User's Manual

ManualsBrandsIndyme Solutions ManualsElectronicsWireless Help Button

Technical Document

430708-00

Rev. H

Indyme Solutions, Inc. 8295 Aero Place  San Diego, CA 92123 USA +1.858.268.0717  +1.800.829.6141Page 1 of 5

CB938 Wireless Help Button

Programming and Installation Instructions

Overview

The CB938 is a member of the Global Solutions Family. Indyme GSF products operate in the 800MHz –

900MHz frequency spectrum. The CB938 is a 1-button, GSF Help button designed for use at Customer

Service locations. GSF Help buttons are designed to communicate with a GSF Access Point. GSF

products are not compatible with legacy devices

Programming Parameters

GSF products MUST be properly programmed to establish communication. Programming

parameters MUST match your configuration. The default settings are for testing

purposes only and should not be used. Failure to properly program your help button and

access point will prevent your devices from working.

GSF Help buttons have three primary programming parameters; Netcode, Address and

Operating Mode. These MUST be programmed in the correct order to establish

communication and ensure proper operation. Identify the parameters for your

configuration before you begin programming.

Using the programming instructions below set the following parameters in order.

 Netcode – unique identification code for the installation environment.

 Address – alarm number associated with a control unit alarm event.

 Operating Mode – defines how the help button will respond when activated.

Programming a help button requires a series of button presses. The specific buttons vary by

device type. On the CB938, SET is the “Press Here” button and RESET is a small circle near the

bottom of the call box. The assurance LED is red and is located above the SET button. This LED

will flash during programming to indicate your progress.

Netcode

*00000001

Address

*0001

Operating Mode

* Default parameters are for testing purposes only.

CB938

RESET

LED

Summary of content (5 pages)

PAGE 1
Technical Document 430708-00 Rev. H CB938 Wireless Help Button Programming and Installation Instructions CB938 Overview The CB938 is a member of the Global Solutions Family. Indyme GSF products operate in the 800MHz – 900MHz frequency spectrum. The CB938 is a 1-button, GSF Help button designed for use at Customer Service locations. GSF Help buttons are designed to communicate with a GSF Access Point.
PAGE 2
430708-00 Rev. H Technical Document GSF Help button Programming GSF Help buttons function in the 800MHz – 900MHz frequency spectrum. These wireless transceivers, communicate with the CB951 Access Point. Each help button MUST be programmed with the correct parameters to match the CB951 Access Point(s). Help buttons use a hierarchy based menu structure. You must enter the Programming Menu first, to select the desired submenu. Each submenu may have one or more options available.
PAGE 3
Technical Document 430708-00 Rev. H Menu-2: Learn Mode Allows the help button to capture the Netcode from another GSF device; (help button or access point). All help buttons and access points must have the same Netcode to communicate. After entering the Programming Menu; Press the SET button two times for Menu-2, RESET once to save. The LED will flash twice to indicate Menu-2 was selected. The LED will then begin flashing. ¼ second on, 1 second off.
PAGE 4
Technical Document 430708-00 Rev. H Installation and Trouble shooting 1. Identify all programming characteristics before you begin programming or installation. 2. 3. 4. 5. 6.  Netcode  Help button Addresses  Help button Modes Program the required parameters into the CB951 Access Points first. Use the first CB951 Access Point to clone the Netcode to all of the help buttons. This will ensure the same Netcode is being assigned to all devices.
PAGE 5
Technical Document 430708-00 Rev. H FCC Notice of Compliance This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.