WD-1 NETWORK AV ADAPTER ADAPTATEUR AV RÉSEAU ADAPTADOR AV CON CONEXIÓN DE RED OPERATING INSTRUCTIONS GUIDE D’UTILISATION INSTRUCCIONES DE FUNCIONAMIENTO
Safety Information READ THIS BEFORE OPERATING YOUR UNIT CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE FRONT OR BACK COVER. NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. This symbol indicates the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock.
Reorient or relocate the receiving antenna. Increase the separation between the equipment and the receiver. Connect the equipment to an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. 7 8 9 This device complies with part 15 of the FCC Rules.
Table of Contents 2 Safety Information 5 Getting Started 5 What's Included 6 Installing the Remote Control Battery 6 Operating the range of the Remote Control 7 Parts Description 9 Making Connections 9 Connecting HDMI Components 10 Connecting Digital Audio Components 10 Connecting to a Network 11 Connecting Power 12 Operating Your Device 12 Turning on Your Unit 12 Setting the Network Standby Control 12 Setting the Network Setup 14 Listening to Internet Radio 15 Listening to Mu
Getting Started English What's Included Main unit Remote control (1 ea) Battery “AAA” size, 1.5V (2 ea) WD-1 NETWORK AV ADAPTER OPERATING INSTRUCTIONS Power adapter (1 ea) User manual (1 ea) Note •• The items supplied with your unit are subject to change without prior notice.
WD-1 NETWORK AV ADAPTER Installing the Remote Control Battery 1 2 Remove the battery cover. Operating the range of the Remote Control Use the remote control within a range of about 7 meters (23 feet) and angles of up to 30 degrees aiming at the remote control sensor. Insert two AAA size batteries with the polarity matched properly. 7m 30 Caution •• Always use alkaline batteries, and do not use the rechargeable batteries (Ni-Cd type).
Getting Started English Parts Description Front and Rear Panel 1 7 6 1 2 3 4 2 5 3 4 Status LED Power Connector OPTICAL OUT Connector 5 6 7 HDMI Connector USB Connector (For Upgrade only) IR Sensor LAN/ETHERNET Connector 7
WD-1 NETWORK AV ADAPTER Remote Control 1 1 11 2 3 3 10 4 4 5 6 2 9 8 7 5 6 POWER ON Turn on the main unit. MODE Adjust the screen resolution. (Original/Full) DISPLAY •• When playing audio or video files, turns on or off the progress bar. •• When viewing photos, turns on or off the slideshow transition time display. / / / / ENTER •• Navigate through the menus. •• Confirm a setting option or menu. TOP MENU Move to the top menu for each media or service. Fast-reverse the current file.
Making Connections With HDMI, you can easily enjoy high quality sounds and images. The main unit plays audio from HDMI compatible products while also passing on the video signal to a HDMI‑connected TV. About HDMI HDMI (High Definition Multimedia Interface) supports both audio and video on a single digital connection for use with DVD players, DTV, set-top boxes, and other AV devices.
WD-1 NETWORK AV ADAPTER Connecting Digital Audio Components You can connect components equipped with an optical input jack. Then, the main unit transmits the digital audio signal to the connected external device. Connecting to a Network If you have an internet connection, you can connect the main unit to the internet as well as using a wireless or a wired LAN connection. The following illustration is a configuration example of a home network with the main unit and a server.
Note •• After making a broadband internet connection, you should set the communication settings. For details, see “Setting the Network Setup” on page 12. •• When using a broadband internet connection, a contract with an internet service provider is required. For more information, contact local internet service provider. •• Since the connected equipment and connection method may differ depending on your internet environment, refer to the operating instructions of the equipment.
Operating Your Device Turning on Your Unit 1 Turn on the main unit by pressing POWER ON. 2 Turn off the standby mode by pressing STANDBY. Setting the Network Setup To listen to Internet radio stations or music files stored on your computer via a wired or wireless network, you should configure network settings first. 1 Setting the Network Standby Control 1 2 Press SETUP. Press or to navigate up or down the menu. Press and hold SETUP for more than 3 seconds.
Network Settings Overview Main Menu Sub Menu Go to Page Setting the Wired Network Connection Before you setup the connection, check that the LAN cable is connected to the LAN/ ETHERNET connector properly and securely. For details, see “Connecting to a Network” on page 10. Soft AP hotspot 13 Wi-Fi direct 13 Ethernet 13 Ethernet Ethernet Configuration 13 You can enable and set the Ethernet connection automatically on the main unit.
WD-1 NETWORK AV ADAPTER Listening to Internet Radio Setting Other Network Options Menu item Description AP Name Views and changes the name of the unit displayed on the network. Resolution Sets the resolution of the video output. Display size Adjusts the screen display size manually. Factory Setting Resets all the settings to the factory default. You can listen to Internet radio broadcasts provided by vTuner. You can control the internet radio with the menu displayed on the TV screen.
2 Listening to Music from the Media Server Select the desired category by pressing or , and then press ENTER on the remote control. You can play music files stored on a computer (media server) connected to this unit via a wired or wireless network. You can share the music files easily by using Windows Media Player 11 or later versions. Configuring the Windows Media Player On Windows Media Player 11 version 1 2 3 4 Note •• To use this function, the unit should be connected to the internet.
WD-1 NETWORK AV ADAPTER Using the Sherwood Remote Application Listening to Music from the Media Server 1 2 Start your computer. Select Media Server on the screen, and then press ENTER on the remote control. Preparing for the Application Setting the Network on the Main Unit 1 3 Select the desired category by pressing , , and then press ENTER on the remote control. 2 Press SETUP on the remote control. Tap Hotspot & Wi-Fi Direct > Soft Wi-Fi hotspot or Wi-Fi direct.
Operating Your Device 1 2 3 4 5 Visit Play Store on your Android Smartphone. Or visit App Store on your iPhone. Search for Sherwood Remote. Download and install the application on your phone. Using the Application The Sherwood Remote application helps you to control the main unit remotely by allowing you to use Wiink. 1 2 Open the Sherwood Remote application. When the product search window is activated, select and tap WD-1. Then, you can use your smartphone as a remote control for the main unit.
WD-1 NETWORK AV ADAPTER Using Direct AV •• iOS On Direct AV, you can listen to songs, watch videos, and view photos stored on your Android phone or iPhone. 1 Tap Direct AV. •• Android 2 •• : Adjust the settings. •• : Turn on or off the main unit. (To activate the function, you should turn on the Network Standby Control. Then, the power consumption may increase. Refer to “Setting the Network Standby Control” on page 12 for details.) Tap Audio to listen to the songs stored on your phone.
Operating Your Device Watching Videos on Your Smartphone You can select a song on the song list and play it over the main unit. You can select a video on the video file list and enjoy it on the main unit. 1 1 7 8 2 3 7 4 6 5 6 2 3 5 4 No. No. Description 1 Move to the previous menu •• This menu is not displayed on Android smartphone.
WD-1 NETWORK AV ADAPTER Viewing Photos on Your Smartphone Using Internet Radio and Media Server You can view photos as a slideshow and set the slideshow transition time at Off, 5s, 10s, 20s, 30s. You can use your smartphone as a remote controller for Internet Radio and Media Server. 1 Tap Internet Radio or Media Server. 1 2 No. 3 Description 1 Move to the previous menu •• This menu is not displayed on the Android smartphone.
Updating the Firmware Overview of the Main Screen 1 6 2 5 4 3 No. 1 New firmware that provides additional features or product improvements will be released as needed. Updates can be downloaded from our website: www.sherwoodamerica.com. After downloading the firmware to a USB device, you can update the main unit by connecting the USB device with a USB OTG cable(faster than USB 2.0) and doing the following procedures. For details, refer to the information supplied with updates.
WD-1 NETWORK AV ADAPTER 1 Connect the USB connector of the main unit to the device which stores the firmware. 2 Press the buttons in the following order. MODE ENTER Note •• When the main unit does not turn on automatically after updating, you should turn on the unit manually. •• Make sure not to turn off the main unit, disconnect the USB cable or perform any operation on the main unit while the updating operation is in progress.
If you experience any of the following difficulties while using the main unit, use this troubleshooting guide to help remedy the problem before requesting servicing. Should any problem persist, consult your nearest authorized dealer or authorized independent company. If the unit does not operate normally due to external influence such as static electricity, disconnect the power plug from the outlet and insert again to return to normal operating conditions.
Additional Information Specifications Input/Output HDMI Output 1 Audio Output Optical x1 (Digital) Supported Codecs Audio Codec Type MP3 MP3 WMA WMA, WMV WAVE AC3 Codec Video H.264 (MPEG4 AVC) Codec Sampling rate (kHz) Bitrate (max in Channel Kbps) CBR/VBR up to 48 kHz from 8 kbps to mono, stereo 320 kbps up to up to 48 kHz mono, stereo 192 kbps at 8, 16 and mono, stereo 44.1 kHz *.mp3 *.wma, *.wmv LPCM, m-law, a-law Dolby Digital 5.
Trademarks and Licenses English HDMI HDMI, the HDMI Logo, and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries. Dolby Digital Dolby and the double-D symbol are trademarks of Dolby Laboratories. Wi-Fi The Wi-Fi CERTIFIED Logo is a certification mark of the Wi-Fi Alliance.
Informations de sécurité À LIRE AVANT D'UTILISER L'APPAREIL ATTENTION RISQUES D'ELECTROCUTION NE PAS OUVRIR ATTENTION AFIN DE REDUIRE LES RISQUES DE CHOC ELECTRIQUE, N'ENLEVEZ PAS LE PANNEAU ARRIERE. AUCUNE PIÈCE À L'INTÉRIEUR NE PEUT ÊTRE RÉPARÉE PAR L'UTILISATEUR. EN CAS DE PROBLÈME, S'ADRESSER À UN PERSONNEL TECHNIQUE QUALIFIÉ.
Brancher l'équipement dans une prise de courant d'un circuit différent de celui sur lequel le récepteur est branché. 7 8 Consulter le revendeur ou un technicien radio/ télévision qualifié pour toute assistance. Cet appareil est conforme à la section 15 de la réglementation de la FCC.
Table des matières 26 Informations de sécurité 29 Mise en route 29 Contenu de l'emballage 30 Installation des piles de la télécommande 30 Portée de la télécommande 31 Description des composants 33 Etablissement des connexions 33 Connexion de sources HDMI 34 Raccordement d’appareils audio numérique 34 Connexion au réseau 35 Branchement au courant 36 Utilisation de l'appareil 36 Allumer l'appareil 36 Réglage de l’état de veille réseau 36 Configuration réseau 38 Ecouter la radio Interne
Mise en route Français Contenu de l'emballage Unité principal Télécommande (1 ea) Piles « AAA » 1,5V (2 ea) WD-1 NETWORK AV ADAPTER OPERATING INSTRUCTIONS Adaptateur secteur (1 ea) Guide d'utilisation (1 ea) Remarque •• Les articles livrés avec votre appareil sont susceptibles de modification sans préavis.
WD-1 ADAPTATEUR AV RÉSEAU Installation des piles de la télécommande 1 Enlevez le couvercle du compartiment des piles. 2 Insérez deux piles AAA en respectant les polarités. Attention •• Utilisez toujours des piles alcalines. N'utilisez jamais de piles rechargeables (de type Ni-Cd). •• Lorsque les piles sont usées, les remplacer immédiatement par de nouvelles piles. •• Si les piles sont enlevées ou usées depuis longtemps, le contenu de la mémoire sera effacé.
Mise en route Français Description des composants Panneau avant et arrière 1 7 6 1 2 3 4 2 5 3 4 Voyant d'état Prise d'alimentation Prise de sortie optique Prise LAN/ETHERNET 5 6 7 Prise HDMI Prise USB (pour mise à jour du logiciel uniquement) Capteur infrarouge 31
WD-1 ADAPTATEUR AV RÉSEAU Télécommande 1 11 2 3 10 4 5 6 1 MISE EN MARCHE Allume l'unité principale. 2 MODE Réglage de la résolution de l’écran (Original/Total) 3 AFFICHAGE •• Active/désactive la barre de progression lors de lecture de fichiers audio ou vidéo. •• Active/désactive l'affichage de l’intervalle de transition diaporama lors de l'affichage photos. 4 / / / / ENTER •• Permet de naviguer dans les menus. •• Permet de confirmer une option de réglage ou menu.
Etablissement des connexions HDMI vous permet de bénéficier de sons et d'images de haute qualité. L'unité principale peut lire l'audio à partir d'appareils compatibles HDMI tout en passant le signal vidéo sur un téléviseur HDMI connecté.
WD-1 ADAPTATEUR AV RÉSEAU Raccordement d’appareils audio numérique Vous pouvez raccorder des appareils équipés d'une prise de sortie optique. L'unité principale transmet le signal audio numérique aux appareils externes raccordés. Connexion au réseau Si vous disposez d'une connexion Internet, vous pouvez connecter l'unité principale à Internet, sans fil ou de manière câblée. L'illustration suivante donne un exemple de configuration d'un réseau local avec l'unité principale et un serveur.
Remarque •• Une fois une connexion Internet large bande est établie, vous devez régler les paramètres de communication. Pour plus de détails, voir « Configuration réseau » à la page 36. •• Lorsque vous utilisez une connexion Internet large bande, cela suppose que vous ayez souscrit à un abonnement auprès d'un fournisseur de services Internet. Pour plus d'informations, contactez le fournisseur de services Internet local.