CAS GPS Node II User Manual PROD1116 DOCU0142 Rev D Wabtec Digital Mining Technology PO Box 5107 Fountaindale, New South Wales Australia, 2261 t +61 2 4336 1800 f +61 2 4336 1888 www.getransportation.
CAS-GPS Node II User Manual CONTENTS 1 Document Revision ...........................................................................................................................................................4 1 Warnings ...........................................................................................................................................................................5 2 Manufacturer Details .....................................................................................
CAS-GPS Node II User Manual 10.4 DISPOSAL .................................................................................................................................................................16 11 AUTHORIZED REPRESENTATIVES .....................................................................................................................................17 12 WARRANTY TERMS .....................................................................................................................
CAS-GPS Node II User Manual 1 DOCUMENT REVISION Amendment Log Issue No.
CAS-GPS Node II User Manual 1 WARNINGS Installation should be in accordance with the installation procedures defined by Wabtec Digital Mining Technology and must only be performed by authorized and qualified installers. The CAS product is a driver’s aid and should not be relied upon as the primary means of reducing the risks of high potential interactions. Interactions include between Heavy Vehicles, Light Vehicles, infrastructure and personnel.
CAS-GPS Node II User Manual 3 SCOPE This user manual covers the following variants of the CAS-GPS node product range. All PROD1116 products are electrically equivalent with differences residing in available connection methods to suit the various installations of the product.
CAS-GPS Node II User Manual 3.4 CAS-GPS NODE ToF VARIANTS (xx) The CAS-GPS Node family of products are also available with optional high accuracy Time-of-Flight (ToF) RF proximity detection. PROD1116-τν(X)(xx) PROD1116-τνX PROD1116-τνXNT PROD1116-τν PROD1116-τνNT 3.
CAS-GPS Node II User Manual 5 STORAGE Where the equipment is not to be installed immediately, proper storage is important to ensure protection of equipment and validity of warranty. All equipment should be stored indoors, protected from the elements in a cool dry area. If storing on the ground, ensure that the storage area is not an area where water will collect.
CAS-GPS Node II User Manual 9 THE CAS GPS NODE PRODUCT FAMILY 9.1 PRINCIPLE OF SYSTEM OPERATION The CAS-GPS Intelligent multi-purpose NODE is the front-end transponder for enabling situational awareness of fleet vehicles, infrastructure and personnel. The NODES form an integral component of the CAS-GPS system when paired with one of the CAS-GPS host devices such as the light vehicle display or the heavy vehicle rugged IVU running the CAS-GPS user interface software.
CAS-GPS Node II User Manual 9.2.1.1 Type S Node - Standby Mode Standby Mode is a low power state which is activated shortly after the PDA has shutdown. A configurable amount of time (default 15 minutes) after the vehicle ignition has been switched off, the light vehicle display will be shutdown. A few minutes after that, the CAS-GPS system will enter Standby Mode. The CAS-GPS system will return to full power operation once the vehicle ignition has been switched on.
CAS-GPS Node II User Manual 9.2.4 PROD1116-Pν(X)(xx) – Type P Node The Versatile Type P Node contains a magnetic base which communicates with the CAS-GPS User Interface via wireless Personal Area Network connection. The unit is battery powered for mobile use or can be wired to a 12V-24Vdc power supply for fixed position installations. For mobile use in Light Vehicle mobile installations, this unit can be deployed on a daily basis with a fully charged battery.
CAS-GPS Node II User Manual 9.3 9.3.1 CAS-GPS NODE OPERATION On System Start-up Immediately after starting the system and before putting it into service, perform a quick check of the CAS-GPS user interface status ICONs.
CAS-GPS Node II User Manual 9.3.2 Vehicle in Motion When your vehicle is moving, you can operate using your normal safe operating procedures. The Display will sound an alarm to gain your attention if there is another vehicle that is getting too close. A quick glance at the display will show the location, type, ID, heading and speed of other vehicles. You cannot silence the alarm whilst your vehicle is in motion. 9.3.
CAS-GPS Node II User Manual 9.5 TYPE P NODE INSTALLATION The Type P Node is attached to the vehicle using a magnetic base.
CAS-GPS Node II User Manual 9.6 SYSTEM CHARGING WARNINGS Only use charge cables provided. Charging can be plugged into a normal vehicle 12V accessory power outlet. Charging can be carried out during operation. Do not pass charging cable through vehicle doors or windows. Do not use damaged power cords or plugs. Do not bend or damage the power cord. Do not touch the power cord with wet hands or disconnect the charger by pulling the cord. Do not Short-Circuit the Charger or the Battery.
CAS-GPS Node II User Manual 10 SERVICE, MAINTENANCE & DISPOSAL 10.1 EQUIPMENT SERVICE 10.1.1 Display Unit • • • • Clean screen surface with a clean dry soft cloth - Do not use solvents or cleaners on the screen surface! Check for physical damage to screen surface. Check the cable is securely connected to the d i s p l a y . Check the mounting bracket is secure – finger tighten only if loose. 10.1.
CAS-GPS Node II User Manual 11 AUTHORIZED REPRESENTATIVES Brazil Sub Sahara Africa GE Transportes Ferroviários S.A Avenida General David Sarnoff, n 4600 Probe Integrated Mining Technologies (PTY) Ltd Cidade Industrial Contagem, MG 32210110 Brazil P: +55 31 2103 5348 F: +55 31 2103 5100 www.getransportation.com/mining 245 Albert Amon Road Meadowdale Germiston 1614 P: +27 11 453 0924 F: +27 11 453 2141 www.probebattery.co.
CAS-GPS Node II User Manual 12 WARRANTY TERMS Equipment and Parts: 15 months from delivery, or 12 months from when system is placed in service (whichever occurs first). Modifications to this product without written consent from the manufacturer or its designated authorised representatives will void all warranty obligations.
CAS-GPS Node II User Manual 13 REGULATORY INFORMATION Warning: Modifications to this product without written consent from the manufacturer or its designated authorised representatives could void the user’s authority to operate the equipment 13.1 DECLARATION OF CONFORMITY WITH FCC RULES FOR ELECTROMAGNETIC COMPATIBILITY Supplier's Declaration of Conformity 47 CFR § 2.
CAS-GPS Node II User Manual 13.1.2 Federal Communication Commission (FCC) - Radiation Exposure Statement To comply with FCC RF exposure limits for general population / uncontrolled exposure, the antennas used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. 13.2 INDUSTRY CANADA COMPLIANT This Class B digital apparatus complies with Canadian ICES-003.
CAS-GPS Node II User Manual 13.5 LIFE SUPPORT POLICY These products are not designed for use in life support appliances, devices, or systems where malfunction of these products can reasonably be expected to result in personal injury. Wabtec Digital Mining Technology customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Wabtec Digital Mining Technology from any and all damages resulting from such improper use or sale. 13.
