WI-FI BT ADD-ON-CARD USER MANUAL Installation guide and user manual for IOT Card, Wi-Fi+BT, 2.
WI-FI BT ADD-ON-CARD USER MANUAL CONTENT 1. Product Description ......................................................................................................................................... 3 2. Technical Specifications ................................................................................................................................. 4 3. Card descriptions .........................................................................................................................
WI-FI BT ADD-ON-CARD USER MANUAL 1. Product Description This Wi-Fi BT IOT add-on card is a network connectivity module that can be plugged into an IOT host. The edge connector pinouts are as per IOT card specifications i.e., a total of 38 pin gold fingers with each side having 19 pins as per standard signal pinouts for IOT host interfacing. This module is built on Qualcomm’s QCA9377-3 which is a single-die wireless local area network (WLAN) and Bluetooth (BT) combination solution to support 1 × 1 IEEE 802.
WI-FI BT ADD-ON-CARD USER MANUAL 2. Technical Specifications Item Description Product Name IOT Card, WiFi+BT, 2.4/5GHz Product part number 6001223 Chipset Qualcomm QCA9377-3 Wi-Fi Wi-Fi Certified- a/b/g/n/ac, WPA, WPA2 Bluetooth BT4.2 (BDR+EDR) and BLE IOT edge connector Interfaces As per 38 pin IOT card specification (uses 3.3V for power, 1.8V for IO, SDIO & UART for communication). RPSMA female type for antenna connection. 3.3V ( at 859mA max ) input from IOT gateway (host).
WI-FI BT ADD-ON-CARD USER MANUAL 3.
WI-FI BT ADD-ON-CARD USER MANUAL 4. Installation /Setup guide (using FX30 as an example IOT host gateway) Step 1: Open the cover plate of the FX30 module. Step 2: Insert the WBAC card in the IoT slot as shown in figure1: Figure 1: Module Insertion Step 3: Close the cover plate as shown in figure 2. And put the screws. Figure 2: Fixing Cover Plate Step 4: Insert washer and nut to the WBAC SMA connector as shown in figure 3.
WI-FI BT ADD-ON-CARD USER MANUAL Figure 3: Washer & Nut threading Step 5: Fix the antenna as shown in the figure 4. Figure 4: Module with Antenna Step 6: Power on the Fx30 module and connect the USB cable to the FX30 module.
WI-FI BT ADD-ON-CARD USER MANUAL Step 7: Open putty, set SSH mode, type 192.168.2.2 and port as 22 and login. Next when putty console opens, type login as ‘root’ and leave the password empty. Press enter. 5. Enabling Wi-Fi 5.1. Station/client mode: After step 7 mentioned above, ./13 ./42 To set the router name and password to which this device has to connect, type : vi /etc/wpa_supplicant.conf 'a' for edit, 'esc' for coming out of editting mode and ':wq' for save and exit. ./wifi.
WI-FI BT ADD-ON-CARD USER MANUAL 6. Enabling Bluetooth Type the following commands for Bluetooth After step 7 mentioned above, ./13 ./42 btproperty & btapp gap_menu enable Now you can enable Bluetooth on your testing phone and check for ‘MDM_Flouride’ and connect to it. Type ‘yes’ in putty console when asked whether to connection requested can be accepted. 7. Enabling BLE Type the following commands for BLE After step 7 mentioned above, ./13 .
WI-FI BT ADD-ON-CARD USER MANUAL 8. Revision history Rev Date Description Author v0p1 21-Aug-2018 Initial draft version Sudeendra V0p2 07-Dec-2018 Updated version with Prajwal more details added on the product specification table and instruction added for BLE. Approval Ganesan Ganesan Card description diagram added. Tablet of content added Document format updated. Revision history table, Introduction added.
WI-FI BT ADD-ON-CARD USER MANUAL 9. Regulatory declarations FCC Product name: IOT Card, WiFi+BT, 2.4/5GHz Model name: 6001223 FCC ID: 2ARZI-IWB6001223 This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Statement This device complies with part 15 of the FCC Rules.
WI-FI BT ADD-ON-CARD USER MANUAL If the FCC identification number is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module.
WI-FI BT ADD-ON-CARD USER MANUAL IC PMN: IOT Card, WiFi+BT, 2.4/5GHz HVIN: 6001223 IC: 24585-6001223 IC Warning This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) This device must accept any interference, including interference that may cause undesired operation of the device. The modular can be installed or integrated in mobile or fix devices only.
WI-FI BT ADD-ON-CARD USER MANUAL appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement Le modular peut être installé ou intégré dans un mobile ou réparer une seule chose installation dans n’importe quel appareil portable.
WI-FI BT ADD-ON-CARD USER MANUAL CE Product name: IOT Card, WiFi+BT, 2.4/5GHz Model: 6001223 Input: 3.3V 859mA max Powered by IOT host Manufacturer: Innominds software Inc Address: 2055 Junction Avenue, Suite 122, San Jose CA 95131 USA Made in India CE Maintenance 1. EUT Operating temperature range: -30° C to 75° C. 2. Ratings:Input 1.8V and 3.3V (Powered by IOT host) 3. The device complies with RF specifications when the device used at 20mm from your body.