InsideTNC IV001AS USER’S GUIDE
Copyright© 2000 Inside Teletcom Co.,Ltd. This installation guide is copyrighted. All rights reserved. This document may not, in whole or part, be copied, reproduced, reduced or translated by any means, either mechanical or electronic, without prior consent in writing from Inside Telnetcom Co., Ltd. The information in this manual has been carefully checked and is believed to be accurate. However, Inside Telnetcom Co., Ltd assumes no responsibility for any inaccuracies that may be contained in this manual.
FCC RF INTERFERENCE STATEMENT NOTE : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
- CONTENTS 1. Features of InsideTNC’s IV001AS ……………………………………………… - The Feature of GeForce2 MX/GTS System Requirement Driver and Software Support 2. Installation (Hardware) ……………………………………………………………… 3. Installation (Software) ………………………………………………………………… Method I. Plug& Play ………………………………………………………………………… Method II. Do it your self …………………………………………………………………… 4. Troubleshooting ……………………………………………………………………… APPENDIX * Table 1-1. Windows 95/98ME Resolution rate & Refresh rate- 32MB * Table 1-2.
1. The Feature of InsideTNC’s IV001AS Used nVIDIA’s GeForce2 MX/GTS GPU, Inside Telnetcom’s IV011A supports the advanced features, TwinView, a innovative dual display architecture, which doubles your desktop workspace using two space saving display and. DVC(Digital Vibrance Control) which provides crisp, bright visuals. IV011A(DREAM.
Driver and Software Supports - - Display Driver for Windows 95/98/ME Display Driver for Windows 2000, WindowsNT 4.0/3.5 OpenGL ICD for Windows 2000, Windows NT 4.0, Windows 95/98/ME Display Driver f for Linux, OS/2 Before Installation To avoid accidental electric chock, shut your computer down and unplug the power cord before staring the following procedures. Remember which cable go to which connectors. You may want to label your computer’s cable before disconnection them.
2. Installation (Hardware) 1. With the power off, remove your computer cover and locate on AGP slot. 2. Insert your card firmly into the slot. Card should be taken to press it evenly and snugly into its slot. Do not force! NOTICE. AGP slot is designed as a double structure in a different way from PCI slot. When DREAM.GRAPHICS is not inserted into its AGP slot snugly, your computer system can not work at all; therefore, you must set your board firmly into the slot.
3. Once you are certain that the card is installed properly in its slot, secure it to the PC frame with the screw you removed in step. Make sure the card does not lift out of the slot while tightening the bracket screw. Connect your monitor cable to the 15 pin-connectors on your computer. 4. Secure the cover and reboot your computer. Continue with the software installation for operating system in the following section.
3. Installation (Software) This section describes the software installation process for supported Windows. To install theGeForce2 MX driver 1. Start up Windows and log onto and account with administrator privileges. 2. Place the GeForce2 MX/GTS CDROM disk into your CD-ROM drive. When the installation window opens, choose the installation. 3. Follow the instructions that appear on your screen. 4. Restart your system at the prompt.
2. After Selecting Search for the best driver for your device(Recommended) from the following dialogue box, insert the Support CD into your CD-ROM drive. From the Specify the Location:, select E:\VGA\DRIVER\GeForce2 MX/GTS\Win9X , click Next. In this case, E:\ means CD-ROM drive.
3.Select The updated software [Recommended] InsideTNC GeForce2 MX/GTS and click Next. 4. When Windows driver file search for the device: InsdieTNC GeForce2 MX/GTS appears, click Next.
5. Copying files to Windows system folder should been completed. It may take a few seconds. 6. Click Finish to complete setup. 7. Click Yes to restart your computer.
Method II. Do It Yourself 1. In order to install the driver of Inside’s GeForce2 MX/GTS by yourself, Select Start > Setting > Control Panel > System Properties > Device manager > Display adapters > Standard PCI Graphics Adapters and click Properties in Windows95/98/ME.
2. From Standard PCI Graphics Adapter [VGA] Properties > Driver, click Update Driver… 3. Select Specify the location of the driver [Advanced] and click Next.
4. From the select Search for a better driver than the one your device is using now. [Recommended] and then check the Specify a location E:\\VGA\DRIVER\GeForce2 MX/GTS\Win9X. and then click Next. In this case, E: \ means CD-Rom drive. 5. When Windows driver file search for the device: InsdieTNC GeForce2 MX/GTS appears, click Next.
6. Copying files to Windows system folder should been completed. It may take a few seconds. 7. Click Finish to complete setup. 8. . Click Yes to restart your computer.
4. Troubleshooting The graphic board users queried as follow: Question 1 : ‘Version Crash’ message appeared and Windows asked me “Do you save ex-file?” during installing driver. How can I answer to solve it? Answer 1 : When we change the graphic board, the same file name exists in the System folder in Windows. . In this case, selecting No is recommended. Question 2 : Even driver installation was completed, 16 color was selected only.
APPENDIX *Table 1-1.