Instructions for use Washer-dryer ! GB English,1 PL Polski,43 FR Français,15 NL Nederlands,57 XWDE 861480 DE Deutsch,29 CZ Česky,71 This symbol reminds you to read this instruction manual.
Installation GB ! This instruction manual should be kept in a safe place for future reference. If the washer-dryer is sold, transferred or moved, make sure that the instruction manual remains with the machine so that the new owner is able to familiarise himself/ herself with its operation and features. Levelling the machine correctly will provide it with stability, help to avoid vibrations and excessive noise and prevent it from shifting while it is operating.
Connecting the drain hose 65 - 100 cm Connect the drain hose, without bending it, to a drainage duct or a wall drain located at a height between 65 and 100 cm from the floor; alternatively, rest it on the side of a washbasin or bathtub, fastening the duct supplied to the tap (see figure). The free end of the hose should not be underwater.
Care and maintenance GB Cutting off the water and electricity supplies • Turn off the water tap after every wash cycle. This will limit wear on the hydraulic system inside the washer-dryer and help to prevent leaks. • Unplug the washer-dryer when cleaning it and during all maintenance work. Cleaning the washer-dryer • The outer parts and rubber components of the appliance can be cleaned using a soft cloth soaked in lukewarm soapy water. Do not use solvents or abrasives.
Precautions and tips ! This washer-dryer was designed and constructed in accordance with international safety regulations. The following information is provided for safety reasons and must therefore be read carefully. General safety • This appliance was designed for domestic use only.
Description of the washer-dryer GB Control panel START/PAUSE button and indicator light ON/OFF button TEMPERATURE button DISPLAY WASH CYCLE Detergent dispenser drawer SELECTOR KNOB PUSH&WASH+DRY button SPIN button DELAYED START OPTION button buttons DRYING button Detergent dispenser drawer: used to dispense detergents and washing additives (see “Detergents and laundry”). DELAYED START button: press to set a delayed start for the selected wash cycle; the delay period appears on the display.
Display GB B A C D The display is useful when programming the machine and provides a great deal of information. The duration of the available wash cycles and the remaining time of a running cycle appear in section A; if the DELAYED START option has been set, the countdown to the start of the selected wash cycle will appear.
How to run a wash cycle or a drying cycle GB Rapid programming 1. LOAD THE LAUNDRY. Open the porthole door. Load the laundry, making sure you do not exceed the maximum load value indicated in the table of programmes and wash cycles on the following page. 2. ADD THE DETERGENT. Pull out the detergent dispenser drawer and pour the detergent into the relevant compartments as described in “Detergents and laundry”. 3. CLOSE THE DOOR. 4. Press the “PUSH&WASH+DRY” button to start the programme.
Wash cycles and options Table of wash cycles Prewash Wash Fabric softener Bleach 600 800 1000 1000 0 800 800 4 3 3,5 3,5 1 2 3,5 - - 4 5 3,5 3,5 1 2 3,5 Standard 7 Cottons with Pre-wash: extremely soiled whites.
GB Push&Wash+Dry This function makes it possible to start an automatic wash and drying cycle either when the machine is off without having to press the ON/OFF button in advance, or after switching on the machine without having activated any button and/or selector (otherwise the Push&Wash+Dry function will be deactivated). To start the Push&Wash+Dry cycle press and hold the button for 2 seconds. The indicator lights up to show that the cycle has started.
Detergents and laundry Detergent dispenser drawer Special wash cycles Successful washing results also depend on the correct dose of detergent: adding too much detergent will not necessarily result in a more efficient wash, and may in fact cause build up on the inside of your appliance and contribute to environmental pollution. ! Do not use hand washing detergents because these create too much foam. ! Use powder detergent for white cotton garments, for prewashing, and for washing at temperatures over 60°C.
GB Eco Synthetic (programme 12) ideal for mixed loads (cotton and synthetics) with a normal soil level. The effective performance levels achieved at cold temperatures are guaranteed by a mechanical action which operates at varying speed, across set average intervals. Wash&Dry 45’ select programme 13 for washing and drying lightly soiled garments (Cotton and Synthetic) in a short time. This cycle may be used to wash and dry a laundry load of up to 1 kg in just 45 minutes.
Troubleshooting Your washer-dryer could occasionally fail to work. Before contacting the Technical Assistance Service (see “ Service”), make sure that the problem cannot be solved easily using the following list. Problem: Possible causes / Solutions: The washer-dryer does not switch • The appliance is not plugged into the socket fully, or not enough to make contact. on. • There is no power in the house. The wash cycle does not start. • • • • • The washer-dryer door is not closed properly.
Service GB Before contacting the Technical Assistance Service: • Check whether you can solve the problem alone (see “Troubleshooting”). • Restart the wash cycle to check whether the problem has been solved. • If this is not the case, contact an authorised Technical Assistance Centre. ! Always request the assistance of authorised technicians. Have the following information to hand: • the type of problem; • the appliance model (Mod.); • the serial number (S/N).
Mode d’emploi Lavante-séchante ! FR Français Ce symbole vous rappelle de lire ce mode d’emploi.
Installation FR ! Conserver ce mode d’emploi pour pouvoir le consulter à tout moment. En cas de vente, de cession ou de déménagement, veiller à ce qu’il suive toujours le lavante-séchante pour que son nouveau propriétaire soit informé sur son mode de optionnement et puisse profiter des conseils correspondants. ! Lire attentivement les instructions: elles fournissent des conseils importants sur l’installation, l’utilisation et la sécurité de l’appareil. Déballage et mise à niveau Déballage 1.
Raccordement du tuyau de vidange 65 - 100 cm Raccorder le tuyau d’évacuation, sans le plier, à un conduit d’évacuation ou à une évacuation murale placés à une distance du sol comprise entre 65 et 100 cm ; ou bien l’accrocher à un évier ou à une baignoire, dans ce cas, fixer le support en plastique fourni avec l’appareil au robinet (voir figure). L’extrémité libre du tuyau d’évacuation ne doit pas être plongée dans l’eau.
Entretien et soin FR Coupure de l’arrivée d’eau et du courant • Fermer le robinet de l’eau après chaque lavage. Cela réduit l’usure de l’installation hydraulique du lavante-séchante et évite tout danger de fuites. • Débrancher la fiche de la prise de courant lors de tout nettoyage du lavante-séchante et pendant tous les travaux d’entretien. Nettoyage du lavante-séchante • Pour nettoyer l’extérieur et les parties en caoutchouc, utiliser un chiffon imbibé d’eau tiède et de savon.
Précautions et conseils ! Ce lavante-séchante a été conçu et fabriqué conformément aux normes internationales de sécurité. Ces consignes sont fournies pour des raisons de sécurité, il faut les lire attentivement. • Ne mettez pas à sécher du caoutchouc-mousse ou des élastomères du même genre. • Vérifiez qu’au cours du séchage, le robinet de l’eau soit bien ouvert. Sécurité générale Mise au rebut • Cet appareil est conçu pour un usage domestique.
Description du lavante-séchante FR Bandeau de commandes Touche et voyant START/PAUSE Touche TEMPÉRATURE Touche ON/OFF ECRAN Touche Tiroir à produits lessiviels BOUTON PROGRAMMES Touche PUSH&WASH+DRY Tiroir à produits lessiviels : pour charger les produits lessiviels et les additifs (voir “Produits lessiviels et linge”). Touche ON/OFF : appuyer brièvement sur la touche pour allumer ou éteindre l’appareil. Le voyant vert START/ PAUSE clignotant lentement indique que la machine est allumée.
Ecran FR B A C D L’écran est utile pour programmer la machine et fournit de multiples renseignements. La section A affiche la durée des différents programmes disponibles et, une fois le cycle lancé, le temps restant jusqu’à la fin du programme ; si un DÉPART DIFFÉRÉ a été sélectionné, le temps restant avant le démarrage du programme sélectionné est affiché.
Comment effectuer un cycle de lavage ou un séchage FR Programmation rapide 1. CHARGER LE LINGE. Ouvrir la porte hublot. Charger le linge en faisant attention à ne pas dépasser la quantité indiquée dans le tableau des programmes de la page suivante. 2. DOSER LE PRODUIT LESSIVIEL. Sortir le tiroir et placer le produit lessiviel dans les bacs correspondants comme indiqué au paragraphe “Produits lessiviels et linge”. 3. FERMER LE HUBLOT. 4. Appuyer sur la touche « Push&Wash+Dry » pour lancer le programme.
Programmes et options Automatique 13 Lavege&Séchage 45’ 14 Rafraîchissement Fonctions Rinçage/Blanchiment 600 800 1000 1000 0 800 800 4 3 3,5 3,5 1 2 3,5 - - 4 5 3,5 3,5 1 2 3,5 90° 60° (Max.
FR Push&Wash+Dry Cette fonction permet de lancer un cycle de lavage et de séchage automatique même si la machine est éteinte sans qu’il faille préalablement appuyer sur la touche ON/OFF ou, après allumage de la machine, sans avoir besoin d’activer aucune autre touche et/ou bouton (autrement le programme Push&Wash+Dry sera désactivé). Pour lancer le cycle Push&Wash+Dry appuyer 2 secondes de suite sur la touche. L’allumage du voyant signale que le cycle est lancé.
Produits lessiviels et linge Tiroir à produits lessiviels Programmes spéciaux Un bon résultat de lavage dépend aussi d’un bon dosage de produit lessiviel : un excès de lessive ne lave pas mieux, il incruste l’intérieur du lavante-séchante et pollue l’environnement. ! Ne pas utiliser de lessives pour lavage à la main, elles moussent trop. ! Utiliser des lessives en poudre pour du linge en coton blanc et en cas de prélavage et de lavages à une température supérieure à 60°C.
FR Eco Coton 20° (programme 11) idéal pour des charges de linge sale en coton. Les bonnes performances, même à froid, comparables à celles d’un lavage à 40°, sont assurées grâce à une action mécanique qui brasse en variant la vitesse et avec des pics répétés et rapprochés. Eco Synthétiques (programme 12) idéal pour des charges mixtes (coton et synthétiques) moyennement sales.
Anomalies et remèdes Il peut arriver que le lavante-séchante ne fonctionne pas bien. Avant d’appeler le Service de dépannage (voir “Assistance”), contrôler s’il ne s’agit pas par hasard d’un problème facile à résoudre à l’aide de la liste suivante. Anomalies : Causes / Solutions possibles : Le lavante-séchante ne s’allume pas. • La fiche n fest pas branchée dans la prise de courant ou mal branchée. • Il y a une coupure de courant. Le cycle de lavage ne démarre pas.
Assistance FR Avant d’appeler le service d’Assistance technique : • Vérifier s’il est possible de résoudre l’anomalie par ses propres moyens (voir “Anomalies et Remèdes”); • Remettre le programme en marche pour contrôler si l’inconvénient a disparu ; • Si ce n’est pas le cas, contacter un Centre de dépannage. ! Ne jamais s’adresser à des techniciens non agréés. Communiquer : • le type de panne ; • le modèle de l’appareil (Mod.) ; • le numéro de série (S/N).
Bedienungsanleitungen Waschtrockner ! DE Deutsch Dieses Symbol erinnert Sie daran, das vorliegende Handbuch zu lesen.
Aufstellung DE ! Es ist äußerst wichtig, diese Bedienungsanleitung sorgfältig aufzubewahren, um sie jederzeit zu Rate ziehen zu können. Sorgen Sie dafür, dass sie im Falle eines Umzugs oder einer Übergabe an einen anderen Benutzer das Gerät stets begleitet, damit auch der neue Inhaber die Möglichkeit hat, diese zu Rate zu ziehen. ! Lesen Sie bitte folgende Hinweise aufmerksam durch: sie liefern wichtige Informationen hinsichtlich der Installation, des Gebrauchs und der Sicherheit.
Anschluss des Ablaufschlauches 65 - 100 cm Schließen Sie den Ablaufschlauch, ohne ihn dabei zu knicken, an eine Ablaufleitung, oder an einen in der Wand, in einer Höhe von 65cm bis 100cm an; oder hängen Sie diesen in ein Becken oder eine Wanne ein; befestigen Sie den Schlauch in diesem Falle mittels der mitgelieferten Führung an dem Wasserhahn (siehe Abbildung). Das freie Ablaufschlauchende darf nicht unter Wasser bleiben.
Reinigung und Pflege DE Abstellen der Wasser- und Stromversorgung • Drehen Sie den Wasserhahn nach jedem Waschvorgang zu. Hierdurch wird der Verschleiß der Wasseranlage verringert und Wasserlecks vorgebeugt. • Ziehen Sie den Netzstecker aus der Steckdose, bevor Sie Ihren Waschtrockner reinigen. Reinigung des Gerätes • Die Gehäuseteile und die Teile aus Gummi können mit einem mit warmer Spülmittellauge angefeuchteten Tuch gereinigt werden. Vermeiden Sie den Einsatz von Löse- und Scheuermitteln.
Vorsichtsmaßregeln und Hinweise ! Der Waschtrockner wurde nach den strengsten internationalen Sicherheitsvorschriften entworfen und gebaut. Nachstehende Hinweise werden aus Sicherheitsgründen geliefert und sollten aufmerksam gelesen werden. Allgemeine Sicherheit • Dieses Gerät wurde ausschließlich für den Einsatz im privaten Haushalt konzipiert.
Beschreibung Ihres Waschtrockner DE Taste mit Kontrollleuchte START/PAUSE Bedienblende Taste TEMPERATUR ON/OFF-Taste DISPLAY Waschmittelschublade Taste WÄHLSCHALTER PROGRAMME PUSH&WASH+DRY Waschmittelschublade: für Waschmittel und Zusätze (siehe “Waschmittel und Wäsche”). Taste ON/OFF : Drücken Sie kurz auf die Taste, um das Gerät ein- bzw. auszuschalten. Die Kontrollleuchte START/PAUSE, die langsam grün blinkt, zeigt an, dass das Gerät eingeschaltet ist.
Display B DE A C D Das Display dient nicht nur zur Programmierung des Gerätes, sondern liefert auch zahlreiche Informationen. Im Abschnitt A werden die Dauer der verschiedenen verfügbaren Programme sowie die Restzeit nach Zyklusstart angezeigt; wurde eine STARTZEITVORWAHL eingestellt, dann wird die bis zum Start des ausgewählten Programms verbleibende Zeit angezeigt.
Durchführung eines Wasch- oder Trockenzyklus DE Schnellprogrammierung 1.EINFÜLLEN DER WÄSCHE. Öffnen Sie die Gerätetür. Füllen Sie die Wäsche ein. Achten Sie hierbei bitte darauf, die in der Programmtabelle (auf der nächsten Seite) angegebene Wäschemenge nicht zu überschreiten. 2.DOSIERUNG DES WASCHMITTELS. Ziehen Sie die Waschmittelschublade heraus und füllen Sie das Waschmittel in die entsprechenden Kammern (siehe “Waschmittel und Wäsche“). 3. SCHLIESSEN SIE DIE GERÄTETÜR. 4.
Programme und Zusatzfunktionen 30° 30° 60° 40° 30° 40° 30° 600 800 1000 1000 0 800 800 4 3 3,5 3,5 1 2 3,5 - - 4 5 3,5 3,5 1 2 3,5 90° 60° (Max.
DE Push&Wash+Dry Mit dieser Funktion kann ein automatischer Wasch- und Trocknungszyklus auch bei ausgeschalteter Maschine gestartet werden, ohne zuerst die ON/OFF-Taste zu drücken oder ohne, nach dem Einschalten der Maschine, weitere Tasten und/ oder Drehschalter zu betätigen (wird dennoch eine Taste gedrückt, wird das Programm Push&Wash+Dry deaktiviert). Zum Starten des Zyklus Push&Wash+Dry halten Sie die Taste zwei Sekunden lang gedrückt.
Waschmittel und Wäsche Waschmittelschublade Ein gutes Waschergebnis hängt auch von einer korrekten Waschmitteldosierung ab: Eine zu hohe Dosierung bedeutet nicht unbedingt reinere Wäsche, sie trägt nur dazu bei, die Maschineninnenteile zu verkrusten und die Umwelt zu belasten. ! Verwenden Sie keine Handwaschmittel, sie verursachen eine zu hohe Schaumbildung. ! Waschmittel in Pulverform für Baumwollweißwäsche, für die Vorwäsche und für Waschprogramme bei Temperaturen über 60°C verwenden.
DE Eco Baumwolle 20° (programm 11) ideal für normalverschmutze Baumwolle. Die auch mit kaltem Wasser erreichten Leistungen, vergleichbar mit einer Wäsche bei 40°, werden mechanisch erzielt. Die Trommel arbeitet mit wiederholten, kurz auf einander folgenden Beschleunigungen. 20° Mix-Fein (programm 12) ideal für durchschnittlich verschmutze Mischwäsche (Baumwolle und Synthetik). Die guten Waschleistungen auch mit kaltem Wasser werden mechanisch erzielt.
Störungen und Abhilfe Bei Funktionsstörung: Bevor Sie sich an den Technischen Kundendienst wenden (siehe „Kundendienst“), vergewissern Sie sich zuerst, ob es sich nicht um eine Kleinigkeit handelt, die Sie selbst beheben können. Ziehen Sie hierzu nachstehendes Verzeichnis zu Rate. Störungen: Mögliche Ursachen / Lösungen: Der Waschtrockner schaltet sich nicht ein. • Der Stecker steckt nicht in der Steckdose, oder nicht so, dass der Kontakt hergestellt wird. • Der Strom ist ausgefallen.
Kundendienst DE Bevor Sie den Kundendienst anfordern: • sollten einige Kontrollen vorab selbst durchgeführt werden (siehe „Störungen und Abhilfe“); • Starten Sie daraufhin das Programm erneut, um sicherzustellen, dass die Störung auch wirklich behoben wurde; • Ist dies nicht der Fall, wenden Sie sich bitte an ein Kundendienstzentrum. ! Beauftragen Sie bitte niemals unbefugtes Personal. Comunicare: • die Art der Störung; • das Gerätemodell (Mod.); • die Seriennummer (S/N).
Instrukcja obsługi PRALKA ! Ten symbol przypomina o obowiązku zapoznania się z niniejszą PL instrukcją obsługi.
Instalacja PL ! Należy zachować niniejszą książeczkę, aby móc z niej skorzystać w każdej chwili. W przypadku sprzedaży, odstąpienia lub przeniesienia pralki w inne miejsce należy zadbać o przekazanie instrukcji wraz z nią, aby nowy właściciel mógł się zapoznać z działaniem urządzenia i z dotyczącymi go ostrzeżeniami. ! Należy uważnie przeczytać instrukcję obsługi: zawiera ona ważne informacje dotyczące instalacji oraz właściwego i bezpiecznego użytkowania pralki.
Podłączenie przewodu odpływowego 65 - 100 cm Podłączyć przewód odpływowy, nie zginając go, do rury ściekowej lub do otworu odpływowego w ścianie, które powinny się znajdować na wysokości od 65 do 100 cm od podłogi; albo oprzeć go na brzegu zlewu lub wanny, przymocowując do kranu prowadnik, znajdujący się w wyposażeniu pralki (patrz rysunek). Wolny koniec przewodu odpływowego nie powinien być zanurzony w wodzie.
Utrzymanie i konserwacja PL Odłączenie wody i prądu elektrycznego • Zamknąć kurek dopływu wody po każdym praniu. W ten sposób zmniejsza się zużycie instalacji hydraulicznej pralki oraz eliminuje się niebezpieczeństwo wycieków. • Przed przystąpieniem do czyszczenia pralki oraz do czynności konserwacyjnych wyjąć wtyczkę z gniazdka. Czyszczenie pralki • Obudowę zewnętrzną i gumowe części pralki można myć ściereczką zmoczoną w letniej wodzie z mydłem.
Zalecenia i środki ostrożności ! Pralka została zaprojektowana i wyprodukowana zgodnie z międzynarodowymi normami bezpieczeństwa. Niniejsze ostrzeżenia zostały tu zamieszczone ze względów bezpieczeństwa i należy je uważnie przeczytać. Ogólne zasady bezpieczeństwa • Urządzenie to zostało zaprojektowane wyłącznie do użytkowania w warunkach domowych.
Opis pralki PL Panel sterowania Przycisk i kontrolka START/PAUSE Przycisk TEMPERATURA Przycisk ON/OFF WYŚWIETLACZ Szufladka na środki piorące POKRĘTŁO PROGRAMÓW Przycisk PUSH&WASH+DRY Przycisk START Z OPÓŹNIENIEM Przycisk WIROWANIE Przyciski OPCJI Przycisk SUSZENIE Szufladka na środki piorące: do dozowania środków piorących i dodatków (patrz “Środki piorące i bielizna”). Przycisk ON/OFF : nacisnąć krótko przycisk w celu włączenia lub wyłączenia urządzenia.
Wyświetlacz B PL A C D Wyświetlacz pomaga zaprogramować urządzenie i dostarcza wielu informacji. W sekcji A wyświetla się czas trwania dostępnych programów, a po rozpoczęciu cyklu czas, jaki pozostaje do jego zakończenia; natomiast jeśli została ustawiona funkcja START Z OPÓŹNIENIEM, wyświetla się czas pozostający do momentu rozpoczęcia wybranego programu.
Jak wykonać cykl prania lub suszenie PL Szybkie programowanie 1. ZAŁADOWAĆ BIELIZNĘ. Otworzyć drzwiczki. Włożyć bieliznę, uważając, aby nie przekroczyć wielkości wsadu wskazanej w tabeli programów znajdującej się na następnej stronie. 2. WSYPAĆ ŚRODEK PIORĄCY. Wysunąć szufladkę i umieścić środek piorący w odpowiednich komorach zgodnie ze wskazówkami zawartymi w rozdziale “Środki piorące i bielizna”. 3. ZAMKNĄĆ DRZWICZKI. 4. Nacisnąć przycisk “PUSH&WASH+DRY”, aby uruchomić program.
Programy i opcje 8 9 10 11 12 13 14 4 3 3,5 3,5 1 2 3,5 - - 4 5 3,5 3,5 1 2 3,5 1400 6 - 8 1400 6 - - 8 800 1400 1400 800 4 6 6 6 - - 4,5 8 8 8 1400 - 1 1,5 - - - - 1 - Pranie 600 800 1000 1000 0 800 800 1400 6 - - 8 Wirowanie + Odprowadzanie wody - 1400 6 - - - - 8 Tylko Odprowadzanie wody * - OFF - - - - - - 8 * Po wybraniu programu Czas tr
PL Push&Wash+Dry Ta funkcja umożliwia rozpoczęcie automatycznego cyklu prania również przy wyłączonym urządzeniu, bez potrzeby wcześniejszego naciskania przycisku ON/OFF lub, po włączeniu urządzenia, bez potrzeby korzystania z jakiegokolwiek innego przycisku i/lub pokrętła (w przeciwnym wypadku program Push&Wash+Dry zostanie wyłączony). W celu uruchomienia cyklu Push&Wash+Dry, należy przytrzymać przycisk wciśnięty przez 2 sekundy. Włączona kontrolka wskazuje, że cykl jest uruchomiony.
Środki piorące i bielizna Szufladka na środki piorące Dobry rezultat prania zależy również od prawidłowego dozowania środka piorącego: użycie jego nadmiernej ilości nie poprawia skuteczności prania, lecz przyczynia się do powstawania nalotów na wewnętrznych częściach pralki i do zanieczyszczania środowiska. ! Nie stosować środków do prania ręcznego, ponieważ tworzą one za dużo piany.
PL Eco Bawełna 20° (program 11) idealny do zabrudzonej bielizny bawełnianej. Dobre wyniki prania w zimnej wodzie, porównywalne z praniem w 40°, są gwarantowane dzięki działaniu mechanicznemu, wykonywanemu ze zmienną prędkością, której maksymalne wartości powtarzają się w krótkich odstępach czasu. Eco Syntetyczne 20° (program 12) idealny do normalnie zabrudzonej bielizny mieszanej (tkaniny bawełniane i syntetyczne).
Nieprawidłowości w działaniu i sposoby ich usuwania Może się zdarzyć, że pralka nie działa. Przed wezwaniem Serwisu Technicznego (patrz „Serwis Techniczny”) należy sprawdzić, czy problemu nie da się łatwo rozwiązać korzystając z poniższego wykazu. PL Nieprawidłowości w działaniu: Możliwe przyczyny / Rozwiązania: Pralka nie włącza się. Cykl prania nie rozpoczyna się. Pralka nie pobiera wody (Na wyświetlaczu napis H2O).
Serwis Techniczny PL Przed skontaktowaniem się z Serwisem Technicznym: • Sprawdzić, czy problemu nie można rozwiązać samodzielnie (patrz “Nieprawidłowości w działaniu i sposoby ich usuwania”); • Ponownie uruchomić program i sprawdzić, czy problem nie zniknął; • W przeciwnym wypadku skontaktować się z Serwisem Technicznym. ! Nigdy nie wzywać nieautoryzowanych techników. Należy podać: • rodzaj nieprawidłowości; • model urządzenia (Mod.); • numer seryjny (S/N).
Gebruiksaanwijzing WASDROOGMACHINE ! NL Nederlands Dit symbool herinnert u eraan om deze gebruikshandleiding te lezen.
Installatie NL ! Het is belangrijk deze handleiding te bewaren voor latere raadpleging. In het geval u het apparaat verkoopt, of u verhuist, moet het boekje bij de Wasdroogmachine blijven zodat de nieuwe gebruiker de functies en betreffende raadgevingen kan doornemen. ! Lees de instructies aandachtig door: u vindt er belangrijke informatie betreffende installatie, gebruik en veiligheid. Uitpakken en waterpas zetten Uitpakken 1. De Wasdroogmachine uitpakken. 2.
Aansluiting van de afvoerbuis Verbind de buis, zonder hem te buigen, aan een afvoerleiding of aan een afvoer in de muur 65 - 100 cm tussen de 65 en 100 cm van de grond af; of hang hem aan de rand van een wasbak of badkuip, en bind de bijgeleverde steun aan de kraan (zie afbeelding). Het uiteinde van de afvoerslang mag niet onder water hangen.
Onderhoud en verzorging NL Afsluiten van water en stroom • Sluit na iedere wasbeurt de kraan af. Hiermee beperkt u slijtage van de waterinstallatie van de wasmachine en voorkomt u lekkage. • Sluit altijd eerst de stroom af voordat u de Wasdroogmachine gaat schoonmaken en gedurende onderhoudswerkzaamheden. Reinigen van de Wasdroogmachine • De buitenkant en de rubberen onderdelen kunnen met een spons en een lauw sopje worden schoongemaakt. Gebruik nooit schuurmiddelen of oplosmiddelen.
Voorzorgsmaatregelen en advies ! De wasmachine is ontworpen en geproduceerd volgens Afvalverwijdering Algemene veiligheid • De Europese richtlijn 2012/19/EU, betreffende afgedankte elektrische en elektronische apparatuur, voorziet dat huishoudelijke apparatuur niet met het normale afval mag worden meegegeven. De afgedankte apparatuur moet apart worden opgehaald om het wedergebruik van materialen waarvan hij is gemaakt te optimaliseren en om potentiële schade aan de gezondheid en het milieu te voorkomen.
Beschrijving van de Wasdroogmachine NL Bedieningspaneel Knop en controlelampje START/PAUSE Knop Knop ON/OFF TEMPERATUUR DISPLAY Knop Wasmiddelbakje Knop DRAAIKNOP Knop PROGRAMMA’S CENTRIFUGE PUSH&WASH+DRY Wasmiddelbakje: voor wasmiddelen en wasversterkers (zie “Wasmiddelen en wasgoed”). Knop ON/OFF : druk even op de toets om de Wasdroogmachine aan of uit te zetten. Het groen START/PAUSE controlelampje dat langzaam knippert geeft aan dat de Wasdroogmachine aanstaat.
Display B NL A C D Het display is nodig om de Wasdroogmachine te programmeren en geeft meerdere soorten informatie. In de sectie A verschijnt de duur van de beschikbare programma’s en, als de cyclus is gestart, de resterende tijd tot het einde ervan. Indien een UITGESTELDE START is geselecteerd verschijnt de resterende tijd tot aan de start van het geselecteerde wasprogramma.
Het uitvoeren van een was- of droogcyclus NL Snelle programmering 1. HET WASGOED INLADEN. Open de deur. Laad het wasgoed in en zorg ervoor nooit de laadhoeveelheid te overschrijden aangegeven in de programmatabel op de volgende bladzijde. 2. WASMIDDEL DOSEREN.Trek het bakje naar buiten en doe het wasmiddel in de speciale bakjes, zoals aangegeven in “Wasmiddelen en wasgoed”. 3. SLUIT DE DEUR. 4. Druk op de toets “Push&Wash+Dry” om het programma te starten. Traditionele programmering 1.
Programma’s en opties 8 9 10 11 12 Katoen 60° (1): Zeer vuil wit en kleurecht bont wasgoed. Synthetisch: Zeer vuile kleurvaste bonte was. Gekleurd (2) Eco Katoen 20°: Niet zo vuile witte en bonte was. Eco Synthetisch 20° Wassen Wasverzachter Bleken 600 800 1000 1000 0 800 800 4 3 3,5 3,5 1 2 3,5 - - 4 5 3,5 3,5 1 2 3,5 90° 60° (Max.
NL Push&Wash+Dry Met deze functie kunt u een automatische was- of droogcyclus starten terwijl de automaat uit is, zonder dat u daarvóór op de toets ON/OFF hoeft te drukken of, nadien, als u de automaat aanzet, zonder dat u andere toetsen en/of knoppen in hoeft te drukken (als u dit niet doet zal het programma Push&Wash+Dry worden uitgeschakeld). Om de Push&Wash+Dry cyclus te starten houdt u de knop 2 seconden lang ingedrukt. Het ontstoken controlelampje geeft aan dat de cyclus is gestart.
Wasmiddelen en wasgoed Wasmiddelbakje Speciale programma’s Een goed wasresultaat hangt ook af van de juiste dosis wasmiddel: te veel wasmiddel maakt het wassen niet beter. Het wasmiddel blijft aan de binnenzijde van de Wasdroogmachine zitten en zorgt voor het vervuilen van het milieu. ! Gebruik nooit wasmiddelen voor handwas aangezien die te veel schuim vormen. ! Gebruik waspoeder voor witte katoenen was, voor de voorwas en voor het wassen op temperaturen van meer dan 60°C.
NL Gekleurd: gebruik de programma 10 voor het wassen van licht gekleurde was. Het programma is ontwikkeld voor het langdurige behoud van de mooie kleuren van uw wasgoed. Eco Katoen 20° (programma 11) Katoen ideaal voor een lading vuil katoen. De optimale prestaties, zelf met koud water, die kunnen worden vergeleken met een wascyclus op 40°C, worden gegarandeerd door een mechanische werking die de snelheid varieert met herhaaldelijke en zeer dicht op elkaar liggende piekvariaties.
Storingen en oplossingen Het kan gebeuren dat de Wasdroogmachine niet werkt. Voor u contact opneemt met de Servicedienst (zie “Service”) moet u controleren of het niet een storing betreft die u zelf makkelijk kunt verhelpen met behulp van de volgende lijst. Storingen: Mogelijke oorzaken / Oplossing: De Wasdroogmachine gaat niet aan. • De stekker zit niet in het stopcontact of niet ver genoeg om contact te maken. • Het hele huis zit zonder stroom. De wascyclus start niet.
Service NL Voordat u de Servicedienst inschakelt: • Controleer eerst of u het probleem zelf kunt oplossen (zie “Storingen en oplossingen”). • Start het programma opnieuw om te controleren of de storing is verholpen; • Neem indien dit niet helpt contact op met de servicedienst. ! Wendt u nooit tot een niet erkende installateur. Comunicare: • het type storing; • het model Wasdroogmachine (Mod.); • het serienummer (S/N).
Návod k použití PRAČKA ! CZ Česky Tento symbol vám připomíná potřebu přečtení návodu k použití.
Instalace CZ ! Je důležité uschovat tento návod tak, abyste jej mohli kdykoli konzultovat. V případě prodeje, darování nebo přestěhování pračky se ujistěte, že zůstane uložen v blízkosti pračky, aby mohl posloužit novému majiteli při seznámení s její činností a s příslušnými upozorněními. ! Pozorně si přečtěte uvedené pokyny: Obsahují důležité informace týkající se instalace, použití a bezpečnosti při práci. Rozbalení a vyrovnání do vodorovné polohy Rozbalení 1. Rozbalte pračku. 2.
Připojení vypouštěcí hadice 65 - 100 cm Připojte vypouštěcí hadici k odpadovému potrubí nebo k odpadu ve stěně, který se nachází od 65 do 100 cm nad zemí; zamezte jejímu ohybu nebo ji uchyťte k okraji umývadla či vany a připevněte ji ke kohoutu prostřednictvím držáku z příslušenství (viz obrázek). Volný konec vypouštěcí hadice nesmí zůstat ponořený do vody.
Údržba a péče CZ Uzavření přívodu vody a vypnutí elektrického napájení • Po každém praní uzavřete přívod vody. Tímto způsobem dochází k omezení opotřebení pračky a ke snížení nebezpečí úniku vody. • Před zahájením čištění pračky a během operací údržby vytáhněte zástrčku napájecího kabelu z elektrické zásuvky. Čištění pračky • Vnější části a části z gumy se mohou čistit hadrem navlhčeným ve vlažné vodě a saponátu. Nepoužívejte rozpouštědla ani abrazivní látky.
Opatření a rady ! Pračka byla navržena a vyrobena v souladu s platnými mezinárodními bezpečnostním předpisy. Tato upozornění jsou uváděna z bezpečnostních důvodů a je třeba si je pozorně přečíst. Likvidace Základní bezpečnostní pokyny • Evropská směrnice 2012/19/EU o odpadu tvořeném elektrickými a elektronickými zařízeními nařizuje, že elektrospotřebiče nesmí být likvidovány v rámci běžného pevného městského odpadu.
Popis pračky CZ Ovládací panel Tlačítko a kontrolka START/PAUSE Tlačítko ON/OFF Tlačítko TEPLOTA DISPLEJ Dávkovač pracích prostředků Tlačítko OTOČNÝ OVLADAČ PROGRAMŮ PUSH&WASH+DRY Dávkovač pracích prostředků: slouží k dávkování pracích prostředků a přídavných prostředků (viz “Prací prostředky a prádlo”). Tlačítko ON/OFF : Zapněte nebo vypněte pračku krátkým stisknutím tlačítka. Kontrolka START/PAUSE pomalu blikající zeleným světlem poukazuje na to, že je zařízené zapnuté.
Displej CZ B A C D Displej slouží k naprogramování zařízení a poskytuje četné informace. V části A je zobrazována doba trvání různých programů, které jsou k dispozici, a po zahájení cyklu i zbývající doby do jeho ukončení; v případě nastavení ODLOŽENÝ START bude zobrazena doba chybějící do zahájení zvoleného programu.
Jak provést prací cyklus nebo cyklus sušení CZ Rychlé nastavení programu 1. NAPLŇTE PRAČKU PRÁDLEM. Otevřete dvířka s průzorem. Naplňte pračku prádlem a dbejte přitom, aby nedošlo k překročení množství náplně, uvedeného v tabulce programů na následující straně. 2. NADÁVKUJTE PRACÍ PROSTŘEDEK. Vytáhněte dávkovač pracích prostředků a naplňte prací prostředek do příslušných přihrádek způsobem vysvětleným v části “Prací prostředky a prádlo”. 3. ZAVŘETE DVÍŘKA. 4.
Programy a volitelné funkce Praní 4 3 3,5 3,5 1 2 3,5 - 90° 60° (Max. 90°) 60° 40° 20° 20° Doba trvání cyklu Programy Částečné Máchání/Bělicí prostředek Maximální náplň pro praní (Kg) Automatický 13 Praní&Sušení 45’ 14 AirFresh 600 800 1000 1000 0 800 800 Bělicí prostředek 9 10 11 12 Standardní programy pro bavlnu 60° (1): Silně znečištěné bílé a barevné prádlo z odolných tkanin. Syntetické: Velmi znečištěné barevné prádlo z odolných tkanin.
CZ Push&Wash+Dry Tato funkce umožňuje zahájit automatický cyklus praní a sušení i při vypnutém zařízení, aniž by bylo třeba nejdříve stisknout tlačítko ON/OFF, nebo následně při zapnutí zařízení bez použití jakéhokoli dalšího tlačítka a/nebo otočného ovladače (v opačném případě bude program Push&Wash+Dry zrušen). Za účelem zahájení cyklu Push&Wash+Dry držte stisknuté tlačítko po dobu 2 sekund. Rozsvícená kontrolka poukazuje na to, že cyklus byl zahájen.
Prací prostředky a prádlo Dávkovač pracích prostředků Dobrý výsledek praní závisí také na správném dávkování pracího prostředku: použití jeho nadměrného množství snižuje efektivitu praní a napomáhá tvorbě vodního kamene na vnitřních částech pračky a zvyšuje znečištění životního prostředí. ! Nepoužívejte prací prostředky určené pro ruční praní, protože způsobují tvorbu nadměrného množství pěny. ! Pro předpírku a praní při teplotě vyšší než 60 °C používejte práškové prací prostředky pro bílé bavlněné prádlo.
CZ Eco Syntetické 20° (program 12) ideální pro smíšené náplně (bavlna a syntetika), tvořené středně znečištěným prádlem. Dobrá výkonnost praní i za studena je zaručena mechanickým působením, které je založeno na změně rychlosti ve středních nebo určených intervalech. Praní&Sušení (program 13): byl navržen pro praní mírně znečištěného oblečení během krátké doby: Při volbě tohoto cyklu je možné vyprat a vysušit až do 1 kg prádla během pouhých 45 minut.
Poruchy a způsob jejich odstranění Může se stát, že pračka nebude fungovat. Dříve, než zatelefonujete na Servisní službu (viz “Servisní služba”), zkontrolujte, zda se nejedná o problém, který lze snadno vyřešit s pomocí následujícího seznamu. Poruchy: Možné příčiny / Způsob jejich odstranění: Pračku nelze zapnout. • Zástrčka není zasunuta v zásuvce nebo není zasunuta natolik, aby došlo ke spojení kontaktů. • V celém domě je vypnutý proud. Nedochází k zahájení pracího cyklu.
Servisní služba 195119461.01 02/2014 - Xerox Fabriano CZ Před přivoláním Servisní služby: • Zkontrolujte, zda nejste schopni poruchu odstranit sami (viz “Poruchy a způsob jejich odstranění”); • Znovu uveďte do chodu prací program, abyste ověřili, zda byla porucha odstraněna; • V záporném případě se obraťte na středisko servisní služby. ! Nikdy se neobracejte s žádostí o pomoc na techniky, kteří nejsou k výkonu této činnosti oprávněni. Při hlášení poruchy uveďte: • druh poruchy; • model zařízení (Mod.