User's Manual

ManualsBrandsIndyme Solutions ManualsElectronicsWireless help button

Technical Document

430673-02

Rev. G

Indyme Solutions, Inc. 8295 Aero Place  San Diego, CA 92123 USA +1.858.268.0717  +1.800.829.6141 Page 1 of 7

CB932 Wireless Help Button

Programming and Installation Instructions

Introduction

The CB932 is a member of the Global Solutions Family. Indyme GSF

products operate in the 800MHz – 900MHz frequency spectrum. The

CB932 is a 1-button, GSF help button designed for use at customer

service or sales floor locations. GSF Help Buttons are designed to

communicate with a GSF Access Point. GSF products are not

compatible with legacy devices.

Hardware

 (2) #6 x 3/4” Phillips screw

 (2) #6 plastic wall anchor

 (2) strips, double sided adhesive

 (1) package alcohol swap

 (2) AA alkaline battery

Programming Parameters

GSF products MUST be properly programmed to establish communication. Programming parameters MUST

match your configuration. The default settings are for testing purposes only and should not be used. Failure

to properly program your help button and access point will prevent your devices from working.

GSF Help buttons have three primary programming parameters; Netcode, Address and Operating Mode.

These MUST be programmed in the correct order to establish communication and ensure proper operation.

Identify the parameters for your configuration before you begin programming.

Using the programming instructions below set the following parameters in order.

 Netcode – unique identification code for the installation environment.

 Address – alarm number associated with a control unit alarm event.

 Operating Mode – defines how the help button will respond when activated.

Programming a help button requires a series of button presses. The specific buttons vary by device type.

On the CB932, SET is the “large button in the middle” and RESET is “the black outer cover”. The

assurance LED is red and is located BEHIND to the SET button. This LED will flash during programming

to indicate your progress.

Netcode

*00000001

Address

*0001

Operating Mode

* Default parameters are for testing purposes only.

CB932

RESET

SET

Summary of content (7 pages)

PAGE 1
Technical Document 430673-02 Rev. G CB932 Wireless Help Button Programming and Installation Instructions CB932 Introduction The CB932 is a member of the Global Solutions Family. Indyme GSF products operate in the 800MHz – 900MHz frequency spectrum. The CB932 is a 1-button, GSF help button designed for use at customer service or sales floor locations. GSF Help Buttons are designed to communicate with a GSF Access Point. GSF products are not compatible with legacy devices.
PAGE 2
GSF Help button Programming GSF Help buttons function in the 800MHz – 900MHz frequency spectrum. These wireless transceivers, communicate with the CB951 Access Point. Each help button MUST be programmed with the correct parameters to match the CB951 Access Point(s). Help buttons use a hierarchy based menu structure. You must enter the Programming Menu first, to select the desired submenu. Each submenu may have one or more options available.
PAGE 3
Menu-2: Learn Mode Allows the help button to capture the Netcode from another GSF device; (help button or access point). All help buttons and access points must have the same Netcode to communicate. After entering the Programming Menu; Press the SET button two times for Menu-2, RESET once to save. The LED will flash twice to indicate Menu-2 was selected. The LED will then begin flashing. ¼ second on, 1 second off. This indicates that the help button is requesting a Netcode.
PAGE 4
Installation Technical Document 1. Identify all programming characteristics before you begin programming or installation.  Netcode  Help button Addresses  Help button Modes 2. Program the required parameters into the CB951 Access Points first. 3. Use the first CB951 Access Point to clone the Netcode to all of the help buttons. This will ensure the same Netcode is being assigned to all devices. You may also clone the Netcode from a known working help button to all other help buttons.
PAGE 5
Install the Help button 1. Verify help button placement with the Store Manager and according to provided instructions. Determine the best mounting method before installing the help button, verify address programming.  Wall Mount  Counter Top Mount 2. The CB932 has four (4) mounting orientation options available; please see pictures below. Choose the appropriate option for your situation. The CB932 mounting bracket MUST be used for all installations.
PAGE 6
Inserting Graphics into the Button Dome Technical Document Included with this help button is a collection of button graphics that can be exchanged prior to installation. The button dome was designed with alignment tabs inside to allow easy orientation alignment and installation. 1. Select the desired graphic from the collection. 2. Determine the mounting orientation of the help button from the pictures above; F, C, or P. 3.
PAGE 7
Technical Document FCC Notice of Compliance This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.