User's Guide

ManualsBrandsINGICS ManualsElectronicsCard Beacon

INGICS TECHNOLOGY

Guide

Ver.0b

iBS06 User Guide

Introduction

The document is a guide for iBS06. To quickly verify it, please download INGICS iBS01 Tag

Utility APP from below link(Android only):

https://play.google.com/store/apps/details?id=com.ingics.tag.igstagconﬁg

Overview

Operation

Basically, iBS06 will always transmit BLE payload in the conﬁgured time interval(by default is 5s) after power on. The

transmitted BLE payload/message is then received and uploaded to the internet/cloud server by the beacon gateway, such

as iGS01S or iGS03W/M/E..

Power on

Two CR2012 batteries are pre-installed in each iBS06 beacon at shipment. Please remove the isolation plastic sheet to

power on it. You will see the LED ﬂash when powered on. At power on, the user can conﬁgure it within 20 seconds.

INGICS TECHNOLOGY CO., LTD. • SUPPORT@INGICS.COM • WWW.INGICS.COM

Summary of content (7 pages)

PAGE 1
INGICS TECHNOLOGY iBS06 User Guide Guide Ver.0b Introduction The document is a guide for iBS06. To quickly verify it, please download INGICS iBS01 Tag Utility APP from below link(Android only): https://play.google.com/store/apps/details?id=com.ingics.tag.igstagconfig Overview Operation Basically, iBS06 will always transmit BLE payload in the configured time interval(by default is 5s) after power on.
PAGE 2
INGICS TECHNOLOGY Power off Just pull out the battery slot to power off iBS06. LED Description LED behavior Power on ( Start of Configuration mode) Red “blinking” End of Configuration mode Green “blinking” Beacon connected for configuration Green “ON” Verifying 1. Power on iBS06 2. Open iBS01 Tag Utility APP and Press “START SCAN”. 3. Wait for a while, you should see the BLE payload of iBS06 received by the APP. Below is an explanation of the payload shown in the APP. INGICS TECHNOLOGY CO., LTD.
PAGE 3
INGICS TECHNOLOGY Battery Level iBS06 uses two pieces of CR2012 coin battery as the power source. It consumes only a little power and keeps working for a long time. Below is a suggestion for translating the battery voltage to the remaining capacity at room temperature. Capacity Voltage High >2.9V Middle >2.7V Low >2.6V Change battery <=2.6V Remember, a proper filtering on the voltage is necessary. Change the battery 1. Pull out the battery slot 2. Change the new batteries.
PAGE 4
INGICS TECHNOLOGY 3. Plug the battery slot into iBS06. *PLEASE MAKE SURE THE POLARITY IS CORRECT.. Configuration When powered on, iBS06 will be in configuration mode for 20 sec. Users can use iBS01 Tag Utility to scan and connect iBS06 to configure the transmit power and ADV(advertising) interval. Steps 1. Power on iBS06 (if iBS06 is already powered on, please power off it first then power on again) 2. Press the CONFIG icon on the up-right corner of the utility within 20 secs.
PAGE 5
INGICS TECHNOLOGY NFC(MIFARE) location Waste Electrical and Electronic Equipment Recycling Our product is compliant with the WEEE directive for re-use/recovery/recycling. This cross-out wheeled-bin symbol is a reminder that this product should not be treated as household waste. Instead hand it over to the appropriate collection point for the recycling of electrical and electronic equipment in accordance with local environmental regulations for waste disposal.
PAGE 6
INGICS TECHNOLOGY Statement Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
PAGE 7
INGICS TECHNOLOGY INGICS TECHNOLOGY CO., LTD. • SUPPORT@INGICS.COM • WWW.INGICS.