User's Manual

ManualsBrandsINNCOM International ManualsElectronicsHousehold Amenities Control System

Global Leader in Integrated Room Automation Systems

MODEVA Technical Reference Manual

Disclaimer

This document contains information that is the proprietary and confidential property of INNCOM

International Inc. By acceptance hereof, each recipient agrees to use the information contained

herein only for the purpose anticipated by INNCOM, and not to disclose to others, copy or reproduce,

any part hereof without the written consent of INNCOM. The recipient agrees to return this document

to INNCOM immediately upon request.

Content

1 MODEVA Product Overview ........................................................................................ 2

2 MODEVA System Block Diagram ................................................................................. 2

3 Touch User Interface ................................................................................................ 3

4 MODEVA Logic Board ................................................................................................ 4

4.1 RF capability ........................................................................................................... 5

4.2 S5-bus ................................................................................................................... 5

4.3 IR Tx and Rx ........................................................................................................... 5

5 Load Assembly ........................................................................................................ 5

5.1 Categories of Load Assembly Load Switching ................................................................ 5

5.2 Load Assembly Dimming ........................................................................................... 6

5.3 Air-Gap Switch ........................................................................................................ 7

5.4 Overload Protection .................................................................................................. 7

5.5 Load Assembly Parallel Power Supplies ........................................................................ 8

6 MODEVA System Technical Specification ...................................................................... 8

6.1 MODEVA/Load Assembly Current Consumption Characteristics ...................................... 10

7 Load Specifications ................................................................................................. 10

7.1 Single gang installation ........................................................................................... 10

7.2 Multigang Installation ............................................................................................. 11

8 Multigang Installation Derating Chart ........................................................................ 11

8.1 Actuator Ratings .................................................................................................... 11

9 Standard Wiring ..................................................................................................... 12

10 MODEVA User Interface Assembly Ordering Information .............................................. 13

11 MODEVA Load Assembly Ordering Information ........................................................... 15

11.1 Load Assembly Ordering Information ........................................................................ 15

12 Document Information and Revision History ............................................................... 16

Summary of content (16 pages)

PAGE 1
Global Leader in Integrated Room Automation Systems MODEVA Technical Reference Manual Disclaimer This document contains information that is the proprietary and confidential property of INNCOM International Inc. By acceptance hereof, each recipient agrees to use the information contained herein only for the purpose anticipated by INNCOM, and not to disclose to others, copy or reproduce, any part hereof without the written consent of INNCOM.
PAGE 2
MODEVA Reference Manual 1 Page 2 of 16 MODEVA Product Overview The MODEVA™ system, an elegantly designed, easy to use lighting, drapes, and amenities control system, provides an unrivaled guestroom management experience. The MODEVA system allows guest control of multiple loads from many locations.
PAGE 3
MODEVA Reference Manual Page 3 of 16 WBI Mounting Bracket and Actuators GS2 Logic Board Touch Interface Slider Slider GND S5bus 12VDC GND Radio S5bus Circuit WBI Gang 112VDC Slider WBI Gang 2 GND S5bus 12VDC WBI Gang 3 12VDC Power supply Touch PCB Interface 1 LED Array LED Array LED Array Speaker / Piezo Touch PCB Interface 2 Service LED and Switch Service LED and Switch Service LED and Switch Touch PCB Interface 3 IR Rx CPU IR Tx GS2 Interface 1 GS2 Interface 2 GS2 Interface 3 Tou
PAGE 4
MODEVA Reference Manual Page 4 of 16 layout is optimal where six or fewer functions (such as lighting control, amenities such as Do Not Disturb and Make Up Room and general purpose functionality) are required. The Red LED is reserved for Do Not Disturb functionality.  Proximity sensor layout Optionally, a sensor on MODEVA can operate as a proximity sensor by increasing the proximity sensitivity.
PAGE 5
MODEVA Reference Manual Page 5 of 16 all logic communications and interfacing capability, it can be used as a low-voltage remote control interface for load center style applications. 4.1 RF capability MODEVA shares the electrical design of the 0dB 2.4GHz 802.15.4 INNCOM TXR radio module by embedding the radio components in the logic board. This sub-circuit has been specifically tuned for optimal performance for the guestroom environment.
PAGE 6
MODEVA Reference Manual Page 6 of 16 5.1.2 MOSFET Dimmer Power Supply  The MOSFET dimmer is specifically designed to dim capacitive loads such as dimmable fluorescent lamps and electronic ballast. Secondarily, it can also dim resistive loads such as incandescent, halogen, and dimmable LEDs. The MOSFET dimmer is designed to dim 100–120VAC up to 350W.
PAGE 7
MODEVA Reference Manual Page 7 of 16 5.2.3 Variable baseline frequency 5.2.4 Impulse noise Caused by backup generators and small power grids. Caused by switch arcing (loads switching on and off). 5.2.5 RMS voltage changes 5.2.6 Notch and low frequency noise Caused by heavy load switching. Caused by elevators and large industrial loads TRIAC and MOSFET dimmers can withstand certain levels of any one kind of the noises listed above.
PAGE 8
MODEVA Reference Manual 5.5 Page 8 of 16 Load Assembly Parallel Power Supplies 550mA R Load 12VDC 375mA 200mA WBI Actuator 2 WBI Actuator 3 GND Lighting Load WBI Actuator 1 WBI MOSFET Dimmer WBI MOSFET Dimmer WBI MOSFET Dimmer Hot 120/240VAC 50/60Hz Neutral Figure 5 Parallel Power Supplies The WBI actuators operate in parallel to supply a higher load capacity than that achievable by a single actuator.
PAGE 9
MODEVA Reference Manual Glass Touch Surface Area Page 9 of 16 Length Width Height American Single Gang 115mm 70mm 2.0mm American Double Gang 115mm 120mm 2.0mm American Triple gang 115mm 170mm 2.0mm Electrical Characteristics Parameter User Interface Capacitive touch sensor / slider Maximum # of inputs 1-6 sensor inputs, or 1 slider per gang Alternate User Interface Keypad—traditional mechanical switches Communications 1. Wired S5-bus 2. 2.4Ghz RF 3.
PAGE 10
MODEVA Reference Manual 6.1 Page 10 of 16 MODEVA/Load Assembly Current Consumption Characteristics Device Peak Current Consumption Logic Board (basic) 50mA Logic Board w/ 1mW Radio 60mA Logic board with IR transceiver 70mA Capacitive Touch PCBA (02-7060) 10mA(n x 3.
PAGE 11
MODEVA Reference Manual Page 11 of 16 Actuator Ratings Voltage MOSFET Dimmer 7.2 Frequency Power / Amperes Load Type 120 Vac 60 Hz 2.9 A Resistive 120 Vac 60 Hz 2.9 A General Purpose 120 Vac 60 Hz 350 W Tungsten / ELV 120 Vac 60 Hz 250 VA Electronic Ballast Multigang Installation The MODEVA and Load Assembly comes in single, double and triple gang configurations; the double and triple gang assemblies may be any combination of relay, switches, MOSFET Dimmer or TRIAC Dimmer.
PAGE 12
MODEVA Reference Manual Page 12 of 16 Actuator 9 120 Vac 60 Hz 250 W Ratings Tungsten 120 Vac 60 Hz 250 VA Electronic Ballast Standard Wiring Figure 6 Single Gang Wiring Diagram In Figure 6, the MODEVA and Load Assembly is configured for switching or dimming the level of AC power delivered to a load, such as a Tungsten lighting load.
PAGE 13
MODEVA Reference Manual Page 13 of 16 Figure 8 Single Gang Powered Remote Control In the configuration shown in Figure 8, the MODEVA is used as a three-way switch to transmit S5bus or RF signals to auxiliary INNCOM devices to manage in-room communications irrespective of the location of the system devices. In this respect, the MODEVA provides remote control of auxiliary INNCOM devices.
PAGE 14
MODEVA Reference Manual Page 14 of 16 03-7060 GHS1 R0 WH Assembly Part Number 03-7060 – Single Gang Assembly 03-7061 – Double Gang Assembly 03-7062 – Triple Gang Assembly Switch Model Defined by project Radio R0 = No Radio R1 = Layer-1 Radio (02-9994.L1) R2 = Layer-2 Radio (02-9894.
PAGE 15
MODEVA Reference Manual Page 15 of 16 12 MODEVA Load Assembly Ordering Information 12.1 Load Assembly Ordering Information The Load Assembly system is available in several operating ranges but is based on the same fundamental hardware platform. The ordering part numbers (OPN) are formed by a combination of the elements, as shown in Figure 7 below.
PAGE 16
MODEVA Reference Manual Page 16 of 16 13 Document Information and Revision History Author File Ryan Gardner \\Niantic\departments\R&D\Working Documents\Reference Manuals\MODEVA\Drafts Date Changes 13-Oct-2009 First Draft 16-Oct-2009 Edited for content and composition 02-Mar-2010 Product information added and edited 09-Apr-2010 Updated Derating chart for UL 20-Apr-2010 Updated order guide to include radio option for logic components 18-Jun-2010 Update to reflect name changes; new ratings tabl