User Manual

ManualsBrandsIn Tech Electronics ManualsAudio EquipmentBluetooth Headset

Index

BT 28VM

User Manual

Speaker

Ear hook

Lock

On Off S1/()

Volume Up (S2)

Volume Down S3()

LED

Microphone

Installation of battery

Turning on the Headset

Turning off the Headset

Thank you for buying new BT 28VM Headset.

Before use please open the battery door and install the battery (AAAx1) into the

battery compartment according to the correct polarity. Close the battery door.

While the Headset (HS) is powered down, press and hold S1 for approx 10 seconds

until you hear a low tone followed by a high tone. The orange LED will turn on for 1

second then flashes.

While the HS is powered up, press and hold S1 until you hear a high tone followed by

a low tone indicating that the HS is powered down. And the LED will keep on Red

until S1 is released.

Bluetooth

Answering Incoming Calls

Transferring Calls

Muting the microphone

Ending Calls

When an incoming call is present, the HS will ring . Pressing S1 will answer the call.

The orange LED will continue to flash quickly while the call is in session.

(For Nokia 3650 or equivalent models)

When you are in session, calls can be transferred from the phone to the HS

and from the HS to the phone.

To transfer a call to or from the phone: double press S1, the call will be

transferred to or from the phone, or follow the operating instructions of your

phone.

Pressing both S2 and S3 buttons simultaneously for about a second, the microphone

will be muted. A periodic beep tone will be heard while the mute function is active.

When the microphone is muted, press on both S2 and S3 buttons simultaneously will

end the mute function and the periodic beep tone will stop.

While a call is in session on the Headset, pressing S1 will disconnect the call. After the

call is disconnected, the orange LED will flash normally.

Bluetooth

To mute the microphone during an active call

To end the mute function

To make a new call using voice dialing

Redialing last dialed number

Rejecting incoming call

Adjusting Speaker Volume

1.Make sure the voice dialing function is probably set up in the Mobile phone and it is

within the range of the HS. Press S1 on the HS shortly.

2.After the beep tone on the HS, make a voice dialing as you normally would by

saying the name of the person on the HS. The call will be connected in a few

seconds.

1. Make sure the voice dialing function is probably set up in the mobile phone and it is

within the range of the HS. Press S1 on the HS shortly.

2. After the beep tone on the mobile phone, make a voice dial as you normally would

and the call will be connected in a few seconds.

(Support handsfree profile mobile only. For Nokia

3650, Siemens S55,

equivalent models)

To redial the last dialed number, press and hold S3 for 2 seconds, a short low tones

will indicate an attempt to redial.

(Support handsfree profile mobile only. For Nokia 3650,

Siemens S55, or equivalent models)

When there is an incoming call and you want to reject it, press the buttons S1 and hold

it until you hear a long beep tone, then release it.

While a call is in session pressing and releasing S2 will increase the speaker

volume; pressing and releasing S3 will decrease the speaker volume on the HS

There is a key tone to indicate volume increase or decrease However a

warning tone will be heard when the volume level reaches its maximum or

minimum

When using a Bluetooth mobile phone:

When using a mobile phone without Bluetooth built-in and requiring a Bluetooth dongle:

Putting Headset in Pairing Mode

Establishing Link

Make sure the HS is fully powered before pairing starts. While the HS is powered off,

press and hold S1 for 10 seconds. Red and Orange LED is flashing alternately

indicating that the HS is in Pairing Mode.

Follow the operating instructions for your mobile phone to start the pairing

process. Typically, this has to be done by going to a setup or connect menu and then

selecting the options to discover devices.

may

take several

seconds to establish

a connection.

Your phone s display should indicate that it has found the T 28VM headset and

asks if you want to pair it. You should confirm this. The phone s display would prompt

you for a passkey or PIN. Enter a sequence of 0000 .

The headset LED will flash Orange every 3 seconds, indicating successful pairing.

Usually the phone will also ask whether you want to change the headset s name. We

recommend you should approve the BT 28VM name and not change it. You can pair

as many headsets and devices as you wish in your mobile phone.

If pairing does not occur as expected. Turn the headset and phone off and wait for 10

seconds. Turn the headset and phone on again and repeat all steps from beginning.

After pairing, the mobile phone will show connect then please select YES to

establish the link Now you are ready to make and answer calls on the HS For other

phones please follow the operation manual to establish the link

Bluetooth

“”

“

”

“

”

Bluetooth

Headset pictures .............................................................................2

Installation of battery .......................................................................2

Turning on the Headset .......................................................................2

Turning off the Headset ......................................................................2

Putting Headset in Pairing Mode ..............................................................3

Establishing Bluetooth Link ..................................................................3

Answering incoming calls .....................................................................4

Transferring calls ............................................................................4

Muting the microphone ........................................................................4

Ending calls .................................................................................4

To make a new call using voice dialing .......................................................5

Redialing last dialed number .................................................................5

Rejecting incoming call ......................................................................5

Adjusting speaker volume .....................................................................5

Ear Hook orientation .........................................................................6

Bend the ear hook to fit your ear ............................................................6

Putting way .................................................................................7

Low-battery indication .......................................................................7

Voice Over Internet Protocol (VOIP) Application .............................................8

FCC Interference Statement ..................................................................9

Declaration of Conformity ..................................................................11

Bluetooth

Headset

Summary of content (2 pages)

PAGE 1
Bluetooth ® Headset BT 28VM Putting Headset in Pairing Mode Make sure the HS is fully powered before pairing starts. While the HS is powered off, press and hold S1 for 10 seconds. Red and Orange LED is flashing alternately indicating that the HS is in Pairing Mode. Follow the operating instructions for your Bluetooth mobile phone to start the pairing process. Typically, this has to be done by going to a setup or connect menu and then selecting the options to discover Bluetooth devices.
PAGE 2
Ear Hook orientation If you want to change the orientation of ear hook, please follow the following steps. Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.