User's Manual

ManualsBrandsIndyme Solutions ManualsElectronicsWireless Help Button

Technical Document

430710-00

Rev. H

Indyme Solutions, Inc. 8295 Aero Place  San Diego, CA 92123 U +1.858.268.0717  +1.800.829.6141 Page 1 of 5

CB982 Wireless Help button

Programming and Installation Instructions

Overview

The CB982 is a member of the Global Solutions Family. Indyme GSF products operate in the

800MHz – 900MHz frequency spectrum. The CB982 is a 1-button, GSF Help button designed for

use at Customer Service locations. GSF Help buttons are designed to communicate with a GSF

Access Point. GSF products are not compatible with legacy devices

Programming Parameters

GSF products MUST be properly programmed to establish communication. Programming parameters

MUST match your configuration. The default settings are for testing purposes only and should not be

used. Failure to properly program your help button and access point will prevent your devices from

working.

GSF Help buttons have three primary programming parameters; Netcode, Address and Operating

Mode. These MUST be programmed in the correct order to establish communication and ensure

proper operation. Identify the parameters for your configuration before you begin programming.

Using the programming instructions below set the following parameters in order.

 Netcode – unique identification code for the installation environment.

 Address – alarm number associated with a control unit alarm event.

 Operating Mode – defines how the help button will respond when activated.

Programming a help button requires a series of button presses. The specific buttons vary by help button type. On

the CB982, SET is the “PRESS HERE” button and RESET is a small square below the SET button. The assurance LED

is red and is located above the SET button. This LED will flash during programming to indicate your progress.

Netcode

*00000001

Address

*0001

Operating Mode

* Default parameters are for testing purposes only.

CB982

RESET

LED

Summary of content (5 pages)

PAGE 1
Technical Document 430710-00 Rev. H CB982 Wireless Help button Programming and Installation Instructions CB982 Overview The CB982 is a member of the Global Solutions Family. Indyme GSF products operate in the 800MHz – 900MHz frequency spectrum. The CB982 is a 1-button, GSF Help button designed for use at Customer Service locations. GSF Help buttons are designed to communicate with a GSF Access Point.
PAGE 2
430710-00 Rev. H Technical Document GSF Help button Programming GSF Help buttons function in the 800MHz – 900MHz frequency spectrum. These wireless transceivers, communicate with the CB951 Access Point. Each help button MUST be programmed with the correct parameters to match the CB951 Access Point(s). Help buttons use a hierarchy based menu structure. You must enter the Programming Menu first, to select the desired submenu. Each submenu may have one or more options available.
PAGE 3
Technical Document 430710-00 Rev. H Menu-2: Learn Mode Allows the help button to capture the Netcode from another GSF device; (help button or access point). All help buttons and access points must have the same Netcode to communicate. After entering the Programming Menu; Press the SET button two times for Menu-2, RESET once to save. The LED will flash twice to indicate Menu-2 was selected. The LED will then begin flashing. ¼ second on, 1 second off.
PAGE 4
Technical Document 430710-00 Rev. H Installation and Trouble shooting 1. Identify all programming characteristics before you begin programming or installation.  Netcode  Help button Addresses  Help button Modes 2. Program the required parameters into the CB951 Access Points first. 3. Use the first CB951 Access Point to clone the Netcode to all of the help buttons. This will ensure the same Netcode is being assigned to all devices.
PAGE 5
Technical Document 430710-00 Rev. H FCC Notice of Compliance This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.