Dishwasher Instruction for installation and use D 66
Safety Is a Good Habit to Get Into NOTICE Carefully read the instructions contained in this manual, as they provide important information which is essential to safe and proper installation, use and maintenance of the appliance. This appliance complies with the following EEC directives: - 73/23/EEC of 19/02/73 (Low Voltage) and subsequent modifications; - 89/336/EEC of 03/05/89 (Electromagnetic Compatibility) and subsequent modifications. 1.Carefully dispose of the packing material. 2.
Close-up View (Interior) E G F H J I K L Bottom Sprayer Arm Upper Rack Salt Container Cap Top Sprayer Arm Washing Filter Rack Height Adjustor Detergent and Rinse Aid Dispenser Lower Rack Technical characteristics Width cm. 60 Depth cm. 60 Height cm.
Salt ...... Salt The hardness of the water varies from place to place. If hard water is used in the dishwasher, deposits will form on the dishes and utensils. The appliance is equipped with a special softener that uses a salt specifically designed to eliminate lime and minerals from the water. Loading the Salt into the Softener Always use salt intended for use with dishwashers. The salt container is located beneath the lower rack and should be filled as follows: 1.
Detergent and Rinse Aid .... Detergent Detergent specifically intended for use with dishwashers must be used. The dispenser must be refilled before the start of each wash cycle following the instructions provided in the "Wash Cycle Table." The detergent dispenser is located on the inside panel of the door. Rinse Aid This product makes dishes sparkle and helps them to dry without spotting.
Loading the Dishwasher Lower Rack Before placing the dishes in the dishwasher, remove the larger food particles to prevent the filter from becoming clogged, which results in reduced performance. If the pots and pans have baked-on food that is extremely hard to remove, we recommend that they be allowed to soak before they are washed. This will eliminate the need for extra wash cycles. Pull out the racks to facilitate loading the dishwasher.
Turning on the Appliance Starting a wash cycle.... 1. Make sure that the plug for the appliance is inserted into the wall socket. 2. Make sure that the water supply is turned on to full pressure. 3. Load the dishwasher (see the section entitled, "Loading the Dishwasher"). 4. Pour in the detergent (see the section entitled, "Salt, Detergent and Rinse Aid"). 5.
Wash Cycle Table Cycle 1) Normal Wash 55°C 1) Normal Wash 2) Reduced Wash 55°C 3) Delicates 4) Rinses 5) Rapid Wash & Dry 6) Soak INTENSIVE 65°C Button Detergent for Pre-wash + Wash Rinse Aid 2 pre-washes with cold water. Extended wash at 55°C. Rinse with hot water at 65°C. Drying. 5+25 gr. * Very dirty dishes, pots and pans (not to be used with delicate items). Pre-wash with cold water. Pre-wash with hot water. Extended wash at 65°C. Rinse with cold water. Rinse with hot water at 65°C.
Energy Saving Tips - It is important to try and run the dishwasher when it is fully loaded in order to save on energy. In order to prevent odors from forming and food from caking onto the dishes, you can run the hold cycle. - Choose the right wash cycle: the choice of cycle depends on the type of dishware, cookware and utensils being washed and how dirty they are.
Cleaning and Special Maintenance The filter assembly If you want consistent good results from your dishwasher, you need to clean the filter assembly; this way the food particles are removed from the wash water, allowing it to be recirculated during the cycle, filtered perfectly. For this reason, it is a good idea to remove the larger food particles trapped inside the cup “C” and semi-circular filter “A” after each wash.
Installation Positioning the Appliance Position the appliance in the desired location. The back should rest against the wall behind it, and the sides, along the adjacent cabinets or wall. The dishwasher is equipped with water supply and drain hoses that can be positioned to the right or the left to facilitate proper installation. This dishwasher model can be built-in under the one worktop, and it therefore comes provided with an assembly kit complete with an instructions sheet.
Electrical Connection Electrical Connection If your appliance is supplied with a 13 amp. fused plug it can be plugged into a 13 amp socket for immediate use. Before using the appliance please read the instruction below. WARNING: THIS APPLIANCE MUST BE EARTHED. THE FOLLOWING OPERATIONS SHOULD BE CARRIED OUT BY A QUALIFIED ELECTRICIAN. Replacing the fuse: When replacing a faulty fuse, a 13 amp ASTA approved fuse to BS 1362 should always be used, and the fuse cover re-fitted.
Xerox Business Services - DocuTech Viale Aristide Merloni 47 60044 Fabriano Italy Tel +39 0732 6611 Fax +39 0732 662501 www.merloni.com 10/2001 - 195032427.
