User's Guide

ManualsBrandsINGICS ManualsElectronicsSensor Beacon

INGICS TECHNOLOGY

Guide

Ver.0c

iBS05 User Guide

Introduction

The document is a guide for iBS05/iBS05G/iBS05H/iBS05T. To quickly verify it, please download INGICS iBS01

Tag Utility APP from below link(Android only):

https://play.google.com/store/apps/details?id=com.ingics.tag.igstagconﬁg

Overview

Operation

Basically, iBS05 will always transmit BLE payload in the conﬁgured time interval(by default, iBS05/05G is 5s and iBS05H/05T

is 30s) in the background after power on. The transmitted BLE payload/message is then received and uploaded to the

internet/cloud server by the beacon gateway, such as iGS01S or iGS03W/M/E. Besides background transmission, button or

sensor status change will also trigger an immediate BLE transmission for monitoring the sensor in real time.

Power on

iBS05 is in standby mode at shipping. You can power on it by pressing the front button. The LED will ﬂash “Red” to indicate it

is powered on. After power on, the button becomes the alarm button.

Power off

When necessary, users can power off iBS05 by applying a pencil with a blunt tip to the rubber button on the bottom side. The

LED will ﬂash “Orange” to indicate it is powered off and entering the standby mode.

INGICS TECHNOLOGY CO., LTD. • SUPPORT@INGICS.COM • WWW.INGICS.COM

Summary of content (6 pages)

PAGE 1
INGICS TECHNOLOGY iBS05 User Guide Guide Ver.0c Introduction The document is a guide for iBS05/iBS05G/iBS05H/iBS05T. To quickly verify it, please download INGICS iBS01 Tag Utility APP from below link(Android only): https://play.google.com/store/apps/details?id=com.ingics.tag.igstagconfig Overview Operation Basically, iBS05 will always transmit BLE payload in the configured time interval(by default, iBS05/05G is 5s and iBS05H/05T is 30s) in the background after power on.
PAGE 2
INGICS TECHNOLOGY Alarm Button After power on, the front button acts as an alarm button. As pressing the button, the LED will light up “green” and trigger an immediate BLE transmission with the button activation event. As the back end server received this status change, it can be used as a warning or alarming.
PAGE 3
INGICS TECHNOLOGY transmitting the temperature value in the configured time interval . Verifying 1. Power on iBS05 2. Open iBS01 Tag Utility APP and Press “START SCAN”. 3. Wait for a while, you should see the BLE payload of iBS05 received by the APP. Below is an explanation of the payload shown in the APP. Battery Level iBS05 uses a CR2032 coin battery as the power source. It consumes only a little power and keeps working for a long time.
PAGE 4
INGICS TECHNOLOGY Configuration When powered on, iBS05 will be in configuration mode for 20 sec. Users can use iBS01 Tag Utility to scan and connect iBS05 to configure the transmit power and ADV(advertising) interval. Steps 1. Power on iBS05 (if iBS05 is already powered on, please power off it first then power on again) 2. Press the CONFIG icon on the up-right corner of the utility within 20 secs. Select iBS05 for configuration. 3. In the SETTING page, you can configure TX power and ADV interval.
PAGE 5
INGICS TECHNOLOGY Statement Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
PAGE 6
INGICS TECHNOLOGY Revision History DATE REVISION CHANGES May 30, 2021 0a Initial release June 2, 2021 0b Add Waste Electrical and Electronic Equipment Recycling section for appropriate recycling the equipment Aug 2, 2021 0c Fix typo, modify LED section, and add Working mode section INGICS TECHNOLOGY CO., LTD. • SUPPORT@INGICS.COM • WWW.INGICS.