SN10-12 SIGFOX Module User Manual FCC ID: YAISN10-12 Model Name SN10-12 Project code Description SIGFOX module Version 0.
SN10-12 7/12/2017 REV 0.5 Revision History Revision Released Date Comments/Remark Author 0.1 2017/03/14 Initial release Iestyn Chen 0.2 2017/03/17 Update with RX performance spec. Iestyn Chen 0.3 2017/03/24 Add module layout guide and appendix section Iestyn Chen 0.4 2017/03/29 Update RX value, reflow profile Iestyn Chen 0.5 2017/05/26 Modify FCC Interference Statement Keller Lin ® 2017 InnoComm Mobile Technology Corp.
SN10-12 7/12/2017 REV 0.5 TABLE OF CONTENT 1. INTRODUCTION ......................................................................................... 4 1.1. KEY FEATURES............................................................................................................. 4 2.ELECTRICAL CHARACETRISTICS ............................................................. 5 2.1 RECOMMENDED OPERATING RANGE .................................................................................... 5 2.
SN10-12 7/12/2017 REV 0.5 1. Introduction The IoT presents a different set of communications challenges to those faced by the conventional internet or cellular networks. Unlike cellphones and computers, IoT devices do not need to transfer large amounts of data. However, requirements for battery life and hardware cost are much more stringent and difficult to meet. For example, a soil moisture sensor might send a single moisture reading – one number – every hour.
SN10-12 7/12/2017 REV 0.5 • • • Excellent Receiving Sensitivity: -125dBm @600bps 2GFSK Excellent Image Rejection: 60 dB Excellent Blocking Performance: 58 dB 2.ELECTRICAL CHARACETRISTICS 2.1 Recommended Operating Range PARAMETER Operating temperature range Operating supply voltage CONDITIONS MIN –40 3.3 TYP 25 MAX 85 3.6 UNIT °C V CONDITIONS MIN TYP MAX UNIT @22dBm, 3.3V 240 260 mA 16.5 17.5 mA MIN -0.3 TYP 2.
SN10-12 7/12/2017 REV 0.5 3. RF Characteristics PARAMETER Center Frequency PARAMETER Antenna port impedance Model SN10-12 CONDITIONS TX 902.2 MIN / / TYP 50 RX 905.2 MAX UNIT MHz UNIT Ω Note SIGFOX RCZ2 Note TX Characteristics Following characteristics are valid for conditions as follows (unless otherwise specified) Tamb = -40 °C to 85 °C, VSS = 0 V, VDD = 2.6 V to 3.6 V, crystal = 55.
SN10-12 7/12/2017 REV 0.5 4.
SN10-12 7/12/2017 REV 0.5 5. Module installation Guide 5.1Mechanical Information 5.2.
SN10-12 7/12/2017 REV 0.5 5.3. Module installation Notice 5.3.1 Do not route traces under module to minimize on interference. (O) (X) 5.3.2 The trace Impedance of the antenna port (Pin 31) is 50 Ω. In order to minimize the return loss, it is recommended to use short traces.
SN10-12 7/12/2017 REV 0.5 5.3.3 Keep enough clearance between the antenna port (Pin 31) and surrounding GND to minimize the power loss. (O) (X) 5.4 . SMT Solder Reflow Notice: Note: Allowable reflow soldering times: 2 times base on recommended reflow profile.
SN10-12 7/12/2017 REV 0.5 5.5 Antenna design declaration: To compliance FCC KDB 996369 D01 v02 cause II. This module can only be used with a host antenna circuit trace layout design in strict compliance with the InnoComm instructions provided. The SN10-12 module use trace antenna in fixture board and compliance 47 CFR FCC Part 15 Subpart C (Section 15.247). For proper integration our modules in end products, we shall provided detailed and comprehensive instructions.
SN10-12 7/12/2017 REV 0.5 Appendix 6.1 SW User Guide information. The SIGFOX software driver supports MCUs. These MCUs are a subset of the MCUs supported by the Kinetis Software Development Kit (KSDK) layer. This SW driver is built on the Analog Middleware Layer (AML), which creates an API abstraction layer for the desired Software Development Kit (SDK). The current implementation includes abstractions for KSDK 2.0 and S32 SDK.
SN10-12 7/12/2017 REV 0.5 Federal Communication Commission Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
SN10-12 7/12/2017 REV 0.5 Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
