NOTE: Please read all instructions carefully before using this product Table of Contents Safety Notice Hardware Pack IRON GRIP STRENGTH WEIGHT BENCH IGS-8858 Assembly Instruction Exploded Diagram Parts List Warranty Ordering Parts Model IGS 8858 Retain This Manual for Reference 07/25/06 OWNER'S MANUAL IMPEX® INC. 14777 Don Julian Rd., City of Industry, CA 91746 Tel: (800) 999-8899 Fax (626) 961-9966 www.impex-fitness.com info@impex-fitness.
TABLE OF CONTENTS BEFORE YOU BEGIN...................................................................................... IMPORTANT SAFETY NOTICE....................................................................... HARDWARE PACK………............................................................................... ASSEMBLY INSTRUCTIONS........................................................................... EXPLODED DIAGRAM....................................................................................
IMPORTANT SAFETY NOTICE PRECAUTIONS This exercise machine is built for optimum safety. However, certain precautions apply whenever you operate a piece of exercise equipment. Be sure to read the entire manual before you assemble or operate your machine. In particular, note the following safety precautions: 1. Keep children and pets away from the machine at all times. DO NOT leave children unattended in the same room with the machine. 2. Only one person at a time should use the machine. 3.
WARNING LABEL REPLACEMENT The Warning Label shown here has been placed on the Cross Brace. If the label is missing or illegible, please call customer service at 1-800-999-8899 for replacement.
HARDWARE PACK 4
HARDWARE PACK 5
ASSEMBLY INSTRUCTION Tools Required Assembling the Machine: Two Adjustable Wrenches and Allen Wrenches. NOTE: It is strongly recommended two or more people assembling this machine to avoid possible injury. STEP 1 (See Diagram 1) A.) Connect the Left & Right Upright Beam (# 1 & #2) by a Cross Brace (#4) in the mid span. Secure them with M10 x 3 ¾” Carriage Bolts (#40), one 5 ½” Bent Bracket (#16), two ∅ ¾” Washers (#49), and two M10 Aircraft Nuts (#52) on each side. B.
STEP 2 (See Diagram 2) A.) Attach the front of Main Seat Support (#3) to the Front Post (#9). Secure it with two M10 x 3 1/8” Carriage Bolts (#41), one 6 ¼” Bent Bracket (#18), two Ø ¾” Washers (#49), and two M10 Aircraft Nuts (#52). B.) Attach the Main Seat Support to the top of Front Post. Secure it with two M10 x 3 1/8” Carriage Bolts (#41), one 4 ¾” Bent Bracket (#17), two Ø ¾” Washers (#49), and two M10 Aircraft Nuts (#52). C.) Attach the Main Seat Support to the Cross Brace (#4).
STEP 3 (See Diagram 3) A.) Attach the Backrest Incline Support (#13) to the side-holes on the two Backrest Supports (#12). Align the holes. Secure it with one M12 x 7 ¼” Allen Bolt (#43), two Ø ¾” Washers (#49), and one M12 Aircraft Nut (#52). B.) Attach the holes on the end of the Backrest Supports (#12) to the pivot on the Main Seat Support (#3). Attach the two ends of the Seat Support (#11) to the two holes on end of Backrest Supports. Align the holes.
STEP 4 (See Diagram 4) A.) Attach the Backrest Board (#20) to the Backrest Supports (#12). Secure it with four M8 x 1 5/8” Allen Bolts (#45) and four Ø 5/8” Washers (#50). B.) Place the Seat (#21) onto the Seat Support (#11). Secure it with four M8 x 1 5/8” Allen Bolts (#45) and four Ø 5/8” Washers (#50). C.) Attach the Arm Curl Pad (#22) to the Arm Curl Bracket (#55). Secure it with two M8 x 5/8” Allen Bolts (#46) and two Ø 5/8” Washers (#50). D.
STEP 5 (See Diagram 5) A.) Attach the Leg Developer (#8) to the Main Seat Support. Secure it with an Axle (#26), two M10 x 5/8” Allen Bolts (#44), and two Ø ¾” Washers (#49). B.) Insert two Foam Tubes (#19) halfway through the holes on the Leg Developer. Push four Foam Rolls (#29) onto the Tubes from both ends. Plug four Foam Roll End Caps (#33) into the ends. C.) Slide an Olympic Sleeve (#30) onto the weight post on Leg Developer. Attach a Spring Clip (#25) onto the Sleeve. D.
11
PARTS LIST KEY NO.
IMPEX INC. LIMITED WARRANTY ® IMPEX Inc. ("IMPEX ") warrants this product to be free from defects in workmanship and material, under normal use and service conditions, for a period of two years on the Frame from the date of purchase. This warranty extends only to the original purchaser. IMPEX's obligation under this Warranty is limited to replacing or repairing, at IMPEX's option. All returns must be pre-authorized by IMPEX.