User's Manual

Pantone Cool Gray 11C、C:0 M:20 Y:100 K:0
7-10 ft
(2-3 m)
Up to 26 ft (8 m)
CONTENTS
English 01-14
00-00Deutsche
00-00Español
00-00Italiano
00-00Français
00-00Pусский
All products bearing this symbol are waste electrical
and electronic equipment (WEEE as in directive 2012/
19/EU) which should not be mixed with unsorted
household waste. Instead, you should protect human
health and the environment by handing over your waste equi
pment to a designated collection point for the recycling of
waste electrical and electronic equipment, appointed by the
government or local authorities. Correct disposal and recycling
will help prevent potential negative consequences to the
environment and human health. Please contact the installer
WEEE Information
Hereby, Shanghai Imilab Technology Co., Ltd. declares that
the radio equipment type IMILAB EC4 is in compliance with
Directive 2014/53/EU.
WEEE Information
FCC Statement
Changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to
operate the equipment. This device complies with Part 15 of
the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including
interference that may cause undesired operation.
Note: This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and
can radiate radio frequency energy, and if not installed and
used in accordance with the instructions, may cause harmful
interference to radio communications.
However, there is no guarantee that interference will not occur
in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or
more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for
help.
FCC 20cm Statement: This equipment complies with FCC
radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and
operated with a minimum distance of 20cm between the
radiator & your body. This transmitter must not be co-located
or operating in conjunction with any other antenna or
transmitter.
Method 1
Method 2
5V USB Charger
Charging the camera
SYNC
USB
Power
Reset
Ethernet
Specifications
Safety statement
Name: IMILAB EC4
Model: CMSXJ31A
Resolution: 2560x1440
Aperture: F1.6
Power Input: 5 V 2 A
Item Dimensions: 82 x 86.8 x 50 mm
Operating Temperature: -20 °C ~ 50 °C
FCC ID：2APA9-CMSXJ31A
EN-09
Mount the camera
The camera can be mounted both indoors and outdoors.
1. Drill two holes on the wall by using the base of the IMILAB
EC4 as a template. It is recommended that you mark the
locations of the hole with a pencil before drilling. The
diameter of each hole is approximately 6 mm, and the depth
is approximately 30mm.
2. Insert the anchors into the holes.
EN-04
Camera field
of view
Motion
Detection
Zone
Mounting the camera
Select height and location
1. Hang the camera 7-10 ft (2-3m) above the ground. This
height maximizes the detection range of the motion sensor
of the camera.
Product overview
Camera
Spotlight
Lens
Microphone
Status LED
Light sensor
Motion
sensor
Mounting hole
Speaker
SYNC Button
USB Charging Port
Setting up the system
Download the app and set up the system
1. Download the Imilab Home APP
from the app store (ios devices) or
google play (Android devices).
2. Sign up for a imilab home account , then follow the
onscreen instructions to complete the setup.
EN-02 EN-03
EN-11 EN-12
Manufacturer: Shanghai Imilab Technology Co., Ltd.
Address: Room 001A, Floor 11, Block 1, No. 588 Zixing Road,
Minhang District, Shanghai, China
For further information, please go to www.imilab.com.
Support: [e-mail]
WARNING
This product can expose you to
chemical Bisphenol A (BPA) which is
known to the state of California to cause
reproductive.
For more information, go
www.P65Wamings. ca. gov.
EN-08
4. Match the bottom groove of the camera mounting base
with the raised area on the base. Press down until the two
surfaces are flush, then turn it in either direction to lock it in
place.
5. Tighten the camera to the mounting bracket and adjust the
viewing angle by checking the live stream feed in the app.
Warning:
To avoid any damages or injuries, the device must be
securely fastened to the Ceiling/wall as specified in the
installation instructions.
When mounting the security camera on a wall:
Please note that the wall must be able to support at least
triple the product's total weight.
EN-05
Getting started
IMILAB EC4
Micro-USB
Charging Cable
Mounting
Bracket
Mounting Screws
and Anchors
For camera installation
EN-01
The suitable operationg temperature range for this product
is between -20℃~50℃. Don't use the product in an
environment with temperatures above or below the
specified range.
When charging, the operating tempreture range for this
product is between 0°C~ 45°C. Don't charge the product in
an environment with temperatures above or below the
specified range.
Using the product in a low tempreture environment or
charging status will affect its standby time. The actual
standby time is related to the user's environment and habbit.
To improve the product's performance, please do not place
the cameralens facing or next to a reflective surface, such as
glass windows/doors and white walls, which will cause the
image to appear overly bright inareas close to the camera
and darker in areas further away, or cause thecamera to
produce white images.
Please install the product in areas with Wi-Fi reception, and
try to place the device where the Wi-Fi signal is strong. In
addition, please keep the security camera away from metal
structures, microwave ovens, or other locations where signal
strength may be impacted.
Don't replace the battery in camera yourself—if not properly
replaced, there is a danger of explosion.
Precautions Battery (battery pack or batteries) must not be exposed to
sunlight, fire, or similar overheating conditions.
This product is a low power consumption camera with
battery built-in. Don't use Real-Time Monitoring feature for
long time when charging, in order to avoid battery life loss.
Do not use the device in the environment at too high or too
low temperature, never expose the device under strong
sunshine or too wet enviroment.
EN-07
EN-10
EN-13
EN-14
EN-06
IMILAB EC4
Spotlight Battery Camera
User Manual
Read this manual carefully before use,
and retain it for future reference.
EN DE ES FRIT RU
or local authorities for more information about the location
as well as terms and conditions of such collection points.
3. Firmly screw the base of the mounting bracket onto the wall.
开关机
听到开机音乐，开机成功
听到关机音乐，关机成功
长按SYNC Button 2秒，
至指示灯蓝色常亮
长按SYNC Button 15秒，
至指示灯红色闪烁
长按SYNC Button 8秒，
至指示灯蓝色闪烁，松开按键
使用USB充电线/太阳能板
充电，红色闪烁3次
绿色常亮
蓝色闪烁
蓝色常亮5秒后熄灭
蓝色和橙色交替闪烁3次
开始充电
充满电
开始重置
（重置过程中，摄像机会重新启动）
重置成功
配对成功
配对失败
摄像机充电
摄像机重置
摄像头Status LED Status Status
橙色闪烁1次 PIR侦测到有人
PIR持续侦测到有人橙色持续闪烁
PIR侦测
灵敏度调节