尺寸：130x160mm 类型：骑马钉
Smart Fan Controller RRANT Y wA Inline Duct Fan VOID IF SEAL BROKEN IVC-001W
CONTENTS 01 Overview 02 Features & Specifications 03 Product Contents 04 INKBIRD App 05 Smart Controller Instructions 06 Automatic Control Mode Instructions 07 Manual Control Mode Instructions 08 Timer Control Mode Instructions 09 Shutdown Mode 10 Lock Mode 11 ECO Mode 12 Parameter Factory Setting 13 Inline Duct Fan Installation Instructions 14 FCC Requirement 01 01 02 03 03 04 09 10 13 13 13 13 14 22
01 Overview 02 Features & Specifications Shutdown +8 RH(%RH) maximal tolerance typical tolerance +6 +4 +2 +0 0 10 20 30 40 50 60 70 80 90 100 Relative Humidity(%RH) 1
T(℃) +1.5 maximal tolerance typical tolerance +1.0 +0.5 +0.
04 INKBIRD App 05 Smart Controller Instructions P1 3 P2 WORK1 WORK2
06 Automatic Control Mode Instructions The fan will run at the set fan speed according to the relationship between the current temperature and humidity and the trigger target temperature and humidity. How to set the fan to run at a fan speed of 10 to keep the temperature at 81.0℉ to 82.0℉ and the humidity at 70.0%RH to 80.
Step2: Press and hold the button for 2 seconds to enter the setting mode, or press or button to enter the quick setting mode, in which “SETTING” is displayed. Press the button until the fan speed parameter flashes, then press the or button to adjust the fan speed to 10. Step1: Press the button to select automatic control mode, in which the symbol is displayed. SETTING Step3: Press the button to select the high-temperature trigger value. “HIGH TEMP.” is displayed and the corresponding parameter flashes.
Step5: Press the button to select the high-humidity trigger value. “HIGH HUMD.” is displayed and the corresponding parameter flashes. Press the or button to adjust the high-humidity trigger value to 80.0%RH. Step6: Press the button to select the low-humidity trigger value. “LOW HUMD.” is displayed and the corresponding parameter flashes. Press the or button to adjust the low-humidity trigger value to 70.0%RH. SETTING SETTING HIGH TEMP.ALARM DIFF.TEMP.VALUE LOW TEMP.ALARM TEMP.CALIBRATION HIGH HUMID.
Fan status ON OFF 70.0%RH Humidity trigger value 80.0%RH How to disable the high-temperature trigger function? Step2: Press and hold the button for 2 seconds to enter the setting mode. Press the button to select the high-temperature trigger value. “HIGH TEMP.” is displayed and the corresponding parameter flashes. Press both and buttons simultaneously and hold for 2 seconds to display OFF and turn off the high-temperature trigger function.
Step3: Press and hold the button for 2 seconds or no operation for 60 seconds to quit the setting state and save the set parameters. Low-temperature trigger, high-humidity trigger, and low-humidity trigger functions can be turned off by referring to the above steps. Note that at least one trigger function should remain on. How to set temperature unit/temperature alarm value/humidity alarm value/calibration value? Step1: Press and hold the “SETTING” is displayed.
Step3: Press and hold the button for 2 seconds or no operation for 60 seconds to quit the setting state and save the set parameters. Note: When setting the high-temperature alarm value/low-temperature alarm value/high-humidity alarm value/low-humidity alarm value, press and hold the and buttons simultaneously for 2 seconds to display OFF and disable the corresponding alarm function. SETTING HIGH TEMP.ALARM DIFF.TEMP.VALUE LOW TEMP.ALARM TEMP.CALIBRATION HIGH HUMID.ALARMDIFF.HUMID.VALUE LOW HUMID.
Step3: Press the button to select the fan run time. Press the or button to adjust the time display . Step4: Step4: Press and hold button for 2 seconds or no operation for 60 seconds (or 5 seconds in the quick setting mode) to quit the setting state and save the set parameters. Following the above steps, the fun will run continuously at a fan speed of 8 until manually turned off.
Step1: Press the button to select the timer mode, in which the symbol is displayed. Step2: Press and hold the button for 2 seconds, or press the or button to enter the setting mode. SUN. MON. TUES. WED. THURS. FRI. SAT. SUN. MON. TUES. WED. THURS. FRI. SAT. START TIME SETTING AM Step3: Press the or button to select the day to be set. Here we choose Monday as an example. Step4: Press the button to enter the setting of active time segments, in which “START TIME ” is displayed.
Step5: Press the button to set the run time of segment 1, and “TIME SETTING” is displayed. Press the or button to adjust the run time to 02:00. Step6: Press the button to set the fan speed of segment 1, and the fan symbol is displayed. Press the or button to adjust the fan speed to 8. SUN. MON. TUES. WED. THURS. FRI. SAT. SUN. MON. TUES. WED. THURS. FRI. SAT.
09 Shutdown Mode All control functions are disabled. Press the turned off. button to select the shutdown mode, in which all functional controls are 10 Lock Mode In the non-setting state, press and hold the and button for 2 seconds simultaneously to turn on/off the lock function. When the lock function is on, the symbol is displayed. 11 ECO Mode In the power-off state, press and hold the button for 2 seconds to enter the setting of backlight brightness.
13 Duct Fan Instructions Bottom cover Frame Screw Hoops Duct-A Duct-B Impelle Duct ALRFLOW 150 Power cover Butt plate DC Connect Wire (2.4m length 26AWG) AC Power Cord (1.
Installation Instructions Step3: Use the mounting holes of the flange bracket to mark the position to be mounted. (Pay attention to the direction of intake/exhaust during installation, referring to the instructions for intake/ exhaust.) Step4: Drill four holes at the marked locations. Make sure the installation area is well constructed and free of obstructions. 150 Step2: Remove the power supply chassis from the rack. ALRFLOW Step1: Unscrew the annular threaded nail of the duct fan.
Step7: Put the wind circle back on the intake flange and reposition the flange on the appropriate metal clips. Step8: Move the power supply chassis back onto the flange bracket, making sure that the bulging part of the power supply chassis is installed in the direction of the flange bracket arrow. Use a Phillips screwdriver and pliers to tighten the metal clips and secure the power supply chassis.
Step9: Put the metal ring back onto the flange and tighten the screws to fix the fan. Step10: When installing the duct, use the included duct clamps to secure it to either end of the duct fan, making sure it is tightly sealed. Use a flat-head screwdriver to tighten the duct clamps. Step11 A: Hang Up—— If using a rope bridge (not included) for installation, wrap the rope around the flange and tighten the rope to secure the fan.
Intake & Exhaust This duct fan can be used as an intake machine or exhaust machine in greenhouses and large grow tents. For optimal ventilation of the space, intake fans or openings (without fans) must be placed in the bottom corners of the growing space, and exhaust fans must be hung (as shown below) or mounted in the corresponding highest corners. Make sure the airflow arrow of the intake fan points towards the growing space and the arrow of the exhaust fan points away from the growing space.
Controller Power Up and Setting Step 1: Mark the locations to be mounted with the mounting holes on the controller. Pay attention to the fan power cable length and the probe length. Step2: Drill 2 holes at the marked locations. Step3: If you need plastic expansion tubes, insert the included 2 expansion tubes into the drilled holes and fix them in the holes with a hammer. Step4: Align the mounting holes on the controller with the wall anchor, and insert the two screws with a screwdriver or drill.
Step5: You can organize your cables using the included tie bracket, screws, and cable ties. Use screws to secure the cable tie to the surface. Wrap the cable tie around the rope and put it into the tie bracket. Step6: Insert the probe of the duct fan into the WORK1/WORK2 port of the controller. Step7: Insert the temperature and humidity sensor probe into the P1/P2 port of the controller. Then, place the probe near the plant in the grow tent for the most accurate reading.
Add More Fans This smart controller can control two fans simultaneously. Insert the two fans into the WORK1 and WORK 2 ports separately, as shown below: Dual Connection IVC-001W T6 IVC-001W T6 Cleaning & Maintenance Step2: Use a wet cloth to remove dust and debris from the wind circle and fan blades. Step1: Remove the power supply chassis from the flange. (See steps 1 and 2 in the installation instructions on how to remove the power supply chassis.
Step3: Remove dust and debris from the other side of the stator blade and clean the inner areas of the intake and exhaust flanges. Step4: See steps 7 to 9 in the installation instructions to secure the power supply chassis on the flange. 14 FCC Requirement Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with Part 15 of the FCC Rules.
– Reorient or relocate the receiving antenna. – Increase the separation between the equipment and receiver. – Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. – Consult the dealer or an experienced radio/TV technician for help. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body.
Attached Table 2: Parameter Description In Automatic Mode Icon CF：F Function Setting Range Default Setting Temperature Unit Fan Speed ℃ or ℉ 0~10 -40℃~100℃/-40℉~212℉ or OFF (disable high-temperature trigger) 40℃~100℃/-40℉~212℉ or OFF (disable low-temperature trigger) ℉ 10 High Temp. High-temperature trigger value Low Temp. Low-temperature trigger value High Temp. Alarm High-temperature alarm value Low Temp. Alarm Low-temperature alarm value Temp.
V1.
