InnoComm Mobile Technology Corp. Amazon Modem Module Development Kit User Manual Version 1.
Amazon Modem Module Development Kit User Manual 7/26/2010 Ver1.1 TABLE OF CONTENT 1. INTRODUCTION ...................................................................................... 3 1.1. DEVELOPMENT KIT CONTENT ................................................................. 3 1.2. AMAZON MODEM MODULE AND EXTENSION BOARD PHOTO ......................... 4 1.2.1. Amazon 1: PCI-E Type ............................................................................. 4 1.2.2. Amazon 2: BTB Connector Type ...
Ver1.1 Amazon Modem Module Development Kit User Manual 7/26/2010 InnoComm may make changes to the user guide at any time; the information in this document is subject to change without notice. 1. INTRODUCTION This document describes operation and test setup of Amazon modem module. There are two types with Amazon modem module, one is PCI-E type (Amazon 1) and the other one is BTB connector type (Amazon 2). Extension board is used to connect Amazon modem module to PC side to do function test and debug. 1.
Ver1.1 Amazon Modem Module Development Kit User Manual 7/26/2010 1.2. Amazon modem module and Extension board photo 1.2.1.
Ver1.1 1.2.2.
Ver1.1 Amazon Modem Module Development Kit User Manual 7/26/2010 1.2.3. Extension Board Figure 1-6 Extension Board 2. HW TEST SETUP 2.1. Connect PC USB Port to Extension Board USB Connector Application: Test with Instrument (CMU200, Agilent 8960…) or Real network test Requirement: SW: Driver, CM (Connection manager) installation HW: Test SIM for test with Instrument (CMU200, Agilent8960….etc) x1 Real SIM for test with Real network (Via external antenna) x1 Power supply x 1 Input voltage --- 3.
Ver1.1 Amazon Modem Module Development Kit User Manual 7/26/2010 CMU200 RF cable DC POWER SUPPLY +3.7 +3.
Ver1.1 Amazon Modem Module Development Kit User Manual 7/26/2010 2.2. Connect PC USB Port to Extension Board USIF 1 Port Application: Test with Instrument (CMU200, Agilent 8960…) Requirement: SW: Driver HW: Test SIM card x 1 Power supply x 1 Input voltage --- 3.3 V for Amazon 1 --- 3.7 V for Amazon 2 Instrument (CMU200, Agilent8960….
Amazon Modem Module Development Kit User Manual 7/26/2010 Ver1.1 CMU200 RF cable DC POWER SUPPLY +3.7V +3.
Ver1.1 Amazon Modem Module Development Kit User Manual 7/26/2010 3. SW TEST SETUP 3.1 Driver Installation 3.1.1. HS-USB Driver Installation The HS-USB driver should be installed when using USB Port. Following are the steps for installation. Step 1: Unzip and install the driver. File name: WMC_Comneon2_3.12.1 Driver\ Setup.exe. Then it will create one folder under C:\Program Files\Comneon\Highspeed Modem 0x20\Drivers\.
Ver1.1 Amazon Modem Module Development Kit User Manual 7/26/2010 Figure 3-1 Setup.exe Figure 3-2 Driver folders Step 2: Connect UE device to PC with USB2.0 cable, and power on device Step 3: Install HS_USB Driver to PC. When device powered on and PC detect the device. The driver will install automatically or set direction to C:\Program Files\Comneon\Highspeed Modem 0x20\Drivers\
Ver1.1 Amazon Modem Module Development Kit User Manual 7/26/2010 Figure 3-3: Auto installations 6 virtual ports will be installed. (Comneon Mobile Highspeed Port), and One Modem Port.
Amazon Modem Module Development Kit User Manual 7/26/2010 Ver1.1 Figure 3-4 Virtual Ports 3.1.2. Prolific Driver Installation The Prolific Driver should be installed when using USIF 1 or USIF 5 Port. Following are the steps for installation. Step 1: Unzip and install File name: PL2303_Prolific_DriverInstaller_v10518.exe. Step 2: Plug in USIF1 or USIF 5. PC will detect USB to Serial Ports and install the driver automatically.
Ver1.1 Amazon Modem Module Development Kit User Manual 7/26/2010 Figure 3-6 USB to Serial Ports 3.1.3. Connection Manager Installation Step1: Unzip ProjAmazonSetup.rar and install ProjP330Setup. Figure 3-7 Connection Manager Installation Step 2: Execute Connection Manager on desktop. A Network Connection, NET, will be created and modem should be “Comneon Mobile Highspeed Modem”.
Ver1.1 Amazon Modem Module Development Kit User Manual 7/26/2010 Figure 3-9 Network Connection 3.2 Connection Manager Connection Manager is used to perform network data link and SMS function. Following are basic descriptions of each icon in main menu. Home: Back to Main Menu SMS: - Create new message - List, read/edit Phone Book from SIM, Outlook list. - Inbox, read/reply/ delete from SMS storage.
Amazon Modem Module Development Kit User Manual 7/26/2010 Ver1.1 Home SMS Data link CM Setting Device status Bar Figure 3-10 Main Menu Screen Note: 1. Please use “Exit” to quit CM. Tape the “x” on the window is to minimize CM into Windows application try, and it will not quit the CM. (See Figure 3-11) 2. Do not Open CM twice at same time. Modem com port will be hold when another CM is running. Figure 3-11 correct way to quit CM 3.
Ver1.1 Amazon Modem Module Development Kit User Manual 7/26/2010 Figure 3-13 Prolific_USB -to- Serial Comm Port Step 3: Set up HyperTerminal as Figure 3-14.
Ver1.1 Amazon Modem Module Development Kit User Manual 7/26/2010 Figure 3-15 Send AT command Reference AT commands are as following: 1. Auto-search Network: AT+COPS=0 2. Make a circuit-switch call to instrument: ATD123456; (Do not miss the semicolon.) 3. In case, if SIM is locked by PIN number (e.g., 0000), use AT+CPIN=”0000” to unlock SIM PIN. Before unlock, the SIM PIN Lock will also cause ERROR when issuing AT+COPS=0.
Ver1.1 Amazon Modem Module Development Kit User Manual 7/26/2010 Appendix 1: Detail description of Extension board 1.
Ver1.1 Amazon Modem Module Development Kit User Manual 7/26/2010 2. Connector J312 : USB port J202 : USIF1 Port to USB J203 : USIF5 port to USB J304 : PCI-E Slot J305 : SIM card connector J306 : BTB connector 3.
Ver1.
Appendix 2: Federal Communications Commission (FCC) Statement This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This device has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
