ASSEMBLY & OPERATION MANUAL RECORD SERIAL NUMBER HERE www.inspirefitness.com by Health In Motion LLC Feb.
TABLE OF CONTENTS Section Description……………………………………………………. Page Important Safety Instructions………………………………………. 1 Parts List…………………………………………………………………………. 2 Exploded Diagram………………………………………………………….. 3 Assembly Instructions……………………………………………………. 4 Decal Reference…………………………………………………………….. 13 Decal Placement……………………………………………………………… 14 General Maintenance Information…….…………………………… 15 Maintenance Schedule…….……………………………………………… 16 Limited Warranty……………………………………………………………..
IMPORTANT SAFETY INSTRUCTIONS Please read this entire manual and familiarize yourself with all decals and warnings before using this hyper extension. • WARNING! It is necessary to inspect this hyper extension regularly to maintain safety and proper function. Please use the maintenance schedule included towards the back of this manual. Immediately replace any and all defective or worn parts. See General Maintenance section for complete details.
PARTS & HARDWARE LIST Item # Description Part Number Quantity 1 Front Foot Tube Assembly GM582-200-001 1 2 Stabilizer Assembly GM582-100-001 PZ 1 3 Front Support Tube Assembly GM582-270-001PZ 1 4 Handle Assembly GM582-250-001PZ 1 5 Adjustment Tube Assembly GM582-230-001PZ 1 6 Pivot Tube Assembly GM582-210-001PZ 1 7 Lower Adjustment Tube Assembly GM582-220-001PZ 1 8 Upper Adjustment Tube Assembly GM582-240-001PZ 1 9 Leg Rest Assembly GM582-260-001PZ 1 10 Foot Roller
37 38 10 40 11 41 9 41 40 10 38 35 39 39 22 16 22 12 17 39 20 4 43 30 26 14 Page 3 20 12 35 13 20 20 37 29 34 5 3 24 6 31 26 36 32 39 12 25 21 11 1 12 39 7 28 32 12 39 33 39 39 21 8 29 27 30 29 39 21 21 29 2 28 29 27
1 12 39 21 39 2 Step 1 A Combine the Front Foot Tube Assembly (1) and the Stabilizer Assembly (2) using 2- Hex Bolts M12x95 (21), 4- Flat Washers ɸ12 (39), and 2- Lock Nuts M12 (12). Hand Tighten Only.
6 2 12 39 21 32 39 Step 2 Attach the Pivot Tube Assembly (6) to the Stabilizer Assembly (2) using 1- Hex Bolt M12x95 (21), 2- Flat Washers ɸ12 (39), and 1- Lock Nut M12 (12). Make sure the Hex Bolt M12x95 (21) goes through Spacer 2 (32) inside the Pivot Tube Assembly (6). TIGHTEN HARDWARE FROM THIS STEP ONLY.
6 7 26 Step 3 A Loosen the Pop-pin (26) and insert the Lower Adjustment Tube Assembly (7) into the Pivot Tube Assembly (6).
5 39 7 39 12 32 21 Step 4 Attach the Adjustment Tube Assembly (5) to the Lower Adjustment Tube Assembly (7) usinge 1- Hex Bolt M12x95 (21), 2- Flat Washers ɸ12 (39), and 1- Lock Nut M12 (12). Make sure the Hex Bolt M12x95 (21) goes through Spacer 2 (32) inside the Lower Adjustment Tube Assembly (7). TIGHTEN HARDWARE FROM THIS STEP ONLY.
37 38 10 40 41 41 40 10 38 37 9 Step 5 A Attach the Aluminum Cap (38), Foot Roller (10), Plastic Washer (40), and Foam Stopper (41) to the Leg Rest Assembly (9) using 1- Flathead Screw M10x25 (37). Repeat for both sides. TIGHTEN HARDWARE FROM THIS STEP ONLY.
9 30 29 8 5 33 36 Step 6 A Attach the Leg Rest Assembly (9) to the Upper Adjustment Tube Assembly (8) using 2- Hex Bolts M10x60 (33), 4- Flat Washers ɸ10 (29) and 2- Lock Nuts M10 (30) B Unscrew the Pop-pin and insert the Upper Adjustment Tube Assembly (8) into Adjustment Tube Assembly (5). Note: The Tightening Screw (36) needs to be loosened in order for the Upper Adjustment Tube Assembly (8) to go into the Adjustment Tube Assembly (5) TIGHTEN HARDWARE FROM THIS STEP ONLY.
3 12 39 39 21 1 Step 7 A Attach the Front Support Tube Assembly (3) to the Front Foot Tube Assembly (1) using 2- Hex Bolts M12x95 (21), 4- Flat Washers ɸ12 (39), and 2- Lock Nuts M12 (12). HAND TIGHTEN ONLY.
4 12 21 39 13 39 21 14 5 3 Step 8 A Attach the Handle Assembly (4) to the Adjustment Tube Assembly (5) using 2- Hex Bolts M12x95 (21), 4- Flat Washers ɸ12 (39), and 2- Lock Nuts M12 (12). B Attach the Handle Assembly (4) to the Front Support Tube Assembly (3) using 1- Hex Bolt M12x110 (13), 2- Flat Washers ɸ12 (39), and 1- Lock Nut M12 (12). Make sure the Hex Bolt M12x110 (13) goes through Spacer 1 (14) inside the Front Support Tube Assembly (3). TIGHTEN ALL HARDWARE FROM STEP 1, STEP 7 & STEP 8.
11 22 29 29 22 11 4 Default Orientation Step 9 A Attach the Back Pad Assembly (11) onto the Handle Assembly (4) using 2- Hex Bolts M10x25 (22) and 2- Flat Washers ɸ10 (29). Repeat for both sides. Note: Back Pads can be oriented in either direction. The default orientation is shown above. TIGHTEN HARDWARE NOW.
DECAL REFERENCE Page 13
DECAL PLACEMENT "Checklist" (on the reverse side) "Warning Label" "Warning, Pinch Point!" (Side of the plate) "Warning, Pinch Point!" Serial Number (Bottom of the Assembly) PAGE 14
GENERAL MAINTENANCE INFORMATION Warning: DO NOT place styrofoam or printed materials on the orthopedic pads. Over time, these may stick to the pads and mar the surface. Do not leave items sitting on the orthopedic pads, these pads have a special density that takes shape to objects and small objects will leave imprints in the surface that may take time to come out. • Regularly inspect product for loose hardware. • Do not use or store equipment outdoors.
MAINTENANCE SCHEDULE ROUTINE HOME MAINTENANCE Inspect: Links, Pull Pins, Spring Clips, Swivels, Weight Stack Pins WEEKLY Clean: Upholstery WEEKLY Inspect: Accessory Bars and Handles 3 MONTHS Inspect: All Decals 3 MONTHS Inspect: All Nuts and Bolts.
Warranty. This Warranty applies to Inspire Strength products manufactured or distributed by Health In Motion LLC. CONSUMER USE: LIMITED LIFETIME FRAME: Includes Frame and Welds LIMITED LIFETIME PARTS: Includes Upholstery, Hardware, etc. LIMITED LIFETIME MOVING PARTS: Includes Pulleys, Cables, etc. LIGHT-COMMERCIAL USE: LIMITED LIFETIME FRAME: Includes Frame and Welds 10 YEAR PARTS: Includes Upholstery, Hardware, etc. 10 YEAR MOVING PARTS: Includes Pulleys, Cables, etc.