SN10-12 SIGFOX Module User Guide and Product Specification Model Name SN10-12 Project code Description SIGFOX module Version 1.
SN10-12 REV 1.0 9/12/2017 Revision History Revision Released Date Comments/Remark Author 0.1 2017/03/14 Initial release Iestyn Chen 0.2 2017/03/17 Update with RX performance spec. Iestyn Chen 0.3 2017/03/24 Add module layout guide and appendix section Iestyn Chen 0.4 2017/03/29 Update RX value, reflow profile, and section 5.3 Iestyn Chen typo 0.5 2017/06/05 Update reference circuit 0.6 2017/07/11 Update RCZ4 related information and add Iestyn Chen module photo 0.
SN10-12 REV 1.0 9/12/2017 TABLE OF CONTENT 1. INTRODUCTION .......................................................................................................... 4 2. PIN MAP AND SIGNAL DESCRIPTION ......................................................................... 5 3. ELECTRICAL CHARACTERISTICS ............................................................................... 6 4. RF CHARACTERISTICS ................................................................................................
SN10-12 REV 1.0 9/12/2017 1. Introduction The SN10-12 is a SIGFOX verified and FCC, ACMA approved transceiver module which complies with SIGFOX network specifications. It is based on NXP OL2385 chip which is a Sub-GHz wireless SoC transceiver. 1.1. Key Features • • High performance low power RISC micro-controller Memory • • • • • • • • • • • 32kB EROM 7kB RAM Ultra Narrow Band Radio • Frequency Band RCZ2: 902.1375-904.6625MHz RCZ4: 920.1375MHz-922.
SN10-12 REV 1.0 9/12/2017 2.
SN10-12 REV 1.0 9/12/2017 3. ELECTRICAL CHARACTERISTICS 3.1 Absolute Maximum Rating PARAMETER Storage temperature range Supply voltage Maximum RX input level without damage CONDITIONS VDD MIN –55 -0.3 TYP MAX 150 3.6 10 UNIT °C V dBm MIN –40 3.3 TYP 25 MAX 85 3.6 UNIT °C V MIN TYP MAX UNIT 3.2 Recommended Operating Range PARAMETER Operating temperature range Operating supply voltage CONDITIONS 3.
SN10-12 REV 1.0 9/12/2017 4. RF Characteristics PARAMETER Center Frequency PARAMETER Antenna port impedance Model SN10-12 CONDITIONS UNIT MHz Frequency Band RCZ2: 902.1375-904.6625MHz RCZ4: 920.1375MHz-922.6625MHz MIN TYP MAX 50 UNIT Ω Note RCZ2 RCZ4 Note TX Characteristics Following characteristics are valid for conditions as follows (unless otherwise specified) Tamb = -40 °C to 85 °C, VDD = 3.3 V to 3.6 V, TCXO = 27.
SN10-12 REV 1.0 9/12/2017 5. SMT Solder Reflow Recommendation Note: Allowable reflow soldering times: 2 times base on recommended reflow profile.
SN10-12 REV 1.0 9/12/2017 6. SW information and User Guide SW information The SIGFOX software driver supports MCUs. These MCUs are a subset of the MCUs supported by the Kinetis Software Development Kit (KSDK) layer. This SW driver is built on the Analog Middleware Layer (AML), which creates an API abstraction layer for the desired Software Development Kit (SDK). The current implementation includes abstractions for KSDK 2.0 and S32 SDK.
SN10-12 REV 1.0 9/12/2017 Setting up the command line interface Figure 1 1) Stack the SN10-1x EVB on top of the KL25Z host boards to connect the SPI interface, 2) Connect the host board Open SDA to the PC with an USB cable, 3) KL25Z will pop up as a mass storage device. Open the folder and copy spi_sigfox_demo.srec to the folder. (ask innocomm for spi_sigfox_demo.srec), 4) Start a terminal emulator (e.g.
SN10-12 REV 1.
SN10-12 REV 1.0 9/12/2017 7.
SN10-12 REV 1.0 9/12/2017 Federal Communication Commission Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
SN10-12 REV 1.0 9/12/2017 Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
