INSTALLATION GUIDE Fixed-Position Wall Mount for TVs 40–70 in. NS-HTVMF0C Before using your new product, please read these instructions to prevent any damage.
Safety information and specifications CAUTION: IMPORTANT SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS - READ THE ENTIRE MANUAL PRIOR TO USE Maximum TV weight: 100 lbs. (45.3 kg) Screen size: 40 in. to 70 in. diagonal Overall dimensions (H × W ): 17.0 × 25.6 in. (43.2 × 65 cm) Wall-mount weight: 2.4 lb (1.1 kg) We’re here for you CAUTION: Do not use this product for any purpose not explicitly specified by Insignia. Improper installation may cause property damage or personal injury.
FIXED-POSITION WALL MOUNT FOR TVs 40-70 in. Tools needed You will need the following tools to assemble your new TV wall mount: ardware Socket wrench with 1/2 in. (13 mm) socket or adjustable wrench Edge-to-edge stud finder Pencil Awl Phillips screwdriver Level Hammer Drill 7/32 in. (5.5 mm) wood drill bit (for wood stud wall) OR Tape Measuring tape 3/8 in.
TV Hardware Bag Label 2 Hardware Qty. TV Standoff Label Hardware 2 7 3 4 M8 × 35 mm screw M6 × 12 mm screw 4 8 4 M8 × 16 mm screw 5 M8 × 20 mm screw M6/M8 washer Spacers 4 4 11 M6 × 35 mm screw 4 4 9 6 Qty. 2 5/16 in. × 2 3/4 in. lag bolt 4 12 Lag bolt washer 2 Concrete Installation Kit CMK1 (not included) Contact customer service at 1-800-359-5520 to have these additional parts shipped directly to you. C1 2 5/16 in. × 2 3/4 in.
FIXED-POSITION WALL MOUNT FOR TVs 40-70 in. Installation instructions STEP 1 - Determining whether your TV has a flat back or an irregular or obstructed back 1 Carefully place your TV screen face-down on a cushioned, clean surface to protect the screen from damages and scratches. 2 If your TV has a table-top stand attached, remove the stand. See the documentation that came with your TV for instructions. 3 Temporarily lay the TV brackets (1), oriented vertically, on the back of your TV.
STEP 2 - Select screws, washers, and spacers 1 Select the hardware for your TV (screws, washers, and spacers). A limited number of TVs come with mounting hardware included. (If there are screws that came with the TV, they are almost always in the holes on the back of the TV.) If you don't know the correct length of the mounting screws your TV requires, test various sizes by hand threading the screws.
FIXED-POSITION WALL MOUNT FOR TVs 40-70 in. STEP 3 - Option 1: Attaching the mounting hardware to TVs with a flat back 1 Align the left and right TV brackets (1) with the upper screw holes on the back of the TV. Make sure that the brackets are level. 2 Install washers (8) and screws (3, 4, or 5) into the holes in the back of the TV. 3 Install TV standoffs (2) in the lower screw holes on the back of the TV using washers (8) and screws (3, 4, or 5).
STEP 3 - Option 2: Attaching the mounting hardware to TVs with irregular or obstructed backs 1 Place spacers (9) over the screw holes on the back of the TV. 2 Align the left and right TV brackets (1) with the upper screw holes on the back of the TV. Make sure that the brackets are level. 3 Place washers (8) over the holes in the TV brackets. Insert screws (6 or 7) through the washers, TV brackets, and spacers.
FIXED-POSITION WALL MOUNT FOR TVs 40-70 in. STEP 4 - Determine wall-mount location Note: • For more detailed information on determining where to drill your holes, visit our online height-finder at: http://mf1.bestbuy.selectionassistant.com/index.php/heightfinder • Your TV should be high enough so your eyes are level with the middle of the screen. This is normally 40 to 60 in. from the ground.
STEP 5 - Option 1: Installing on a wood stud* wall Note: Any drywall covering the wall must not exceed 5/8 in. (16 mm). 1 Locate the stud. Verify the center of the stud with an edge-to-edge stud finder. 2 Align the center of the wall plate template (R) at the height (a + b - 1.5 in.) you determined in the previous step, make sure that it is level, then tape it to the wall. 3 Drill two pilot holes through the template to a depth of 3 in. (75 mm) using a 7/32 in. (5.
FIXED-POSITION WALL MOUNT FOR TVs 40-70 in. • DO NOT over-tighten the lag bolts (11). * Minimum wood stud size: common 2 x 4 in. (51 x 102 mm) nominal 11/2 x 31/2 in. (38 x 89 mm). * Minimum horizontal spacing between fasteners cannot be less than 16 in. (406 mm). Align the center of the template with the height mark (a+b) you made in step 4. 3 in. 75 mm) You’ll need Wall mount template Wall plate template (R) Wall plate (10) 7/32 in. wood drill bit 1/2 in.
STEP 5 - Option 2: Installing on a solid concrete or concrete block wall (requires Concrete Installation Kit CMK1) 1 2 3 4 CAUTION:To prevent property damage or personal injury, never drill into the mortar between the blocks. Mount the wall plate directly onto the concrete surface. Align the center of the wall plate template (R) at the height (a + b - 1.5 in.) you determined in the previous step, make sure that it is level, then tape it to the wall.
FIXED-POSITION WALL MOUNT FOR TVs 40-70 in. • DO NOT over-tighten the lag bolts (C1). . Align the center of the template with the height mark (a+b) you made in step 4. 3 in. (75 mm) C3 * Minimum solid concrete thickness: 8 in. (203mm) * Minimum concrete block size: 8 x 8 x 16 in. (203 x 203 x 406 mm). * Minimum horizontal spacing between fasteners cannot be less than 16 in. (406 mm). C1 C2 You’ll need Wall mount template Wall plate template (R) Level Wall plate (10) 3/8 in.
STEP 6 - Mounting the TV to the wall plate 1 Holding the TV with the top of the screen tilted toward the wall, slide the upper notches of the right and left TV brackets (1) over the upper lip of the wall plate (10). 2 Push the bottom of the TV toward the wall until the latch mechanism clicks into place. HEAVY! You will need assistance with this step. 14 www.insigniaproducts.
FIXED-POSITION WALL MOUNT FOR TVs 40-70 in. Removing the TV from the wall plate • Pull down and hold both release straps, then pull the bottom of the TV away from the wall and lift the assembly off the wall plate. HEAVY! You will need assistance with this step. www.insigniaproducts.
ONE-YEAR LIMITED WARRANTY Definitions: The Distributor* of Insignia branded products warrants to you, the original purchaser of this new Insignia-branded product (“Product”), that the Product shall be free of defects in the original manufacturer of the material or workmanship for a period of one (1) year from the date of your purchase of the Product (“Warranty Period”).
FIXED-POSITION WALL MOUNT FOR TVs 40-70 in. • • • • Consumables, including but not limited to batteries (i.e. AA, AAA, C etc.) Products where the factory applied serial number has been altered or removed Loss or Theft of this product or any part of the product Display panels containing up to three (3) pixel failures (dots that are dark or incorrectly illuminated) grouped in an area smaller than one tenth (1/10) of the display size or up to five (5) pixel failures throughout the display.
Part Number: 6907-302037 www.insigniaproducts.com 1-877-467-4289 (U.S. and Canada) or 01-800-926-3000 (Mexico) INSIGNIA is a trademark of Best Buy and its affiliated companies. Distributed by Best Buy Purchasing, LLC 7601 Penn Ave. South, Richfield, MN 55423 U.S.A. ©2020 Best Buy. All rights reserved.