User's Manual

ManualsBrandsInpeco Spa a Socio Uni ManualsElectronicsRadio Frequency Identification Device for Sample Carriers

Table Of Contents

Security
- General Security
  - Security Notes
  - Safety Labels
- Environmental and power specifications

APTIO - Operations Manual 2-1

799.007.203.0— February 2011

Section 2 Security

Security

1. General Security, Section 2-2

a. Security Notes, Section 2-2S

b. Safety Labels, Section 2-3

2. Environmental and power specifications, Section 2-6

a. Environmental conditions, Section 2-6

b. Power requirements, Section 2-6

c. Compressed Air Requirements, Section 2-6

d. Manufacturer, Section 2-7

e. Waste Disposal, Section 2-7

f. Hazardous substances, Section 2-7

g. Installation Specifications, Section 2-8

h. Bar Code Reader Lasers, Section 2-8

i. Moving Parts, Section 2-8

j. Equipment Protection, Section 2-8

k. FCC warning statements, Section 2-8

Summary of content (8 pages)

PAGE 1
Section 2 Security Security 1. General Security, Section 2-2 a. Security Notes, Section 2-2S b. Safety Labels, Section 2-3 2. Environmental and power specifications, Section 2-6 a. Environmental conditions, Section 2-6 b. Power requirements, Section 2-6 c. Compressed Air Requirements, Section 2-6 d. Manufacturer, Section 2-7 e. Waste Disposal, Section 2-7 f. Hazardous substances, Section 2-7 g. Installation Specifications, Section 2-8 h. Bar Code Reader Lasers, Section 2-8 i.
PAGE 2
Security Section 2 General Security Personnel operating the automation must be proficient in its operation, maintenance, and procedures. To ensure safety, follow basic precautions. Security Notes Warnings, cautions, and notes are included throughout this manual to emphasize important instructions. WARNING: Defined as a physical, mechanical, or procedural condition that could result in moderate to serious personal injury.
PAGE 3
Section 2 Security Safety Labels The following labels are affixed to the Automation System to alert the operator to safety considerations. Icon Description The operator should refer to the FlexLab 3.6 Operations Manual before performing procedures on the Automation System. Indicates the Automation System l was manufactured in the European Union in compliance with European regulations. Manufacturing location. Manufactured by Inpeco S.p.A. Segrate (MI) - Italy in Borgone di Susa Factory Plan.
PAGE 4
Security Section 2 Table Section 2.1: Labels Icon Description Identifies an area where operators can be exposed to moving parts. Be careful around these parts when performing diagnostics and maintenance operations with safety shield and covers removed. Identifies an activity that may present a safety-related hazard and advises the operator to consult the associated caution or warning instructions provided. Identifies an activity or area where operators may be exposed to potentially infectious material.
PAGE 5
Section 2 Security Table Section 2.1: Labels Icon Description Avoid eye exposure to laser light. Do not stare into beam. Warns against direct viewing of the beam or reflections from the beam. • Input Output Module, Centrifuge Module and Storage and Retrieval Module cover lids should be opened completely to engage the locking mechanism. • When closing the Input Output Module, Centrifuge Module and Storage and Retrieval Module safety shields, pull out the lock and lower the safety shield.
PAGE 6
Security Section 2 Environmental and power specifications Environmental conditions Description Value Operating altitude up to 2000 meters above sea level Operating temperature range 16° to 30° C Operating humidity Max 80% at 30°C Overvoltage Category I Pollution Degree 2 Table 2.
PAGE 7
Section 2 Security Manufacturer This equipment is manufactured by Inpeco S.p.A. in Borgone di Susa factory plant. www.inpeco.com Inpeco S.p.A Via G. Di Vittorio, 11 - Segrate (MI) - ITALY Phone +39 (02) 36681300 - Fax +39 (02) 36681399. Viale Europa, 14. Borgone di Susa (TO) - ITALY Phone +39 (02) 36681400 - Fax +39 (02) 36681499. Waste Disposal Dispose of all waste produced during the workcell operation according to local, state, and country regulations.
PAGE 8
Security Section 2 Installation Specifications The FlexLab 3.6 Automation system must be installed by a qualified Inpeco representative. System installation includes a complete checkout to ensure the equipment is fully operational. This equipment is intended only for internal use. Bar Code Reader Lasers The Automation system has one or more Bar Code Readers emitting laser beams. All bar code reader laser beams are protected by means of a metallic shield.