Information, etc. AV Receiver DRX-R1.1 Advanced Manual Specifications General Specifications............................................................. 2 About HDMI ............................................................................. 4 Playback from USB storage devices ....................................... 5 Playback from the Music Server ............................
>> Specifications >> Advanced Setup >> Listening Modes >> Network Functions >>Basic Manual Troubleshooting | Supplementary Information, etc. General Specifications ■ Amplifier Section 2 Rated Output Power (FTC) (North American) With 8 ohm loads, both channels driven, at 1 kHz; rated 140 watts per channel minimum RMS power, with no more than 0.08% total harmonic distortion from 250 milliwatts to rated output.
>> Specifications >> Advanced Setup >> Listening Modes >> Network Functions >>Basic Manual Troubleshooting | Supplementary Information, etc. Use one of the following Ethernet cables to connect.
>> Specifications >> Advanced Setup >> Listening Modes >> Network Functions >>Basic Manual Troubleshooting | Supplementary Information, etc. About HDMI ■ Compatible functions HDMI (High Definition Multimedia Interface) is a digital interface standard for connecting TVs, projectors, Bluray Disc/DVD players, set-top boxes, and other video components. Until now, several separate video and audio cables have been required to connect AV components.
>> Specifications >> Advanced Setup >> Listening Modes >> Network Functions >>Basic Manual Troubleshooting | Supplementary Information, etc. Playback from USB storage devices ■ Displaying the artist name, album name, and artwork for WAV format When playing WAV format music files, you can display information such as the artist name, album name, and art work on the display of the main unit, on the TV screen, and in the screen of the Integra Control Pro app.
>> Specifications >> Advanced Setup >> Listening Modes >> Network Functions >>Basic Manual Troubleshooting | Supplementary Information, etc. Playback from the Music Server ■ Supported Audio Formats This unit supports the following music file formats. Remote play of FLAC and DSD is not supported. MP3 (.mp3/.MP3): • Supported formats: MPEG-1/MPEG-2 Audio Layer 3 • Supported sampling rates: 44.1 kHz, 48 kHz • Supported bitrates: Between 8 kbps and 320 kbps. WMA (.wma/.WMA): • Supported sampling rates: 44.
>> Specifications >> Advanced Setup >> Listening Modes >> Network Functions >>Basic Manual Troubleshooting | Supplementary Information, etc. 1. Input/Output Assign Setup Menu The unit allows you to configure advanced settings to provide you with an even better experience. Operation: Use the on-screen displays (OSD) that appear on the TV to make the settings. on the remote controller to display the Setup menu.
>> Specifications >> Advanced Setup >> Listening Modes >> Network Functions >>Basic Manual Troubleshooting | Supplementary Information, etc. 8 Setting Item Default Value Setting Details Setting Item Default Value Setting Details Zone 2 HDMI Not Use Make the setting when you output to the Zone 2 TV connected to the HDMI OUT ZONE 2/SUB jack.
>> Specifications >> Advanced Setup >> Listening Modes >> Network Functions >>Basic Manual Troubleshooting | Supplementary Information, etc. ■ 2. HDMI Input Setting Item Default Value Setting Details You can change input assignment between the input selectors and HDMI IN jacks. PHONO --- "HDMI 1 (HDCP 2.2)" to "HDMI 7": Assign a desired HDMI IN jack to the Phono button. If you do not assign a jack, select "---".
>> Specifications >> Advanced Setup >> Listening Modes >> Network Functions >>Basic Manual Troubleshooting | Supplementary Information, etc. Setting Item Default Value Setting Details Setting Item Default Value Setting Details CD --- "COMPONENT 1", "COMPONENT 2": Assign the COMPONENT VIDEO IN jacks to the CD button. "VIDEO 1", "VIDEO 2": Assign a desired VIDEO IN jack to the CD button.
>> Specifications >> Advanced Setup >> Listening Modes >> Network Functions >>Basic Manual Troubleshooting | Supplementary Information, etc. ■ 5. Analog Audio Input 2. Speaker You can change input assignment between the input selectors and AUDIO IN jacks. If you do not assign a jack, select "---". Setting Item Default Value Setting Details BD/DVD AUDIO 3 "AUDIO 1" to "AUDIO 6": Assign a desired AUDIO IN jack to the BD/DVD button.
>> Specifications >> Advanced Setup >> Listening Modes >> Network Functions >>Basic Manual Troubleshooting | Supplementary Information, etc. 12 Setting Item Default Value Setting Details Setting Item Default Value Setting Details Height 1 Speaker Top Front Set the speaker type if height speakers are connected to the HEIGHT 1 terminals.
>> Specifications >> Advanced Setup >> Listening Modes >> Network Functions >>Basic Manual Troubleshooting | Supplementary Information, etc. Setting Item Default Value Setting Details Bi-Amp No Set whether the front speakers are bi-amp connected.
>> Specifications >> Advanced Setup >> Listening Modes >> Network Functions >>Basic Manual Troubleshooting | Supplementary Information, etc. Setting Item Default Value Setting Details Setting Item Default Value Setting Details Height 2 80Hz (THX) Select the crossover frequency from "40Hz" to "200Hz" to start outputting frequencies for each channel. "Full Band": Full band will be output. • "Full Band" can be selected only when "Front" is set to "Full Band".
>> Specifications >> Advanced Setup >> Listening Modes >> Network Functions >>Basic Manual Troubleshooting | Supplementary Information, etc. Setting Item Default Value Setting Details Surr Back Left 7' 0" / 2.10 m Specify the distance between each speaker and the listening position. Surround Left 7' 0" / 2.10 m Specify the distance between each speaker and the listening position. Subwoofer 1 12' 0" / 3.60 m Specify the distance between each speaker and the listening position.
>> Specifications >> Advanced Setup >> Listening Modes >> Network Functions >>Basic Manual Troubleshooting | Supplementary Information, etc. Setting Item Default Value Setting Details ■ 6. Equalizer Settings Surr Back Right 0.0 dB Select a value between "−12.0 dB" and "+12.0 dB" (in 0.5 dB increments). A test tone will be output each time you change the value. Select the desired level. You can adjust the output volume of the range of each connected speaker.
>> Specifications >> Advanced Setup >> Listening Modes >> Network Functions >>Basic Manual Troubleshooting | Supplementary Information, etc. ■ 7. THX Audio Setting item Default Value Setting Details Back Speaker Spacing >4.0 ft/>1.2 m Select the distance between the surround back speakers from "<1.0 ft/<0.3 m", "1.0 - 4.0 ft/0.3 - 1.2 m", and ">4.0 ft/>1.2 m". • The unit of distance (feet / meters) shown is the unit selected for use in "Distance".
>> Specifications >> Advanced Setup >> Listening Modes >> Network Functions >>Basic Manual Troubleshooting | Supplementary Information, etc. ■ 2. Dolby 3. Audio Adjust Make advanced settings such as those related to multiplex audio, settings for the LFE level, or those related to the volume of this unit. ■ 1.
>> Specifications >> Advanced Setup >> Listening Modes >> Network Functions >>Basic Manual Troubleshooting | Supplementary Information, etc. ■ 5. Volume 4. Source Setting Item Default Value Setting Details Volume Display Absolute Switch the volume display between the absolute value and relative value. The absolute value 82.0 is equivalent to the relative value 0.0dB. "Absolute": Absolute value such as "0.5" and "99.5" "Relative": Relative value such as "-81.5dB" and "+18.
>> Specifications >> Advanced Setup >> Listening Modes >> Network Functions >>Basic Manual Troubleshooting | Supplementary Information, etc. • To name a preset radio station, press Tuner on the remote controller, select AM/FM and select the preset number. • This cannot be set if the "NET" input is selected.
>> Specifications >> Advanced Setup >> Listening Modes >> Network Functions >>Basic Manual Troubleshooting | Supplementary Information, etc. 5. Listening Mode Preset 6. Hardware You can preset your favorite listening mode to each input. (For example, you can always apply straight decode to the Dolby TrueHD source of Blu-ray Disc to play it in unchanged sound field.) When the list of input sources is displayed, set the signal type and listening mode.
>> Specifications >> Advanced Setup >> Listening Modes >> Network Functions >>Basic Manual Troubleshooting | Supplementary Information, etc. 22 Setting Item Default Value Setting Details Setting Item Default Value Setting Details HDMI Standby Through Off When this is set to anything other than "Off", you can play the video and audio of an HDMI connected player on the TV even if the unit is in standby mode. Only "Auto" and "Auto(Eco)" can be selected if "HDMI CEC" is set to "On".
>> Specifications >> Advanced Setup >> Listening Modes >> Network Functions >>Basic Manual Troubleshooting | Supplementary Information, etc. ■ 2. Network • When LAN is configured with a DHCP, set "DHCP" to "Enable" to configure the setting automatically. ("Enable" is set by default) To assign fixed IP addresses to each components, you must set "DHCP" to "Disable" and assign an address to this unit in "IP Address" as well as set information related to your LAN, such as Subnet Mask and Gateway.
>> Specifications >> Advanced Setup >> Listening Modes >> Network Functions >>Basic Manual Troubleshooting | Supplementary Information, etc. Setting Item Default Value AirPlay Password 24 Setting Details You can set a password of up to 31 characters so that only registered users can use AirPlay®. 1. Press Enter to display the Edit screen. 2. Select a character or symbol with the cursors and press Enter. Repeat it to input 31 or less characters. "A/a": Switches between upper and lower cases.
>> Specifications >> Advanced Setup >> Listening Modes >> Network Functions >>Basic Manual Troubleshooting | Supplementary Information, etc. ■ 3. Power Management Setting Item Default Value Setting Details Sleep Timer Off Allows the unit to enter standby automatically when the specified time elapses. Select a value from "30 minutes", "60 minutes", and "90 minutes". "Off": Does not turn the unit to standby automatically.
>> Specifications >> Advanced Setup >> Listening Modes >> Network Functions >>Basic Manual Troubleshooting | Supplementary Information, etc. 26 Setting Item Default Value Setting Details Setting Item Default Value Setting Details BD/DVD Main Set the 12V trigger output setting to each input. "Off": No output "Main": Output when "BD/DVD" is selected as input for main room. "Zone 2": Output when "BD/DVD" is selected as input for ZONE2.
>> Specifications >> Advanced Setup >> Listening Modes >> Network Functions >>Basic Manual Troubleshooting | Supplementary Information, etc. Setting Item Default Value Setting Details Setting Item Default Value Setting Details PC Main Set the 12V trigger output setting to each input. "Off": No output "Main": Output when "PC" is selected as input for main room. "Zone 2": Output when "PC" is selected as input for ZONE2. "Main/Zone 2": Output when "PC" is selected as input for main room or ZONE2.
>> Specifications >> Advanced Setup >> Listening Modes >> Network Functions >>Basic Manual Troubleshooting | Supplementary Information, etc. 28 Setting Item Default Value Setting Details Setting Item Default Value Setting Details PHONO Main Set the 12V trigger output setting to each input. "Off": No output "Main": Output when "PHONO" is selected as input for main room. "Zone 2": Output when "PHONO" is selected as input for ZONE2.
>> Specifications >> Advanced Setup >> Listening Modes >> Network Functions >>Basic Manual Troubleshooting | Supplementary Information, etc. Setting Item Default Value Setting Details Setting Item Default Value Setting Details BD/DVD Zone 2 Set the 12V trigger output setting to each input. "Off": No output "Main": Output when "BD/DVD" is selected as input for main room. "Zone 2": Output when "BD/DVD" is selected as input for ZONE2.
>> Specifications >> Advanced Setup >> Listening Modes >> Network Functions >>Basic Manual Troubleshooting | Supplementary Information, etc. 30 Setting Item Default Value Setting Details Setting Item Default Value Setting Details PC Zone 2 Set the 12V trigger output setting to each input. "Off": No output "Main": Output when "PC" is selected as input for main room. "Zone 2": Output when "PC" is selected as input for ZONE2.
>> Specifications >> Advanced Setup >> Listening Modes >> Network Functions >>Basic Manual Troubleshooting | Supplementary Information, etc. Setting Item Default Value Setting Details Setting Item Default Value Setting Details PHONO Zone 2 Set the 12V trigger output setting to each input. "Off": No output "Main": Output when "PHONO" is selected as input for main room. "Zone 2": Output when "PHONO" is selected as input for ZONE2.
>> Specifications >> Advanced Setup >> Listening Modes >> Network Functions >>Basic Manual Troubleshooting | Supplementary Information, etc. 32 Setting Item Default Value Setting Details Setting Item Default Value Setting Details BD/DVD Main/Zone 2/ Zone 3 Set the 12V trigger output setting to each input. "Off": No output "Main": Output when "BD/DVD" is selected as input for main room. "Zone 2": Output when "BD/DVD" is selected as input for ZONE2.
>> Specifications >> Advanced Setup >> Listening Modes >> Network Functions >>Basic Manual Troubleshooting | Supplementary Information, etc. Setting Item Default Value Setting Details Setting Item Default Value Setting Details PC Main/Zone 2/ Zone 3 Set the 12V trigger output setting to each input. "Off": No output "Main": Output when "PC" is selected as input for main room. "Zone 2": Output when "PC" is selected as input for ZONE2.
>> Specifications >> Advanced Setup >> Listening Modes >> Network Functions >>Basic Manual Troubleshooting | Supplementary Information, etc. 34 Setting Item Default Value Setting Details Setting Item Default Value Setting Details PHONO Main/Zone 2/ Zone 3 Set the 12V trigger output setting to each input. "Off": No output "Main": Output when "PHONO" is selected as input for main room. "Zone 2": Output when "PHONO" is selected as input for ZONE2.
>> Specifications >> Advanced Setup >> Listening Modes >> Network Functions >>Basic Manual Troubleshooting | Supplementary Information, etc. 7. Multi Zone Setting Item Make settings related to Multi-zone Connection, such as the volume for the separate room. Default Value Power On Volume Last ■ 1. Zone 2 Setting Item Default Value Setting Details Output Level Fixed Select whether to adjust the volume on the premain amplifier in the separate room or on this unit when outputting to Zone 2.
>> Specifications >> Advanced Setup >> Listening Modes >> Network Functions >>Basic Manual Troubleshooting | Supplementary Information, etc. ■ 2. Remote ID 8. Miscellaneous Change the frequency step for the tuner, update the firmware, and perform Initial Setup, etc. ■ 1. Tuner 36 Setting Item Default Value AM / FM Frequency Step (North American models) 10 kHz / 0.2 MHz Select a frequency step depending on your area of residence. Select "10 kHz/0.2 MHz" or "9 kHz/0.05 MHz".
>> Specifications >> Advanced Setup >> Listening Modes >> Network Functions >>Basic Manual Troubleshooting | Supplementary Information, etc. ■ 3. Preamp Mode ■ 4. Firmware Update If speakers are connected to the PRE OUT jacks on this unit via a power amplifier, you can reduce the power consumed by this unit by turning off the power supplied to the SPEAKERS terminals you are not using on this unit.
>> Specifications >> Advanced Setup >> Listening Modes >> Network Functions >>Basic Manual Troubleshooting | Supplementary Information, etc. listening to some sound. Subwoofer 1 / Subwoofer 2 : Adjust the speaker level of the subwoofer while listening to some sound. Quick Menu You can quickly adjust settings you frequently use, such as tone adjustments, etc. Operation: You can make the settings on the TV screen while playing something. Press Q on the remote controller to display the Quick Menu.
>> Specifications >> Advanced Setup >> Listening Modes >> Network Functions >>Basic Manual Troubleshooting | Supplementary Information, etc. • The effect may not be selectable with some content. Screen Centered Dialog: Front high speakers are used to move acoustic images such as dialogs from the center speakers upward according to the height of the TV screen. Acoustic images of the center speakers move up as the set value is increased. • Depending on the speaker settings, this becomes "Off".
>> Specifications >> Advanced Setup >> Listening Modes >> Network Functions >>Basic Manual Troubleshooting | Supplementary Information, etc. the MAC address and IP address for this unit. Web Setup You can make the settings for network features for this unit in an internet browser on a PC, smartphone, etc. on the remote controller to display the Setup 1. Press menu. 2. Select "6. Hardware" - "Network" with the cursors, then take a note of the IP address displayed in "IP Address". 3.
>> Specifications >> Advanced Setup >> Listening Modes >> Network Functions >>Basic Manual Troubleshooting | Supplementary Information, etc. Control Function Settings You can enable the control functions between the unit and external devices. Special devices or cable connections are necessary to enable the functions. For more information about installation, contact a store specializing in these products.
>> Specifications >> Advanced Setup >> Listening Modes >> Network Functions >>Basic Manual Troubleshooting | Supplementary Information, etc. Miscellaneous" - "Preamp Mode" in the Setup menu. Connecting a Power Amplifier You can connect a power amplifier to the unit and use the unit as a pre-amplifier in order to produce a large volume that cannot be output with the unit only. Connect the speakers to the power amplifier. For details, refer to the power amplifier's instruction manual. ■ Connections 1.
>> Specifications >> Advanced Setup >> Listening Modes >> Network Functions >>Basic Manual Troubleshooting | Supplementary Information, etc. Firmware Update The updating function on this unit This unit has functionality to update the firmware (the system software) over a network or by the USB port. This enables us to make improvements to a variety of operations and to add features. • For the latest information on updates, visit our company's website.
>> Specifications >> Advanced Setup >> Listening Modes >> Network Functions >>Basic Manual Troubleshooting | Supplementary Information, etc. Setup 1. Input/Output Assign 1. Tuner 2. Speaker 2. Remote ID 3. Audio Adjust 3. Preamp Mode 4. Source 4. Firmware Update 5. Listening Mode Preset 5. Initial Setup 6. Hardware 6. Lock 7. Multi Zone 8. Miscellaneous • If "Firmware Update" is grayed out and cannot be selected, wait for a while until it starts up.
>> Specifications >> Advanced Setup >> Listening Modes >> Network Functions >>Basic Manual Troubleshooting | Supplementary Information, etc. 4. Connect the USB storage device to the USB port of the unit. • If you connect a USB hard disk drive to the USB port of the unit, we recommend that you use its AC adapter to power it. • If the USB storage device has been partitioned, each section will be treated as an independent device. 5. Press on the remote controller.
>> Specifications >> Advanced Setup >> Listening Modes >> Network Functions >>Basic Manual Troubleshooting | Supplementary Information, etc. Selecting Listening Modes Select the optimum listening mode for movies, TV, music, and games by repeatedly pressing the Movie/TV, Music, and Game buttons. 1. During play, press one of the following three buttons on the remote controller. 2. Press the selected button repeatedly to switch the modes displayed on the display of the unit.
>> Specifications >> Advanced Setup >> Listening Modes >> Network Functions >>Basic Manual Troubleshooting | Supplementary Information, etc. Listening Mode Effects In alphabetical order ■ AllCh Stereo This mode is ideal for background music. Stereo sound is played through the surround speakers as well as the front speakers, creating a stereo image. ■ Direct This listening mode can be selected for all input signals.
>> Specifications >> Advanced Setup >> Listening Modes >> Network Functions >>Basic Manual Troubleshooting | Supplementary Information, etc. bass region (sound elements for the subwoofer). Detailed reproduction is achieved by recording the content at a sampling rate of 96 kHz at a resolution of 24 bits. • To enable transfer of this audio format, connect via digital cable and set audio output on the player to bitstream output.
>> Specifications >> Advanced Setup >> Listening Modes >> Network Functions >>Basic Manual Troubleshooting | Supplementary Information, etc. ■ T-D (Theater-Dimensional) In this mode, you can enjoy a virtual playback of multichannel surround sound even with only two or three speakers. This works by controlling how sounds reach the listener's left and right ears. ■ THX THX is a series of specifications for the accurate reproduction of movies propounded by the film director George Lucas.
>> Specifications >> Advanced Setup >> Listening Modes >> Network Functions >>Basic Manual Troubleshooting | Supplementary Information, etc. Selectable Listening Modes You can select a variety of listening modes to suit the audio format of the signal being input. Refer to the following for the listening mode choices. • Listening modes available when headphones are connected are: Mono, Direct, and Stereo. Only Mono or Stereo can be selected when the input signal is DSD.
>> Specifications >> Advanced Setup >> Listening Modes >> Network Functions >>Basic Manual Troubleshooting | Supplementary Information, etc. Input Format Listening Mode Input Format Listening Mode Input Format Listening Mode Dolby Atmos • You can select the Dolby Digital Plus or Dolby TrueHD listening modes if surround back speakers or height speakers are not connected.
>> Specifications >> Advanced Setup >> Listening Modes >> Network Functions >>Basic Manual Troubleshooting | Supplementary Information, etc.
>> Specifications >> Advanced Setup >> Listening Modes >> Network Functions >>Basic Manual Troubleshooting | Supplementary Information, etc. ■ Music button Input Format Listening Mode Input Format Listening Mode This is a list of listening modes you can select according to the audio format of the input signal.
>> Specifications >> Advanced Setup >> Listening Modes >> Network Functions >>Basic Manual Troubleshooting | Supplementary Information, etc.
>> Specifications >> Advanced Setup >> Listening Modes >> Network Functions >>Basic Manual Troubleshooting | Supplementary Information, etc.
>> Specifications >> Advanced Setup >> Listening Modes >> Network Functions >>Basic Manual Troubleshooting | Supplementary Information, etc.
>> Specifications >> Advanced Setup >> Listening Modes >> Network Functions >>Basic Manual Troubleshooting | Supplementary Information, etc. ■ Game button This is a list of listening modes you can select according to the audio format of the input signal.
>> Specifications >> Advanced Setup >> Listening Modes >> Network Functions >>Basic Manual Troubleshooting | Supplementary Information, etc.
>> Specifications >> Advanced Setup >> Listening Modes >> Network Functions >>Basic Manual Troubleshooting | Supplementary Information, etc. Input Format Listening Mode Input Format Listening Mode Input Format Listening Mode Dolby TrueHD Direct DTS Direct DTS 96/24 Direct Dolby TrueHD DTS 1 2 DTS Neural:X THX Games THX Games THX S Games Game-RPG Game-RPG Game-RPG Game-Rock Full Mono 6 T-D 6 Cannot be selected when the input format is 2 ch.
>> Specifications >> Advanced Setup >> Listening Modes >> Network Functions >>Basic Manual Troubleshooting | Supplementary Information, etc.
>> Specifications >> Advanced Setup >> Listening Modes >> Network Functions >>Basic Manual Troubleshooting | Supplementary Information, etc. Input Format Listening Mode DTS-ES Direct DTS 1 ES Matrix 2 ES Discrete 2 DTS Neural:X THX Games 3 Game-RPG 4 Game-Action Game-Rock 4 4 Game-Sports AllCh Stereo Full Mono 4 5 5 T-D 1 2 3 4 5 This cannot be select when surround back speakers are connected.
>> Specifications >> Advanced Setup >> Listening Modes >> Network Functions >>Basic Manual Troubleshooting | Supplementary Information, etc. ■ Internet radio service menus LINKS Internet Radio You can use internet radio services such as TuneIn Radio, Pandora, Deezer, and TIDAL by connecting this unit to a network that has an internet connection. • Services available may vary depending on the region. • Depending on the internet radio service, the user may need to register from their computer first.
>> Specifications >> Advanced Setup >> Listening Modes >> Network Functions >>Basic Manual Troubleshooting | Supplementary Information, etc. Spotify Spotify Connect play is possible by connecting this unit to the same network as a smart phone or tablet. • To play Spotify Connect, you need to install the Spotify application on your smartphone or tablet. You also need to create a Spotify premium account. • Refer to the following for Spotify settings: www.spotify.
>> Specifications >> Advanced Setup >> Listening Modes >> Network Functions >>Basic Manual Troubleshooting | Supplementary Information, etc. AirPlay® You can wirelessly enjoy the music files on an iPhone®, iPod touch®, or iPad® connected to the same access point as this unit. • Update the OS version on your iOS device to the latest version. • There may be some differences in the operations screens and how operations are performed on the iOS device depending on the iOS version.
>> Specifications >> Advanced Setup >> Listening Modes >> Network Functions >>Basic Manual Troubleshooting | Supplementary Information, etc. Music Server Overview Streaming play of music files stored on PCs or NAS devices connected to the same network as this unit is supported. • The network servers this unit is compatible with are those PCs with players installed that have the server functionality of Windows MediaR Player 11 or 12, or NAS that are compatible with home network functionality.
>> Specifications >> Advanced Setup >> Listening Modes >> Network Functions >>Basic Manual Troubleshooting | Supplementary Information, etc. and press Enter. 2. With the up and down cursors on the remote controller, select the Search folder and press Enter. There are the following 3 Search folders. • "Search by Artist": Select when searching by artist name. • "Search by Album": Select when searching by album name. • "Search by Track": Select when searching by track name. 3.
>> Specifications >> Advanced Setup >> Listening Modes >> Network Functions >>Basic Manual Troubleshooting | Supplementary Information, etc. Supplementary information for player functions Due to firmware (the software for the system) updates after you make your purchase or firmware changes during production of the product, there may be additions or changes to the features available compared to what is in the instruction manual.
>> Specifications >> Advanced Setup >> Listening Modes >> Network Functions >>Basic Manual Troubleshooting | Supplementary Information, etc. LINKS Troubleshooting Before starting the procedure Problems may be solved by simply turning the power on/ off or disconnecting/connecting the power cord, which is easier than working on the connection, setting and operating procedure. Try the simple measures on both the unit and the connected device.
>> Specifications >> Advanced Setup >> Listening Modes >> Network Functions >>Basic Manual Troubleshooting | Supplementary Information, etc. again. – If "AMP ERR" is displayed: It is possible that the amplifier circuits in the unit have malfunctioned. Wait for at least a minute and then turn the unit on again. If the same symptoms such as being unable to turn the unit on happen repeatedly, unplug the power cord from the wall outlet immediately and contact the dealer or our company's support.
>> Specifications >> Advanced Setup >> Listening Modes >> Network Functions >>Basic Manual Troubleshooting | Supplementary Information, etc. cannot be heard • Since it takes longer to identify the format of an HDMI signal than it does for other digital audio signals, audio output may not start immediately. Listening Modes • To enjoy digital surround playback, such as Dolby Digital, the audio signals need to pass through a connection via HDMI cable, digital coaxial cable, or digital optical cable.
>> Specifications >> Advanced Setup >> Listening Modes >> Network Functions >>Basic Manual Troubleshooting | Supplementary Information, etc. Video • Confirm that the connection between the output jack on the device and the input jack on this unit is correct. • Make sure that none of the connecting cables are bent, twisted, or damaged. • When the TV image is blurry or unclear, power code or connection cables of the unit may have interfered.
>> Specifications >> Advanced Setup >> Listening Modes >> Network Functions >>Basic Manual Troubleshooting | Supplementary Information, etc. BLUETOOTH function (for compatible models only) • Try plugging/unplugging the power of the unit and try turning on/off the BLUETOOTH wireless technology enabled device. Re-startup of the BLUETOOTH wireless technology enabled device may be effective. • The BLUETOOTH wireless technology enabled devices must support the A2DP profile.
>> Specifications >> Advanced Setup >> Listening Modes >> Network Functions >>Basic Manual Troubleshooting | Supplementary Information, etc. Functions" in the Advanced Manual. • When using a PC, only music files registered in the Windows MediaR Player library can be played. Wireless LAN Network (for compatible models only) ■ Playback stops while listening to music files on the network server • Make sure the network server is compatible with this unit.
>> Specifications >> Advanced Setup >> Listening Modes >> Network Functions >>Basic Manual Troubleshooting | Supplementary Information, etc. sunshine or inverter-type fluorescent lights. Relocate if necessary. • If the unit is installed in a rack or cabinet with coloredglass doors or if the doors are closed, the remote controller may not work reliably.
>> Specifications >> Advanced Setup >> Listening Modes >> Network Functions >>Basic Manual Troubleshooting | Supplementary Information, etc. reflected waves when a person crosses or approaches the space between the AV receiver and the wireless LAN device. • We assume no responsibility whatsoever for any damages resulting from the use of this apparatus except in the cases deemed acceptable under the applicable laws and regulations. • Operation in all environment is not guaranteed for wireless LAN.
>> Specifications >> Advanced Setup >> Listening Modes >> Network Functions >>Basic Manual Troubleshooting | Supplementary Information, etc. LINKS Supplementary Information Due to firmware (the software for the system) updates after you make your purchase or firmware changes during production of the product, there may be additions or changes to the settings and operation available compared to what is in the instruction manual.
>> Specifications >> Advanced Setup >> Listening Modes >> Network Functions >>Basic Manual Troubleshooting | Supplementary Information, etc. License and Trademark Manufactured under license from Dolby Laboratories. Dolby, Dolby Atmos, Dolby Surround, Dolby Vision and the double-D symbol are trademarks of Dolby Laboratories. For DTS patents, see http://patents.dts.com. Manufactured under license from DTS, Inc.
>> Specifications >> Advanced Setup >> Listening Modes >> Network Functions >>Basic Manual Troubleshooting | Supplementary Information, etc. technologies (e.g., THX Mode) which accurately translate movie soundtracks for home theater playback. Re-Equalization and the“Re-EQ”logo are trademarks of THX Ltd. DRC-R1.1 THX and the THX logo are trademarks of THX Ltd., registered in the U.S. and other countries. THX CERTIFIED ULTRA and the THX ULTRA application icon are trademarks of THX Ltd.
1-10-5 Yokoami, Sumida-ku, Tokyo 130-0015 Japan http://www.integraworldwide.com 18 Park Way, Upper Saddle River, N.J. 07458, U.S.A. Tel: 800-225-1946, 201-818-9200 Fax: 201-785-2650 http://www.integrahometheater.com Gutenbergstrasse 3, 82178 Puchheim, Germany Tel: +49-8142-4401-0 Fax: +49-8142-4208-213 http://www.integra.eu 302, Building 1, 20 North Chaling Rd., Xuhui District, Shanghai, China 200032, Tel: +86-21-52131366 Fax: +86-21-52130396 http://www.integra.com.