SENTINEL™ Tracking Tag FAP5015-025 FAP5015-027 User Manual Innovative Wireless Technologies, Inc. 1100 Main Street Lynchburg, VA 24504 Phone: 434-316-5230 (United States) Fax: 434-316-5232 (United States) www.iwtwireless.com ©2017 Innovative Wireless Technologies, Inc. Not to be reprinted, reproduced or distributed in any form without the written permission of Innovative Wireless Technologies, Inc.
Table of Contents 1.0 PRODUCT OVERVIEW .................................................................................................... 2 2.0 SAFETY INFORMATION .................................................................................................. 3 2.1 MSHA APPROVAL ................................................................................................................... 3 2.2 PROXIMITY TO BLASTING COMPONENTS .........................................................................
1.0 PRODUCT OVERVIEW The SENTINEL™ Tracking Tag is a self-contained, battery-powered device that provides tracking capability within IWT’s ad-hoc wireless digital mesh network. The small and lightweight Tracking Tag is compatible with both the SENTINEL™ and ACCOLADE® Wireless Mesh systems. The Tracking Tag sends network health and status information to the dispatch station including Tag ID, battery level, emergency state, and tracking information.
2.0 SAFETY INFORMATION IMPORTANT! READ BEFORE OPERATING THE SENTINEL™ TRACKING TAG. This section contains important information on the safe operation of the SENTINEL™ Tracking Tag. 2.1 MSHA APPROVAL This device has been evaluated by the Mine Safety and Health Administration (MSHA) per Title 30 Code of Federal Regulations Part 23.
2.3 PART 15 OF FEDERAL COMMUNICATIONS COMMISSION (FCC) RULES COMPLIANCE Changes or modifications to this unit not expressly approved by Innovative Wireless Technologies, Inc., (IWT) may void the user’s authority to operate this equipment. This device complies with Part 15 of FCC Rules. Operation is subject to the following two conditions: 1) This device may not cause harmful interference. 2) This device must accept any interference received, including interference that may cause undesired operation.
3.0 SPECIFICATIONS 3.1 SPECIFICATIONS FOR FAP5015-025 PERSONNEL TRACKING TAG (Typical unless otherwise specified) Operating System Compatibility Operating Frequency Operating Temperature Operating Life RF Transmit Power Communications Range1 SENTINEL™ and ACCOLADE® Systems 902 to 928 MHz -20C to +70C 4 months @ 30-second update rate +22 dBm Self-forming mesh network Up to 1,000 feet Physcial Dimensions Weight Enclosure Antenna Power 3.69” x 2.44” x 1.25” 3.5 oz.
4.0 OPERATING INSTRUCTIONS 4.1 POWER The SENTINEL™ Tracking Tag requires three AA alkaline batteries. Use of other battery chemistries is not allowed. For applications requiring MSHA Intrinsic Safety approval, only the cells listed in Section 2.1 may be used, and batteries must be replaced in fresh air. To turn the Tracking Tag on, insert three AA batteries. Device will automatically turn on. There is no on/off button. 4.1.
Figure 2 - Remove screws with Phillips screwdriver Figure 3 - Carefully slide out interior tray Revised: 9/12/2017 Proprietary and Confidential 5520-16-0281 Rev: C Page 7 of 15
Figure 4 - Replace batteries and note proper polarity Enclosure gasket Figure 5 - Ensure gasket is undamaged and in place Revised: 9/12/2017 Proprietary and Confidential 5520-16-0281 Rev: C Page 8 of 15
Gasket on screw Figure 6 – Replace cover and tighten screws. Ensure the gasket is on the screw before inserting. 4.1.2 Replacing Batteries of FAP5015-027 Asset Tag To insert or replace batteries: Open enclosure by unscrewing the four captive cover screw on the back/bottom side of the enclosure. Remove Tracking Tag assembly from external enclosure. Follow battery replacement instructions in section 4.1.1. Place Tracking Tag assembly into foam insert in top side of enclosure.
Figure 7 - External enclosure is held together by four captive screws inserted at the back of the enclosure. Flat side of Tracking Tag assembly Figure 8 - Remove Tracking Tag assembly from external enclosure to replace batteries.
4.1.3 Battery Life The battery life ranges between 4 and 12 months depending on the user application. The Personnel version of the Tracking Tag (-025) operates for 4 months @ a 30-second update interval, and the Asset version of the Tracking Tag (-027) operates for 12 months @ a 4-minute update interval. 4.2 LED STATUS INDICATOR The Tracking Tag includes an LED status indicator with distinct blink patterns to provide local feedback to the user. The LED indicates network status and basic battery level.
4.3 PUSHBUTTON The Tracking Tag includes an orange multi-purpose pushbutton. In the Personnel version of the Tracking Tag (-025), this button is configured to generate an alert for the dispatcher in the event of an emergency condition. It is also used for initiating programming modes for configuration updates to the device. Pushbutton Figure 10 - Tracking Tag Pushbutton 4.4 CARRY POUCH FOR PERSONNEL TRACKING (FAP5015-025) A Custom Carry Pouch is available as a separate accessory for the Tracking Tag.
Belt Loop with Snaps Figure 12 - Carry Pouch Side View The top and bottom of the Carry Pouch have openings for easy access to the pushbutton and LED on top, and the Node ID on the bottom.
4.5 EXTERNAL ENCLOSURE FOR VEHICLE MOUNTING OR ASSET TRACKING (FAP5015-027) The FAA9100-310 Enclosure Assembly is available as a separate accessory for the Tracking Tag. For applications requiring MSHA Intrinsic Safety approval, the FAA9100-310 Enclosure Assembly is required when mounting the Tracking Tag to a vehicle or using the Tag to track material/assets (see Section 2.1).
