Installation Instructions

ManualsBrandsInnovere Medical ManualsElectronicsRadio Module for Audio and Data

CONFIDENTIAL

Page 1 of 3

DOC-850, SOP-01-1: Quality Document Template, Ver. 3

Once printed, this document becomes UNCONTROLLED. Please verify latest revision before each use.

DOC-9, SOP-01-1: Quality Document Template, Ver. 3

1. PURPOSE

The WMODLP is a direct sequence spread spectrum transceiver module designed to be used in the 2.4

GHz ISM band. This module is for internal use only and is not sold as a device on the market. The

WMODLP module is integrated into the Audio Pathway System by Innovere.

2. REGULATORY INFORMATION

The integrator is responsible for testing their end-product for any additional compliance requirements with

this module installed. Published FCC Module integration and RF Exposure guidance as well as label

requirements should be followed in the end product. As the module does not have a RF Shield, Spurious

radiated emission should be evaluated per Module integration guidance.

The end product with this module may be subject to some other form of authorization or testing

requirements, e.g. FCC part 15 and ICES-003 unintentional emission test requirement. It is the

integrator’s responsibility to comply with all applicable rules and be properly authorized.

Any changes or modifications not expressly approved by the party responsible for compliance could void

the user’s authority to operate the equipment.

2.1. Regulatory labelling

The radio module will be labelled with the following information:

FCC ID: 2ATDA –WMODLP6

IC: 25063-WMODLP6

This label is valid for the following module variants:

Antenna

Maximum

gain

Firmware

power

setting

Number of

channels

F-style trace antenna (link) +3.3 dBi <= 0dBm 1 – 17

U.FL sticker antenna (FXP70.07.0053A) +1.1 dBi <= 0dBm 1 – 17

If the FCC ID and IC number is not visible when WMODLP is installed inside a host device, then the

host device must contain the FCC ID number with the statement such as the following:

Contains

FCC ID: 2ATDA –WMODLP6

IC: 25063-WMODLP6

2.2. FCC regulator statements

This device complies with Part 15.247 of the FCC unlicensed transmitter rules.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two

conditions:

(1) This device may not cause harmful interference

(2) This device must accept any interference received, including interference that may cause

undesired operation.

REPORT

Document Title Report No.

SOP

Wireless Module Manual

Summary of content (3 pages)

PAGE 1
REPORT Document Title SOP-23-2: Wireless Module Manual Report No. 1. PURPOSE The WMODLP is a direct sequence spread spectrum transceiver module designed to be used in the 2.4 GHz ISM band. This module is for internal use only and is not sold as a device on the market. The WMODLP module is integrated into the Audio Pathway System by Innovere. 2. REGULATORY INFORMATION The integrator is responsible for testing their end-product for any additional compliance requirements with this module installed.
PAGE 2
.3. IC regulator statements This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence.
PAGE 3
5. PROGRAMMING The Purepath Wireless Configurator software is used to generate and load the wireless module configuration files used in the Innovere system. For regulatory testing, the module can be loaded with various regulatory test images using the Purepath Wireless Commander software. The wireless module is programmed by using a Purepath Wireless Audio EB evaluation board and a CC debugger. 6. SOFTWARE CONTROL The CC8530 on the Innovere Wireless Module is configured in host control mode.