Installation Instructions

INID SmartProx readers
Specifications
Power Supply
7.5 - 20 Volt DC (12 VDC recommended)
Power consumption
model average peak
INID SmartProx 0.75 W 1.3 W
INID SmartProx PIN 0.75 W 1.6 W
Current consumption @12 VDC
1)
model average peak
INID SmartProx 60 mA 105 mA
INID SmartProx PIN 60 mA 130 mA
1)
Use Ohm's law to calculate current at different voltages.
Dimensions
143 x 50 x 25 mm / 5.63 x 2 x 1 inch
Material
UL94-V0 rated LEXAN
®
925U
Operating temperature
-25° to 65° C / -15° to 150° F
Protection class
IP54 Complete protection against contact,
protection against dust deposit. Protection
from splashed water.
Models
article number
5200 INID SmartProx reader WG/C&D/TTL 500-5200
5210 INID SmartProx reader RS485/RS422 500-5210
5220 INID SmartProx reader RS232 500-5220
5240 INID SmartProx PIN reader WG/C&D/TTL 500-5240
5250 INID SmartProx PIN reader RS485/RS422 500-5250
5260 INID SmartProx PIN reader RS232 500-5260
Parts list (1 each)
1. Reader front
2. Mounting backplate
3. Enclosure screw
4. Installation sheet
5. Configuration sheet
Cable specifications (non-shielded)
interface
maximum
cable length
min.conductor size
with 12 V supply
meters feet mm
2
AWG
Wiegand
61 200 0.16 25
91 300 0.24 23
152 500 0.40 21
Clock/Data 25 80
0.25 24
TTL serial 1.5 5
RS232 2.4 8
RS485/RS422
(cable power)
61 200
152 500 0.34 22
RS485/RS422
(local power)
1220 4000 0.25 24
For locally powered readers the minimum conductor size is
0.16mm
2
, or AWG 25 for all distances and interfaces.
Features
• INID readers have a slim mullion mountable
design and are designed for both in- and outdoor
use. The INID reader can be mounted on any
surface without significant performance
degradation. For mounting to a metal surface
however, a non-metallic spacer is advised.
• The switch mode power supply of the reader
accepts a wide range input from 7.5 - 20 VDC.
Higher supply voltages result in lower current
consumption and allow for cost effective wiring
with a smaller conductor diameter.
• Reader output formats are determined by the
configuration switches of the reader.
• Separate models are available for card-only and
card+PIN.
• Electrical interface options for WG/C&D/TTL
serial, RS485/RS422 and RS232 are available
with separate models.
PIN code
INID PIN readers provide several options for PIN
data formats and output protocols. The card and
PIN code data is sent separately and independently
allowing host system determined operation for
card-only, PIN-only and card and PIN usage.
Indications
User feedback is provided by a single LED bar and a
multi-tone sounder. User feedback is controllable by
the host system. PIN models are equipped with
back lighting of the PIN code digits for usage in
dark environments.
Operation
When a proximity card is read successfully the card
associated code is send to the Host system, the LED
bar lights briefly and the sounder sounds a short
tone.
When a PIN is entered the data is transmitted; at
each key press a click sound is produced and the
LED bar lights briefly. The back light of the PIN code
lights up after a successful card read or at the first
key press.
The LED bar and the buzzer are also controllable by
the Host system.
INID SmartProx readers - installation and operation manual version 1.05; March 28, 2014