User's Manual

ManualsBrandsInovonics Wireless ManualsElectronicstransmitter

F202_V1.FM rev 1.10 1/27/00

Page 1

Scope of Manual:

This Inovonics manual contains additional installation and servicing information that is not available in the accompanying primary instal-

lation manual:

ESL 560 Series Wireless Smoke Detector Installation Instructions

. This secondary manual is chiefly concerned with transmitter program-

ming and servicing the detector in response to trouble indications at the control panel.

Typical average standby current......................................................38.5µA

Typical peak alarm current..............................................................91.1mA

The FA202 Wireless Smoke Detector, built upon photoelectric Sentrol/ESL

technology, continually monitors its own sensitivity and operational status.

If it detects a Low Battery condition or is in need of cleaning, it transmits a

Low Battery signal that should be interpreted as a “Maintenance Needed”

trouble condition at the control panel. If the unit is in need of cleaning, it can

be serviced on-site by replacing its Smoke Chamber. Two 3 volt lithium bat-

teries, supplied with the product, provide at least one year of operation.

HIS

EQUIPMENT

SHOULD

INSTALLED

ACCORDANCE

WITH

THE

ATIONAL

IRE

ROTECTION

SSOCIATION

’

TANDARD

72.

(National Fire Protection Association, Batterymarch Park, Quincy, MA 02269)

1. Locate the transmitter programming pins by disassembling the detector

as follows (refer to Figures 4 through 7 in the ESL 560 instructions):

a. Remove the red dust cover containing the batteries from the smoke

detector.

b. With the smoke detector facing you, remove the detector from its

Mounting Base by twisting the detector about 15 degrees counter-

clockwise with respect to the Mounting Base.

c. Remove the Detector Cap by first sliding a flatblade screwdriver

part way into the slot on the side of the Detector Cap. Now, gently

push the handle down while twisting the Detector Cap counter-

clockwise with respect to the Detector Lid.

d. Remove the Detector Lid from the Body by pushing down on the

Smoke Chamber while pulling up on the bottom of the Lid (see Fig-

ure A).

e. Remove the Battery Cover that encloses the Battery Compartment

by pushing on the area marked

OPEN

f. Take the batteries out of the red dust cover holder and load them

into the Battery Compartment. Make sure to observe battery polar-

ity and that the battery removal ribbon rests under the batteries.

g. Refer to Figure B to locate the programming pins on the transmitter

board.

2. Using an appropriate Inovonics programming device, set the program-

ming options as follows:

• External Switch Type: Normally Closed

• EOL Resistor: No

• Use Internal Contact: No

• Check-in Time: 60 seconds

Note: These also are the factory default programming options. Some pro-

gramming devices like the FA422 Receiver can place an Identification Num-

ber into a transmitter without changing the default settings.

3. When prompted by the programming device to plug in the transmitter,

connect the programming cable to the 3-pin header. (Orientation of the

cable with respect to the 3-pin header is not important; both outside pins

on the 3-pin header are at ground potential.)

4. Press the Reset button on the transmitter.

When programming is complete, disconnect the cable, test the detector per

the Wireless Sensitivity Test Procedure (on the back of this sheet), and reas-

semble the smoke detector.

FA202 Current Draw Specifications

(Supersedes Sentrol ESL 560 specifications)

FA202 Wireless Smoke Detector

with CleanMe™ Signaling

FA202 Wireless Smoke Detector

with CleanMe™ Signaling

Programming Procedure

Figure A: Removing the Detector Lid

3-pin programming header

Reset button

CleanM e

disabled position

CleanM e

enabled position

Figure B: Transmitter Board Features

FA202

Installation

InstallationInstallation

Installation

Instructions

InstructionsInstructions

Instructions

900MHz

Frequency Agile

Technology

Summary of content (3 pages)

PAGE 1
Installation Instructions FA202 900MHz Frequency Agile® Technology Scope of Manual: This Inovonics manual contains additional installation and servicing information that is not available in the accompanying primary installation manual: ESL 560 Series Wireless Smoke Detector Installation Instructions. This secondary manual is chiefly concerned with transmitter programming and servicing the detector in response to trouble indications at the control panel.
PAGE 2
FA202 Wireless Sensitivity Test Procedure The FA202 should be tested upon initial programming and each time the Smoke Chamber is changed or the batteries are replaced. To make wireless signals from the detector cause an alarm or trouble indication at the control panel, receiver and panel programming must be completed prior to this test. If this has not been done, do so now. To test the detector, follow the procedure described under the Testing the Detector Sensitivity section in the ESL 560 instructions.
PAGE 3
Warranty & Disclaimer Inovonics Corporation ("Inovonics") warrants its products ("Product" or "Products") to conform to its own specifications and to be free of defects in materials and workmanship under normal use for a period of twenty-four (24) months from the date of manufacture. Within the warranty period Inovonics Corporation will repair or replace, at its option, all or any part of the warrantied product. Inovonics will not be responsible for dismantling and/or reinstallation charges.