Variable speed MODEL MODÈLE MODELO DS 12DVF • DS 14DVF CORDLESS DRIVER DRILL PERCEUSE-VISSEUSE À BATTERIE TALADRO ATORNILLADOR A BATERÍA DS14DVF SAFETY INSTRUCTIONS AND INSTRUCTION MANUAL WARNING IMPROPER OR UNSAFE use of this power tool can result in death or serious bodily injury! This manual contains important information about product safety. Please read and understand this manual BEFORE operating the power tool.
English CONTENTS Page IMPORTANT SAFETY INFORMATION .............. 3 MEANINGS OF SIGNAL WORDS ...................... 3 SAFETY .................................................................... GENERAL SAFETY RULES – FOR ALL BATTERY OPERATED TOOLS ..................... SPECIFIC SAFETY RULES AND SYMBOLS ....... IMPORTANT SAFETY INSTRUCTIONS FOR BATTERY CHARGER ........................... IMPORTANT SAFETY INSTRUCTIONS FOR USE OF THE BATTERY AND BATTERY CHARGER ....................................
English IMPORTANT SAFETY INFORMATION Read and understand all of the safety precautions, warnings and operating instructions in the Instruction Manual before operating or maintaining this power tool. Most accidents that result from power tool operation and maintenance are caused by the failure to observe basic safety rules or precautions. An accident can often be avoided by recognizing a potentially hazardous situation before it occurs, and by observing appropriate safety procedures.
English SAFETY GENERAL SAFETY RULES – FOR ALL BATTERY OPERATED TOOLS WARNING: Read and understand all instructions. Failure to follow all instructions listed below, may result in electric shock, fire and/or serious personal injury. SAVE THESE INSTRUCTIONS 1. 2. 3. 4 Work Area (1) Keep your work area clean and well lit. Cluttered benches and dark areas invite accidents. (2) Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust.
English 4. 5. Tool Use and Care (1) Use clamps or other practical way to secure and support the workpiece to a stable platform. Holding the work by hand or against your body is unstable and may lead to loss of control. (2) Do not force tool. Use the correct tool for your application. The correct tool will do the job better and safer at the rate for which it is designed. (3) Do not use tool if switch does not turn it on or off.
English SPECIFIC SAFETY RULES AND SYMBOLS 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 6 Hold tools by insulated gripping surfaces when performing an operation where the cutting tool may contact hidden wiring. Contact with a “live” wire will make exposed metal parts of the tool “live” and shock the operator. ALWAYS wear ear plugs when using the tool for extended periods. Prolonged exposure to high intensity noise can cause hearing loss.
English 14. NEVER use a tool which is defective or operating abnormally. If the tool appears to be operating unusually, making strange noises, or otherwise appears defective, stop using it immediately and arrange for repairs by a Hitachi authorized service center. 15. Carefully handle power tools. Should a power tool be dropped or struck against hard materials inadvertently, it may be deformed, cracked, or damaged. 16. Do not wipe plastic parts with solvent.
English IMPORTANT SAFETY INSTRUCTIONS FOR BATTERY CHARGER 1. 2. 3. 4. 5. 6. 7. 8. This manual contains important safety and operating instructions for battery charger Model UC9SD, UC12SD and UC14SD. Before using battery charger, read all instructions and cautionary markings on (1) battery charger, (2) battery, and (3) product using battery. To reduce risk of injury, charge HITACHI rechargeable battery type EB1212S and EB1214L for UC12SD and EB1412S and EB1414 for UC14SD.
English 10. Do not operate battery charger if it has received a sharp blow, been dropped, or otherwise damaged in any way; take it to a qualified serviceman. 11. Do not disassemble battery charger; take it to a qualified serviceman when service or repair is required. Incorrect reassembly may result in a risk of electric shock or fire. 12. To reduce risk of electric shock, unplug charger from receptacle before attempting any maintenance or cleaning. Removing the battery will not reduce this risk.
English DISPOSAL OF THE EXHAUSTED BATTERY WARNING: Do not dispose of the exhausted battery. The battery must explode if it is incinerated. The product that you have purchased contains a rechargeable battery. The battery is recyclable. At the end of it’s useful life, under various state and local laws, it may be illegal to dispose of this battery into the municipal waste stream. Check with your local solid waste officials for details in your area for recycling options or proper disposal.
English FUNCTIONAL DESCRIPTION NOTE: The information contained in this Instruction Manual is designed to assist you in the safe operation and maintenance of the power tool. NEVER operate, or attempt any maintenance on the tool unless you have first read and understood all safety instructions contained in this manual. Some illustrations in this Instruction Manual may show details or attachments that differ from those on your own power tool.
English 䡬 Battery Terminal Hole Terminal Hole Nameplate Nameplate Latch Latch Fig. 1 2. Battery Charger (UC12SD and UC14SD) Air vent Battery Installation Hole Cord Pilot Lamp Plug Name Plate Caution Plate Fig.
English SPECIFICATIONS 1. Cordless Driver Drill Model DS12DVF DS14DVF Motor DC motor No-load speed Capacity Drilling Screw Driver Low 0–350/min 0–400/min High 0–1050/min 0–1200/min Wood (Thickness 11/16" (18mm)) 13/16"(21mm) (Soft Wood) 1"(25mm) (Soft Wood) Metal (Thickness 1/16" (1.6mm)) 15/32" (12mm) (Mild Steel) 15/32" (12mm) (Mild Steel) 19/32" (15mm) (Aluminum) 19/32" (15mm) (Aluminum) Wood screw #12 × 2-1/2" (5.5mm × 63mm) #12 × 2-1/2" (5.
English ASSEMBLY AND OPERATION APPLICATIONS 䡬 䡬 Use as a drill Drilling of soft steel, wood, plastic and aluminum materials. Use as a screwdriver Tightening and loosening of machine screws, wood screws and tapping screws. REMOVAL AND INSTALLATION METHOD OF BATTERY 䡬 䡬 How to install the battery. Align the battery with the groove in tool handle and slip it into place.
English 1. Insert the battery to the battery charger. Insert the battery into the battery charger as shown in Fig. 4. Make sure it contacts the bottom of the battery charger. Battery Battery Pilot Lamp Pilot Lamp Fig. 4 2. Insert the plug of battery charger into the receptacle. WARNING: Do not use the electrical cord if damaged. Have it repaired immediately. 3.
English CAUTION: Do not pull the plug out of the receptacle by pulling on the cord. Make sure to grasp the plug when removing from receptacle to avoid damaging cord. 5. Remove the battery from the battery charger. Supporting the battery charger with hand, pull out the battery from the battery charger. 䢇 䢇 CAUTION: When the battery charger has been continuosly used, the battery charger will be heated, thus constituting the cause of the failures.
English OPERATION 1. Mounting and dismounting of the bit (1) Mounting the bit Insert a screwdriver bit etc. into the keyless drill chuck. Firmly grasp the ring and tighten the sleeve by turning it toward the right (in the clockwise direction as viewed from the front). (See Fig.5) Tighten NOTE: If the sleeve becomes loose during operation, tighten it further. The tightening force becomes stronger when the sleeve is tightened. Loosen Ring Sleeve Fig.
English 4. Change rotation speed High speed Low speed Shift knob Shift knob Fig. 7 Fig. 8 Operate the shift knob to change the rotational speed. Move the shift knob in the direction of the arrow (see Figs. 7 and 8). When the shift knob is set to “LOW”, the drill rotates at a low speed. When set to “HIGH”, the drill rotates at a high speed. 䢇 䢇 CAUTION: When changing the rotational speed with the shift knob, confirm that the switch is off.
English mark CAUTION: 䢇 The cap cannot be set between the numbers “1, 3, 5 ... 22” or the black dot. 䢇 Do not use with the cap set at the black line between the ”. Doing so may number “22” and the drill mark “ cause damage. (See Fig. 10) Black line Fig. 10 6. Tightening torque adjustment (1) Tightening torque Tightening torque should correspond in its intensity to the screw diameter. When too strong power is used, the screw head may be broken or be injured.
English THE SCOPE AND SUGGESTIONS FOR USES Table 3 Work Cap position Suggestions Wood Drilling Steel Use for drilling purpose. Aluminum Screw tightening Machine screw 1 – 22 Use the bit and socket matching the screw diameter. Wood screw 1– Use after drilling a pilot hole. HOW TO SELECT TIGHTENING TORQUE Table 4 Cap position Tightening torque 1 Approximately 9 in-lbs. (10 kg-cm) 3 Approximately 15 in-lbs. (17 kg-cm) 7 Approximately 23 in-lbs. (26 kg-cm) 13 Approximately 35 in-lbs.
English MAINTENANCE AND INSPECTION CAUTION: Pull out battery before doing any inspection or maintenance. 1. Checking the condition of the bit The bits should be checked regularly. If worn or broken bits can slip or decrease the efficiency of the motor and burn it out. Replace worn bits with new ones. CAUTION: If you use a driver bit of which point is worn or broken, it will be dangerous since it slips. So replace it with a new one. 2. Check the Screws Loose screws are dangerous.
English ACCESSORIES WARNING: ALWAYS use Only authorized HITACHI replacement parts and accessories. NEVER use replacement parts or accessories which are not intended for use with this tool. Contact HITACHI if you are not sure whether it is safe to use a particular replacement part or accessory with your tool. The use of any other attachment or accessory can be dangerous and could cause injury or mechanical damage. NOTE: Accessories are subject to change without any obligation on the part of the HITACHI.
English OPTIONAL ACCESSORIES.....sold separately 1. Battery (EB1212S, EB1214L) (For DS12DVF) 2. Battery (EB1412S, EB1414) (For DS14DVF) NOTE Specifications are subject to change without any obligaiton on the part of the HITACHI.
Français INFORMATIONS IMPORTANTES DE SÉCURITÉ Lire et comprendre toutes les précautions de sécurité, les avertissements et les instructions de fonctionnement dans ce mode d’emploi avant d’utiliser ou d’entretenir cet outil motorisé. La plupart des accidents causés lors de l’utilisation ou de l’entretien de l’outil motorisé proviennent d’un non respect des règles ou précautions de base de sécurité.
Français SÉCURITÉ RÈGLES GÉNÉRALE DE SÉCURITÉ – POUR TOUS LES OUTILS FONCTIONNANT SUR BATTERIE AVERTISSEMENT: Lire et comprendre toutes les instructions. Un non respect de toutes les instructions ci-dessous peut entraîner une électrocution, un incendie et/ou de sérieuses blessures personnelles. CONSERVER CES INSTRUCTIONS 1. 2. 3. Zone de travail (1) Garder la zone de travail propre et bien éclairée. Les établis mal rangés et les zones sombres invitent aux accidents.
Français 4. 5. Utilisation de l’outil et entretien (1) Utiliser un étau ou toutes autres façons de fixer et maintenir la pièce à usiner sur une plate-forme stable. Tenir la pièce avec la main ou contre son corps est instable et peut conduire à une perte de contrôle de l’outil. (2) Ne pas forcer sur l’outil. Utiliser l’outil correct pour l’application souhaitée. L’outil correct réalisera un meilleur et plus sûr travail dans le domaine pour lequel il a été conçu.
Français RÈGLES DE SÉCURITÉ SPÉCIFIQUES ET SYMBOLES 1. 2. Tenir les outils par les surfaces de grippage lors de la réalisation d’opération où l’outil de coupe risque d’entrer en contact avec des câbles cachés ou son propre cordon. Un contact avec un fil “sous tension” mettra les parties métalliques de l’outil “sous tension” et électrocutera l’utilisateur. TOUJOURS porter des bouchons d’oreille lors de l’utilisation de l’outil pendant de longues périodes.
Français 12. Ne pas utiliser les outils motorisés si le revêtement de plastique ou la poignée est fendu. Des fentes dans le revêtement ou la poignée peuvent entraîner une électrocution. De tels outils ne doivent pas être utilisés avant d’être réparé. 13. Les lames et les accessoires doivent être fermement montés sur l’outil. Éviter les blessures potentielles personnelles et aux autres.
Français CONSIGNES DE SÉCURITÉ IMPORTANTES POUR LE CHARGEUR DE BATTERIE 1. 2. 3. 4. 5. 6. 7. 8. Ce manuel renferme des consignes de sécurité et d’utilisation importantes pour le chargeur de batterie modèle UC9SD, UC12SD et UC14SD. Avant d’utiliser le chargeur de batterie, lire toutes les étiquettes d’instruction et de précaution apposées sur (1) le chargeur de batterie, (2) la batterie, et (3) le produit utilisant la batterie.
Français 9. Ne pas utiliser le chargeur si son cordon ou sa fiche sont endommagés - Le remplacer immédiatement. 10. Ne pas utiliser le chargeur s’il a reçu un coup, s’il est tombé ou endommagé de toute autre manière. L’apporter à un réparateur qualifié. 11. Ne pas démonter le chargeur ni le produit qui reçoit la batterie ; si un entretien ou des réparations sont nécessaires, les apporter à un réparateur qualifié. Un remontage incorrect pourrait provoquer une décharge électrique ou un feu. 12.
Français 12. TOUJOURS alimenter le chargeur sur une prise secteur domestique standard (120 volts). L’utilisation du chargeur à une autre tension peut entraîner une surchauffe et endommager le chargeur. 13. TOUJOURS attendre au moins 15 minutes entre deux recharges pour éviter toute surchauffe du chargeur. 14. TOUJOURS débrancher le cordon d’alimentation de la prise secteur lorsqu’on ne se sert pas du chargeur.
Français DESCRIPTION FONCTIONNELLE REMARQUE: Les informations contenues dans ce mode d’emploi sont conçues pour assister l’utilisateur dans une utilisation sans danger et un entretien de l’outil motorisé. NE JAMAIS utiliser ni entreprendre une révision de l’outil sans avoir d’abord lu et compris toutes les instructions de sécurité contenues dans ce manuel. Certaines illustrations dans ce mode d’emploi peuvent montrer des détails ou des accessoires différents de ceux de l’outil motorisé utilisé.
Français 䡬 Batterie Orifice de prise Orifice de prise Plaque signalétique Plaque signalétique Taquet Taquet Fig. 1 2. Chargeur de batterie (UC12SD et UC14SD) Évent d’air Orifice d’installation de la batterie Cordon Lampe témoin Fiche Plaque Plaque de précaution signalétique Fig.
Français SPECIFICATIONS 1.
Français ASSEMBLAGE ET FONCTIONNEMENT UTILISATIONS 䡬 䡬 Utilisation comme mèche Perçage d’acier doux, de bois, de plastique et d’aluminium. Utilisation comme tournevis Serrage et desserrage de vis à métaux, vis en bois et vis auto-taraudeuses. MÉTHODE DE RETRAIT ET D’INSTALLATION DE LA BATTERIE 䡬 䡬 Installation de la batterie Aligner la batterie sur la fente de la poignée de l’outil et la glisser à l’intérieur. Toujours insérer la batterie à fond, jusqu’à ce qu’elle se bloque avec un petit déclic.
Français 1. Insérer la batterie dans le chargeur de batterie. Insérer la batterie dans le chargeur de batterie comme indiqué à la Fig. 4. Bien s’assurer qu’elle touche le fond du chargeur de batterie. Batterie Batterie Lampe témoin Lampe témoin Fig. 4 2. Brancher la fiche du chargeur de batterie dans la prise. AVERTISSEMENT: Ne pas utiliser le cordon électrique s’il est endommagé. Le faire réparer immédiatement. 3.
Français 4. Débrancher le chargeur de batterie de la prise. PRÉCAUTION : Ne pas débrancher la fiche de la prise en tirant sur le cordon. Pour éviter tout dommage lorsqu’on débranche la fiche de la prise, bien tenir la fiche proprement dite. 5. Retirer la batterie du chargeur de batterie. Sortir la batterie du chargeur tout en la soutenant de la main. PRÉCAUTION : Si le chargeur a fonctionné pendant longtemps de suite, il sera chaud, ce qui risque de provoquer des pannes.
Français UTILISATION 1. Pose et dépose du foret (1) Pose du foret Insérer le foret, etc. dans le mandrin sans clavette. Saisir fermement la bague et serrer le manchon en le tournant vers la droite (à l’avant). (Voir Fig. 5) Serrer REMARQUE: Si le manchon se relâche pendant le fonctionnement, le serrer davantage . La force de serrage sera plus forte si le manchon est bien serré. Desserrer Anneau Manehon Fig.
Français 4. Changement de vitesse de rotation Vitesse élevée Vitesse ralentie Bouton de décalage Bouton de décalage Fig. 7 Fig. 8 Actionnez le bouton de décalage pour changer la vitesse de rotation. Enfoncez le bouton de blocage pour relâcher le blocage et déplacez le bouton de décalage dans la direction de la flèche (Voir les Fig. 7 et 8). Quand le bouton de décalage est mis sur “LOW” (petite vitesse), la perceuse tourne à petite vitesse.
Français Indice de PRÉCAUTION: 䢇 Le capot ne peut pas être réglé entre les nombres “1, 3, 5 ... 22” ou le point blanc. 䢇 Pour éviter tout dommage, ne pas utiliser avec le capot réglé avec le filet noir entre le nombre “22“ et l’indice de ”. (Voir Fig. 10.) forage “ Filet noir Fig. 10 6. Réglage du couple de serrage (1) Couple de serrage Le couple de serrage devra correspondre au diamètre de la vis utilisée.
Français PLAGE D’UTILISATION ET SUGGESTIONS Tableau 3 Position du capuchon Travail Suggestions Bois Perçage Acier Utilisation à des fins de perçage. Aluminium Vissage Vis à métaux 1 – 22 Utiliser la mèche et la douille correspondant au diamètre de la vis. Vis en bois 1– Utiliser après avoir percé un trou d’amorce.
Français ENTRETIEN ET INSPECTION PRÉCAUTION: Sortir la batterie avant toute opération d’inspection ou d’entretien. 1. Vérifier l’état de la mèche Les mèches doivent être vérifiées régulièrement. Si elles sont usées ou cassées, elles risquent de glisser ou de réduire le rendement du moteur et de le brûler. Remplacer les mèches usées par des neuves. PRÉCAUTION: Si l’on utilise une mèche dont la pointe est usée ou cassée, elle sera dangereuse car elle risque de glisser. La remplacer par une neuve. 2.
Français ACCESSOIRES AVERTISSEMENT: TOUJOURS utiliser UNIQUEMENT des pièces de rechange et des accessoires HITACHI. Ne jamais utiliser de pièce de rechange ou d’accessoires qui ne sont pas prévus pour être utilissl avec cet outil. En cas de doute, contacter HITACHI pour savoir si une pièce de rechange ou un accessoire particulier peuvent être utilisés en toute sécurité avec votre outil.
Français ACCESSOIRES EN OPTION.....vendus séparément 1. Batterie (EB1212S, EB1214L) (Pour DS12DVF) 2. Batterie (EB1412S, EB1414) (Pour DS14DVF) REMARQUE: Les spécifications sont sujettes à modification sans aucune obligation de la part de HITACHI.
Español INFORMACIÓN IMPORTANTE SOBRE SEGURIDAD Antes de utilizar o de realizar cualquier trabajo de mantenimiento de esta herramienta eléctrica, lea y comprenda todas las precauciones de seguridad, advertencias e instrucciones de funcionamiento de este Manual de instrucciones. La mayoría de los accidentes producidos en la operación y el mantenimiento de una herramienta eléctrica se deben a la falta de observación de las normas o precauciones de seguridad.
Español SEGURIDAD NORMAS GENERALES DE SEGURIDAD – PARA TODAS LAS HERRAMIENTAS ALIMENTADAS CON BATERÍA ADVERTENCIA: Lea y entienda todas las instrucciones. Si no sigue las instrucciones indicadas a continuación, pueden producirse descargas eléctricas, incendios, y/o lesiones serias. GUARDE ESTAS INSTRUCCIONES. 1. 2. 3. 46 Área de trabajo (1) Mantenga el área de trabajo limpia y bien iluminada. Los bancos de trabajo desordenados y las áreas obscuras pueden conducir a accidentes.
Español 4. 5. Utilización y cuidados de la herramienta (1) Utilice abrazaderas u otra forma práctica de asegurar y sujetar la pieza de trabajo sobre una plataforma estable. La sujeción de la pieza de trabajo con la mano o contra su cuerpo puede ser inestable y conducir a la pérdida del control. (2) No fuerce la herramienta. Utilice la herramienta correcta para su aplicación. Con la herramienta correcta realizará mejor el trabajo y ésta será más segura para la velocidad para la que ha sido diseñada.
Español NORMAS Y SÍMBOLOS ESPECÍFICOS DE SEGURIDAD 1. 2. 3. Sujete las herramientas por las superficies de empuñadura aisladas cuando realice una operación en la que la herramienta de corte pueda entrar en contacto con cables ocultos. El contacto con un conductor “activo” “activará” las partes metálicas de la herramienta y el operador recibirá una descarga eléctrica. SIEMPRE utilice tapones para los oídos cuando tenga que utilizar la herramienta durante mucho tiempo.
Español 13. Las cuchillas y los accesorios deberán montarse con seguridad en la herramienta. Evite lesiones personales y de otras personas. Las cuchillas, los accesorios de corte, y demás accesorios montados en la herramienta deberán fijarse con seguridad. 14. NO utilice NUNCA una herramienta defectuosa o que funcione anormalmente. Si la herramienta parece que funciona anormalmente, produciendo ruidos extraños, etc.
Español INSTRUCCIONES IMPORTANTES DE SEGURIDAD PARA EL CARGADOR DE BATERÍAS 1. 2. 3. 4. 5. 6. 7. 8. Este manual contiene instrucciones importantes de seguridad para el cargador de baterías modelo UC9SD, UC12SD y UC14SD. Antes de utilizar el cargador de baterías, lea todas las instrucciones y tenga en cuenta las marcas de precaución de (1) el cargador de baterías, (2) la batería, y (3) el producto que utiliza la batería.
Español 9. No utilice el cargador de baterías con un cable o un enchufe dañado. Si están dañados, reemplácelos inmediatamente. 10. No utilice el cargador de baterías si ha recibido un golpe, si ha caído, o si está dañado de alguna otra forma. Llévelo a un técnico cualificado. 11. No desarme el cargador de baterías. Cuando necesite reparación, llévelo a un técnico cualificado. El reensamblaje incorrecto podría resultar en el riesgo de incendios o descargas eléctricas. 12.
Español 14. SIEMPRE desconecte el cable de alimentación del tomacorriente cuando no vaya a utilizar el cargador. ELIMINACIÓN DE LAS BATERÍAS AGOTADAS ADVERTENCIA: No tire las baterías agotadas. Las baterías pueden explotar si se incineran. El producto que ha adquirido contiene una batería. La batería es reciclable.
Español DESCRIPCIÓN FUNCIONAL NOTA: La información contenida en este Manual de instrucciones ha sido diseñada para ayudarle a utilizar con seguridad y mantener esta herramienta eléctrica. NUNCA haga funcionar ni efectúe el mantenimiento de la herramienta antes de leer y comprender todas las instrucciones de seguridad contenidas en este manual. Algunas ilustraciones de este Manual de Instrucciones pueden mostrar detalles o accesorios diferentes a los de la propia herramienta eléctrica.
Español 䡬 Batería Orificio de terminal Orificio de terminal Placa de características Place de características Cierre Cierre Fig. 1 2. Cargador de baterías (UC12SD y UC14SD) Rejillas de ventilación Orificio de instalación de la batería Cable Lámpara piloto Clavija Placa de Placa de precaución características Fig.
Español ESPECIFICACIONES 1.
Español MONTAJE Y OPERACIÓN APLICACIONES 䡬 䡬 Utilización como taladro Taladrado de materiales de acero dulce, madera, plástico, y aluminio Utilización como destornillador Apriete y aflojado de tornillos para metal, tornillos para madera, y tornillos autorroscantes. MÉTODO DE EXTRACCIÓN E INSTALACIÓN DE LA BATERÍA 䡬 䡬 Forma de instalar la batería Alinee la batería con la ranura de la empuñadura de la herramienta y deslícela en su lugar.
Español 1. Inserte la batería en el cargador de baterías. Inserte la batería en el cargador de baterías como se muestra en la Fig. 4. Cerciórese de que haya quedado en contacto con la base del cargador de baterías. Batería Batería Lámpara piloto Lámpara piloto Fig. 4 2. Inserte el enchufe del cargador de baterías en un tomacorriente. ADVERTENCIA: No utilice el cargador si su cable está dañado. Haga que se lo reparen inmediatamente. 3.
Español 4. Desconecte el cargador de baterías del tomacorriente. PRECAUCIÓN: No desconecte el cable del tomacorriente tirando delmismo. Cerciórese de tirar del enchufe para desconectarlo del tomacorriente a fin de evitar dañar el cable. 5. Extraiga la batería del cargador de baterías. Sujetando el cargador de baterías con una mano, extraiga la batería del mismo. ● ● PRECAUCIÓN: Si utiliza continuamente el cargador de baterías, éste se calentará, lo que puede causar averías.
Español OPERACIÓN 1. Montaje y desmontaje de la broca Anillo Apretar (1) Montaje de la broca Inserte una broca de destornillador, etc., en el portabroca sin llave. Sujete firmemente el anillo y apriete el manguito girándolo hacia la derecha (visto desde el frente). (Consulte la Fig. 5) Aflojar NOTA: Si el manguito se llegara a aflojar durante la operación, vuélvalo a apretar. La fuerza de apriete se vuelve mayor al apretarse el manguito. Manguito Fig.
Español 4. Cambio de velocidad de rotación Velocidad baja Velocidad alta Mando de cambio Fig. 7 Mando de cambio Fig. 8 Operar la perilla de cambio para cambiar la velocidad de rotación. Oprimir el botón de cierre para desenganchar el cerrojo y mover la perilla de cambio en la dirección de la flecha (Ver la Figs. 7 y 8). Cuando la perilla de cambio se deja en “LOW”, el taladro gira despacio, mientras que en la marca “HIGH” gira rápidamente.
Español Marca del 䢇 䢇 PRECAUCIÓN La tapa no podrá ajustarse entre los números “1, 3, 5 ... 22” o el punto negro. No utilice la unidad con la tapa ajustada en la línea negra, ”. Esto entre el número “22” y la marca de taladro “ podría producir daños. (Consulte la Fig.10). Línea negra Fig. 10 6. Ajuste del par de apriete (1) Par de apriete La intensidad del par de apriete deberá corresponder con el diámetro del tornillo. Cuando se utiliza un par excesivo el tornillo se romperá o se dañará su cabeza.
Español ALCANCE Y SUGERENCIAS PARA LA UTILIZACIÓN Tabla 3 Trabajo Posición de la tapa Sugerencias Madera Taladrado Acero Utilización para fines de taladrado. Aluminium Apriete de tornillos Tornillo para metales 1 – 22 Utilice la broca y el cubo adecuados al diámetro del tornillo. Tornillos para madera 1– Utilice después de haber taladrado un orificio piloto. FORMA DE SELECCIONAR EL PAR DE APRIETE Tabla 4 Posición de la tapa Par de apriete 1 Aproximadamente 9 in-lbs.
Español MANTENIMIENTO E INSPECCIÓN PRECAUCIÓN: Extraiga la batería antes de realizar cualquier trabajo de inspección o de mantenimiento. 1. Comprobación de las condiciones de la broca Las brocas deberán comprobarse regularmente. Si una broca está desgastada o rota, puede patinar o reducir la eficacia del motor, o hacer que se queme. Reemplace las brocas gastadas por otras nuevas. PRECAUCIÓN: Si utiliza una broca de destornillador con su punta desgastada o rota, puede resultar peligroso, porque patinará.
Español ACCESSORIOS ADVERTENCIA: UTILICE únicamente repuestos y accesorios autorizados por HITACHI. No utilice nunca repuestos o accesorios no previstos para usar con esta herramienta. Si tiene dudas en cuanto a la seguridad de usar determinado repuesto o accesorio junto con su herramienta, póngase en contacto con HITACHI. La utilización de otros accesorios puede resultar peligrosa y causar lesiones o daños mecánicos.
Español ACCESORIOS OPCIONALES.....de venta por separado 1. Batería (EB1212S, EB1214L) (Para DS12DVF) 2. Batería (EB1412S, EB1414) (Para DS14DVF) NOTA: Las especificationes están sujetas a cambio sin ninguna obligación por parte de HITACHI.
18 503 502 501 19 8 20 39 33 22 32 21 9 34 30 31 36 25 37 12 2 24 11 35 10 23 1 38 13 14 4 40 26 41 15 3 5 16 27 6 17 28 7 42 29 A B C 1 318-228 1 2 312-516 1 3 320-660 1 4 320-661 1 5 318-232 1 6 312-709 1 7 312-714 1 8 312-713 1 9 318-230 1 10 319-744 6 11 306-936 6 12 312-715 1 13 312-705 1 14 312-704 1 15 312-697 1 16 315-817 1 17 311-962 1 18 315-137 1 19 315-805 1 20 315-816 1 21 315-804 1 22 315-815 1 23 315-136 1 24 312-716 1 25 318-231 1 26 318-244 1
18 503 502 501 19 8 20 39 33 22 32 21 9 34 30 31 36 25 37 12 2 24 11 35 10 23 1 38 13 14 4 40 26 41 15 3 5 16 27 6 17 28 7 42 29 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 A DS14DVF B 318-228 312-516 320-660 320-661 318-232 312-709 312-714 312-713 318-230 319-744 306-936 312-715 312-705 312-704 312-697 315-817 311-962 315-137 315-805 315-816 315-804 315-815 315-136 312-716 318-231 320-648 991-672 ———— 318-
Please contact HITACHI KOKI U.S.A. LTD. at 1-800-59-TOOLS (toll free), or HITACHI AUTHORIZED POWER TOOL SERVICE CENTER recarding COLLECTION. Pour le RAMASSAGE, contacter HITACHI KOKI U.S.A. LTD. au 1-800-59-TOOLS (appel gratuit), ou UN SERVICE APRES-VENTE D’OUTILS ELECTRIQUE AGREE PAR HITACHI. Con respecto a la RECOLECCIÓN de baterías, póngase en contacto con HITACHI KOKI U.S.A. LTD. número 1-800-59-TOOLS (llamada gratis), o con HITACHI AUTORIZED POWER TOOL SERVICE CENTER. Issued by Hitachi Koki Co.