1. Installation F low C hart...................................... ................................................................ 8 2. Pac kage C hec k ................................................ ............................................................... 9 2.1 LINK ANT .................................................... .......................................................... 10 2.2 C OVERAGE UNIT(C U) ........................................... ..........................Appendix B. S ystem S pec ific ations ............................... ....................................................... 37 Appendix C . S ystem Bloc k........................................ .......................................................... 38 Appendix D. Troubleshooting for S OHO ............................ . 오류! 책갈피가 정의되어 있지 않습니다.
Fig. 1 Installation Flow Chart .................................................................................................................................... 8 Fig. 2 List of all the Components in the System ................................... 오류! 책갈피가 정의되어 있지 않습니다. Fig. 3 LINK ANT....................................................................................................................................................... 10 Fig. 4 COVERAGE UNIT(CU)..................................
Table 1 Band Setting ................................................................................................................................................. 15 Table 2 Cellular Frequency .................................................................... 오류! 책갈피가 정의되어 있지 않습니다. Table 3 PCS Frequency............................................................................................................................................. 35 Table 4 RF Specifications.......................
1. Installation F low C hart This doc ument will provide details on how to suc c essfully install the J uni J R- 10 S OHO Repeater system. The flow c hart below shows the main steps involved in setting up the equipment. 1. S tart 2. Package C heck 3. Loc ating 4. Band S etting 5. Link Ant 6. Power / Optimization 7. C U 8. S tatus C hec k 9. End F ig.
2. Pac kage C hec k The first step when installing the repeater is to c hec k if all c omponents are present and that the parts do not c ontain any visible faults. The figure below illustrates the items inc luded in the J R- 10 S OHO Repeater Kit. F ig.
2.1 LINK ANT Î The role of the Antenna Unit is to c ommunic ate with the BTS . It is usually loc ated outside the building where servic e is to be improved. The Antenna Unit c an be mounted onto a wall or a pole, depending on the spec ific installation needs. F ig. 3 LINK ANT 2.2 C OVERAGE UNIT (C U) Î The role of the C overage Unit is to c ommunic ate with the mobiles within the building where needs improved c overage. It is intended for wall mounting. F ig.
3. Preparing for Antenna Unit and C overage Unit Installation Determining the installation loc ation of the unit is viewed as one of the most important c hoic es, as the plac e of c hoic e of the unit will heavily impac t the overall performanc e of the repeater. The first selec tion that needs to be made by the user is to determine if the units will be mounted to a wall or a pole. Onc e this dec ision has been c onfirmed, the c hoic e of loc ation c an be arranged.
4. F requenc y Band S etting Onc e the loc ation and positioning of the Antenna Unit and C overage Unit are finalized, the authorized installer should proc eed with installing the Antenna Unit and C overage Unit. But first, the installer should set the appropriate operating frequenc y band(s) for the repeater, based on Verizon Wireless lic enses. The figure and table below show the DIP S witc h settings. Usually both PC S and C ellular bands have to be set up. Î DIP S witc h F unc tions F ig.
BW UP LINK DOWN LINK 1850 ~ 1855 1930 ~ 1935 DIP S WITC H REMARK White ON 1 2 3 4 5 6 7 8 9 10 11 12 c olor is switc h.
ON 1860 ~ 1870 1940 ~ 1950 1 2 3 4 5 6 7 8 9 10 11 12 7 8 9 10 11 12 ON 1865 ~ 1875 1945 ~ 1955 1 2 3 4 5 6 ON 1870 ~ 1880 1950 ~ 1960 1 2 3 4 5 6 7 8 9 10 11 12 3 4 5 6 7 8 9 10 11 12 3 4 5 6 7 8 9 10 11 12 3 4 5 6 7 8 9 10 11 12 3 4 5 6 7 8 9 10 11 12 3 4 5 6 7 8 9 10 11 12 3 4 5 6 ON 1875 ~ 1885 1955 ~ 1965 1 2 ON 1880 ~ 1890 1960 ~ 1970 1 2 ON 1885 ~ 1895 1965 ~ 1975 1 2 ON 1890 ~ 1900 1970 ~ 1980 1 2 ON 1895 ~ 1905 1975 ~ 1985 1 2 ON 1900 ~ 1910 1980 ~ 1990 1 2
ON 1880 ~ 1895 1960 ~ 1975 1 2 3 4 5 6 7 8 9 10 11 12 3 4 5 6 7 8 9 10 11 12 3 4 5 6 7 8 9 10 11 12 3 4 5 6 7 8 9 10 11 12 ON 1885 ~ 1900 1965 ~ 1980 1 2 ON 1890 ~ 1905 1970 ~ 1985 1 2 ON 1895 ~ 1910 1975 ~ 1990 1 2 Table 1 Band S etting 15
5. LINK ANT. Installation 5.1 BRAC KET/MTG Image 5.1.1. LINK ANTENNA 에 BRAC KET – ANT C onnec tion Image 1) The length unit is [ mm] . F ig. 6 LINK ANT MTG BRAC KET_ANT C onnec tion Image 5.1.2. BRAC KET/MTG C onnec tion Image to Installation Plac e(WALL or POLE ) ( Lumber Wall ) ( C onc rete Wall ) ( Pole ) F ig.
5.2 LINK ANT MTG Brac ket C onnec tion 1) APPLY 1/4” NUT, S PRING WAS HER, PLATE WAS HER to LINK ANT. (Do not C onnec t C ompletely) 2) APPLY BRAC KET- ANT TO LINK ANTENNA. 3) APPLY NUT C OMPLETELY US ING PROVIDED TOOL. [ 1/4” NUT, 1/4” S PRING WAS HER, 1/4” PLATE WAS HER 4ea, BRAC KER- ANT 1ea] F ig.
5.3 BRAC KET C onnec tion depending on Installation Plac e 5.3.1. POLE MOUNTING 1) S ec ure DU to the pole using U- BOLT. 2) Insert U- BOLT to between BRAC KET- POLE and BRAC KET- DU 3) Apply the pole to the BRAC KET- DU: use the nuts and u- bolts provided to fixate the brac ket into the Pole. [ BRAC KET- ANT 1ea, BRAC KET- POLE 2ea, U- Bolt 2ea, 1/4” NUT, 1/4” S PRING WAS HER, 1/4” PLATE WAS HER eac h 4ea] F ig. 9 POLE MOUNTING MTG BRAC KET_ANT C onnec tion S equenc e 5.3.2.
5.3.3. C ONC RETE WALL MOUNTING 1) Drill on the wall as the BRAC KET- ANT distanc e.(forφ 10mm Hole depth to be 30 to 40 mm. 2) INS ERT S ET- ANC HOR TO DRILLED HOLE. 3) S ec ure BRAC KET- DU to the Wall and fix the nut. [ S ET- ANC HOT 4ea, BRAC KER- ANT 1ea] F ig.
5.4 LINK ANTENNA C onnec tion (same as 5.2) with BRAC KET (same as 5.3) 1) APPLY LINK ANTENNA to the BRAC KET. 2) Apply the NUT to the upside of BRAC KET like below sequenc e. – Do not apply the NUT c ompletely. 3) S et the rec eiving direc tion of the ANTENNA and apply the NUT c ompletely using the provided tool. [ 1/4” NUT, 1/4” S PRING WAS HER, 1/4” PLATE WAS HER 각 4ea] F ig.
5.5 Installation C ompletion. F ig. 13 LUMBER WALL MOUNTING F ig. 14 C ONC RETE WALL MOUNTING F ig.
6. Power C onnec tion and Optimization S ETTING Onc e the Antenna Unit, RF C able and C overage Unit have been suc c essfully installed, the authorized installer should c onnec t the Power Adaptor and AC power to the equipment and make the c orrec t system settings. The C overage Unit LED indic ator is needed when proc eeding with the optimization setting. 1) C onnec t the RF C able between the Antenna Unit and the C overage Unit as shown in the diagram below.
F ig. 17 Verifying rec eption status Outdoor LINK ANT. on a Roof (Pole mount) Outdoor LINK ANT. (Wall mount) Onc e the Antenna Unit is mounted onto the pole, it is c apable of being rotated 20° in either direc tion. The Antenna Unit c an also be mounted anywhere around the pole. C an be rotated 20° in either direc tion F ig.
3) The type of mounting method used will determine how muc h flexibility it has in revolving from its position. 7. RF UNIT(C U) Installation (Wall & C eil Mount) 1) Using the C overage Unit Mounting Brac ket as a drilling template, drill C overage Unit Mounting Brac ket holes into the wall for the appropriate mounting hardware, depending on the type of wall (c onc rete, drywall, plaster, wood, veneer).
7.1.2. BRAC KET- C U MTG C onnec tion to Wall Image F ig. 20 MTG BRAC KET – C U C onnec tion Image 7.2 INS TALL BRAC KET C onnec tion to C U 1) Apply BRAC KET – S ET to C U c ompletely using NUT, S PRING and PLATE WAS HER. 2) Apply S C REW to BRAC KET – S ET suitably.
F ig. 21 MTG Brac ket – C U S ET C onnec tion S equenc e 7.BRAC KET C onnec tion depending on Installation Plac e 7.3.1. LUMBER WALL MOUNTING 1) S ec ure BRAC KET- C U MTG to the wooden wall. Using c ross driver, c onnec t c ompletely S C REW to wooden wall through BRAC KET- MTG. [ C U BRAC KET- MTG 1ea, S C REW 4ea] F ig.
7.3.2. GYPS UM BOARD WALL MOUNTING 1) S ec ure DRYWALL anc hor to the GYPS UM BOARD WALL using c ross driver c ompletely. 2) S ec ure DRYWALL anc hor sc rew to BRAC KET – C U MTG using c ross driver c ompletely. [ BRAC KET- C U MTG 1ea, Drywall Anc hor 4ea, S c rew 4ea] F ig. 23 GYPS UM BOARD WALL MTG Brac ket MOUNTING 7.3.3. C ONC RETE WALL MOUNTING 1) S ec ure PLAS TIC ANC HOR TO WALL. (Removal is impossible after c onnec tion.
7.4 C onnec tion C U(same as 7.2) with C U BRAC KET- MTG(same as 7.3) 1) APPLY C U to BRAC KET- C U MTG. 2) After sec uring C U to Wall, c onnec t the S C REW (M4X12L S EMS ) to the BRAC KET. [ S C REW(M4X12L S EMS ) 2ea] F ig.
7.5 Installation C ompletion. F ig. 26 C U S ET Installation C ompletion Image 5) Onc e the positioning of the C overage Unit has been finalized, use the DIP S witc h to ac tivate the Uplink path. 1 2 3 4 5 6 7 8 9 10 11 1 2 3 4 5 6 7 8 9 10 11 F ig.
8. S tatus C hec k 8.1 C overage Unit Alarm LE Ds If any Alarm LED is ac tivated: A red LED will indic ate that the equipment is not func tioning properly. Eac h of the LEDs represents the status of a spec ific sec tion of the system as shown below F ig. 28 C overage Unit LED ▶ MANUAL OF F – If the authorized installer dec ides to turn off the system, this LED will turn red.
Appendix A. Produc t Introduc tion A.1 1 Overview The J uni J R- 10 S OHO Repeater system is an RF repeater whic h provides c overage for indoor loc ations within a BTS c overage area. The repeater is intended to serve indoor loc ations where there is very little or no RF c overage. The system supports both US C ellular and PC S bands. Verizon Wireless- authorized installation personnel are able selec t to bands via the internal band selec tion func tion.
The diagram below shows the basic system c onfiguration. It c an be seen that the RF c able c onnec ts the LINK ANT to the C U. The power c able is also c onnec ted to the C U. F ig.
A.2 Requirements and limitations when installing the Repeater system ▶ Operator : Verizon Wireless ▶ Frequenc y Band in Use : C ELLULAR or PC S Î C ELLULAR F requenc y Range Î C ellular Band: (B1 and B2) or (A1 and A2) depending on Verizon Wireless’ C ellular Band lic ense for the area where the repeater is to be installed.
Appendix B. S ystem S pec ific ations F requenc y Bands PC S Uplink : 1850 – 1910MHz Downlink : 1930 – 1990MHz C ELL Uplink : 824 – 849MHz S ub- Bands Downlink : 869- 894 MHz C ell : A+A’, B+B’ PC S : 5 , 10 , 15 MHz F ormats S upported IS - 95 / C DMA / 1X E VDO Typic al C overage Area 2,500 sq.
Appendix C .
Appendix D. Troubleshooting for J R- 10 S OHO Repeater Alarm LED C olor Possible Reason Ac tion Required Ac tion MANUAL Green When servic e provider C hec k Alarm OF F - > Red forc es the S ystem OF F - > C all J uni Tec hnic al S upport S hutdown by RF - Exc essive Output Power: Green Exc essive Output Automatic ally Rec overed.