BM10_AN R2 BLE Single Mode Module Product Specification Model Name Project code Description Revision Issue Date Approved by Harrison Chen BM10_AN R2 BLE Single Mode Module 1.
iCOM_BM10_AN R2 Module Product Specification 9/26/2017 REV 1.3 Revision History Released Revision Date Comments/Remark Author 1.0 2017/03/07 Initial release Aaron Lai 1.1 2017/03/29 Update reflow profile Aaron Lai 1.2 2017/06/07 Update GPIO pin count to 31 and module photo Aaron Lai 1.3 2017/07/10 Update GPIO pin 31 description and Reference Circuit Aaron Lai 1.4 2017/09/26 Update ME drawing, layout and placement section Aaron Lai ® 2017 InnoComm Mobile Technology Corp.
REV 1.3 iCOM_BM10_AN R2 Module Product Specification 9/26/2017 TABLE OF CONTENT 1. INTRODUCTION ......................................................................................... 4 2. GENERAL INFORMATION ........................................................................ 5 2.1 KEY FEATURES .................................................................................................... 5 2.2 BLOCK DIAGRAM ......................................................................................
iCOM_BM10_AN R2 Module Product Specification 9/26/2017 REV 1.3 1. INTRODUCTION Based on TI’s outstanding CC2640R2 BLE technology, Innocomm’s BM10_AN R2 module is a wireless microcontroller (MCU) targeting Bluetooth® 4.2 and Bluetooth 5 low-energy applications. It is with very low active RF and MCU current and low-power mode current consumption provide excellent battery lifetime and allow for operation on small coin cell batteries and in energy-harvesting applications and embedded PCB antenna.
iCOM_BM10_AN R2 Module Product Specification 9/26/2017 REV 1.3 2. General Information 2.1 Key Features RF • • • • • 2.4-GHz RF Transceiver Compatible With Bluetooth low energy (BLE) 4.
iCOM_BM10_AN R2 Module Product Specification 9/26/2017 REV 1.
iCOM_BM10_AN R2 Module Product Specification 9/26/2017 REV 1.3 2.
iCOM_BM10_AN R2 Module Product Specification 9/26/2017 REV 1.3 3.
iCOM_BM10_AN R2 Module Product Specification 9/26/2017 REV 1.3 3.
iCOM_BM10_AN R2 Module Product Specification 9/26/2017 REV 1.3 4. ELECTRICAL CHARACTERISTICS 4.1 Recommended Operating Range PARAMETER CONDITIONS MIN Operating ambient temperature range, TA Operating supply voltage For operation in battery-powered and 3.3V systems MAX UNIT –40 NOM 85 °C 1.9 3.8 V 4.2 Power Consumption Unless noted, all specifications are at 25 °C and Vbat = 3.0 V. PARAMETER Low Power Mode (LPM4.5) TEST CONDITIONS Shutdown.
iCOM_BM10_AN R2 Module Product Specification 9/26/2017 REV 1.3 5. RF Characteristics 1 Mbps GFSK (Bluetooth low energy) Unless noted, all specifications are at 25 °C, Vbat = 3.0 V and fRF = 2440MHz.
REV 1.3 iCOM_BM10_AN R2 Module Product Specification 9/26/2017 6.
REV 1.3 iCOM_BM10_AN R2 Module Product Specification 9/26/2017 7.
iCOM_BM10_AN R2 Module Product Specification 9/26/2017 REV 1.3 8. Module Placement Layout Guide Placement Note: Please refer to “BM10_AN Module_Placement guideline v1.0.pdf” Layout Note: Do not route any trace under module to avoid interference.
REV 1.3 iCOM_BM10_AN R2 Module Product Specification 9/26/2017 9. SMT Solder Reflow Recommendation Note: Allowable reflow soldering times: 2 times base on recommended reflow profile.
REV 1.3 iCOM_BM10_AN R2 Module Product Specification 9/26/2017 10. Product and Documentation Support 10.1. Development Support TI offers an extensive line of development tools, including tools to evaluate the performance of the processors, generate code, develop algorithm implementations, and fully integrated and debug software and hardware modules.
REV 1.3 iCOM_BM10_AN R2 Module Product Specification 9/26/2017 10.2. Documentation Support To receive notification of documentation updates, navigate to the device product folder on ti.com (CC2640R2F). In the upper right corner, click on Alert me to register and receive a weekly digest of any product information that has changed. For change details, review the revision history included in any revised document.
REV 1.3 iCOM_BM10_AN R2 Module Product Specification 9/26/2017 Federal Communication Commission Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
iCOM_BM10_AN R2 Module Product Specification 9/26/2017 REV 1.3 Radiation Exposure Statement: The product comply with the FCC portable RF exposure limit set forth for an uncontrolled environment and are safe for intended operation as described in this manual. The further RF exposure reduction can be achieved if the product can be kept as far as possible from the user body or set the device to lower output power if such function is available.