User's Manual

ManualsBrandsInovonics Wireless ManualsElectronicsANALOG VOICE BELTPACK

QSR Performance Solutions Drive Thru System - Installation Instructions

What Is Included

1 — Base Station w/ 13.5 VDC power adaptor

1 — Programming station w/ 18” cable

1 — Microphone for inbound audio

1 — Speaker for outbound audio

1 Lot — Acoustic foam for speaker post

Varies Per Order — Belt-packs w/ pouch

1 — Battery per Belt-Pack (w/1 additional battery when 4 or more belt-packs are ordered)

Varies Per Order — Headsets (1 per belt-pack)

1 — Battery charger w/ 5 VDC power adaptor

What Is Not Included

• Cable to connect Base to speaker post equipment (3 separately jacketed, shielded, twisted pairs,

minimum 20 gauge stranded)

• Vehicle detection loop

• Optional grill speaker (8 ohms)

• Speaker post

• Conduit from inside restaurant to speaker post

• Miscellaneous hardware

• Tools

Installation Steps

1. Begin charging batteries prior to installing system

2. Determine best location for Base

• Needs electrical outlet (power adaptor has 6 foot cable)

• Maintain 3 feet clearance from large metal objects and electrical or electronic equipment

• Relative close proximity to drive thru booth(s) but avoid installing where base cannot be ser-

viced without interrupting normal business operations

• Be mindful of where conduit to speaker post terminates inside

• Programming station connects to base with 18” cable and needs to be at a height and location

that is accessible to restaurant employees

3. Install cabling from speaker post to Base location. 3 individually shielded, jacketed, twisted pairs, mini-

mum 20 gauge stranded.

4. Mount Base and connect cables (keep power cable and transformer at least 6 inches from left side of

Base)

5. Mount programming station within 18” of Base, and at an accessible height and connect cable

6. Mount vehicle detector and connect to Base, and to cable feeding to loop at speaker post

7. Install speaker and microphone in speaker post and connect cables, including connection to vehicle

detector loop. Solder all splices.

• IMPORTANT! Speaker and microphone inside of speaker post MUST be acoustically and me-

chanically isolated from each other AND the speaker post with foam rubber or an acoustic

dampening material to insure quality audio performance.

• In a typical speaker post the microphone would be mounted in the top section, closer to the

person placing the order. The speaker should be at least 2 feet away from the microphone,

typically mounted lower.

Summary of content (6 pages)

PAGE 1
QSR Performance Solutions Drive Thru System - Installation Instructions What Is Included 1 — Base Station w/ 13.
PAGE 2
Installation Steps — cont. 8. Make sure jumpers in Base are configured to match your installation (see Base Station Controls diagram) • J1 & J2 — Separate speaker & mic or one device serving as both • J4 — Detection type: closure or pulse • J5 — Full-duplex or Standard (half-duplex) • J6 — Full-duplex click suppression 9. Turn on power to base 10. Insert batteries in belt-packs and program per instructions on programming station 11.
PAGE 3
Power Switch Used to turn power to base off & on. Turn off to enable optional wired backup if one is installed. Channel Indicators Indicates which one of the eight channel frequencies is being used Power Indicator Lights when power is applied to base. Talk Indicator Lights when the Talk button is pressed on a belt-pack Day / Night Volume Switch Day position enables DAY outgoing volume control. Night position enables NIGHT outgoing volume control.
PAGE 4
Individual volume controls for grill speaker Power switch Configures outside speaker and mic for full or half duplex Jump pins 1 & 2 for airswitch detector. Jump pins 2 & 3 for sodar or loop detector Jump pins 1 & 2 to designate base as Lane 1. Jump pins 2 & 3 to designate base as Lane 2. Use to change frequency of base. Frequencies 1 8 with J3 set to Lane 1. Frequencies 9 - 16 with J3 set to Lane 2.
PAGE 5
Base Connection Terminal Power Adaptor Programming Station Normally Open Loop Loop Detector Grill Speaker (optional) Speaker Post Vehicle Detector Loop Do not terminate shield at microphone end QSR Performance Solutions - Connections To Base
PAGE 6
QSR Performance Solutions Drive Thru - Belt-Pack 1 2 3 4 5 6 7 8 9 10 11 Bottom View 1. Page Press to talk to the other headsets without being heard at the speaker post • Belt-packs can be programmed for Page Monitor Mode, they will only hear communication from other belt-packs that are using the Page button and will not hear communication to or from the speaker post • To program a belt-pack for Page Monitor Mode, hold Page button down while powering the headset on.