User Manual
COMMENT 一、 Product Introduction .................................................. 1 Product Profile ......................................................... 2 Product Features ........................................................ 2 Application Scenarios ................................................... 2 二、 Introduction to its Functions ......................................... 2 三、 Appearance Specifications ............................................. 3 Basic Parameters ............................
一、Product Introduction Product Profile iMGS-MVT04T21 is an led video controller produced by iMGS which has integrated with a video processor and sending card. It supports quick led display set-up, without using the computer software to configure the connections of the led display, which has greatly simplified the on site debugging steps.
It supports dual picture function, picture in picture or picture out picture could be realized, the size is adjustable. It supports the pixel to pixel scaling of the input image according to the resolution of the display. It supports multiple devices cascading connection. 2 x HDMI displays simultaneously It supports WIFI Control It supports user-defined EDID and management. It supports USB play. it supports timed lock.
Signal Standards:PAL/NTSC; CVBS 2 Supported Resolution:480i,576 Interface:USB2.0; Supported Resolution : Video 1080P downwards compatible with pictures 4096x2160 downwards USB 1 compatible Supported Formats:rm,rmvb,mp4, mov, m k v, w m v, a v i , 3 g p jpg,bmp,png Signal Standards:SD/HD/3G-SDI SDI 1 Supported Resolutions:1080p/I 720p/i 3.
Front Panel Specifications No. Buttons Specifications 1 LCD 2 Operation Button Displaying the Operation Menu Knob to choose the Menu ESC Button 3 Inputs Source Switching Buttons Input Source and Test Signal Dual Pictures Quick Switch Button Partial and Full Display Switching Button 4 Function Buttons Picture Capture Quick Switch Button Brightness LED Settings 5 Power On/Off Power ON/OFF Rear Panel Rear Panel Specifications No.
SDI:SDI Signal Input SDI-LOOP:SDI Signal Loop Out CV1、CV2:CVBS Signal Input DP:DP Signal Input HDMI1、HDMI2:HDMI Signal Input VGA:VGA Signal Input Gigabit Ethernet 3 4xLED Ethernet Ports Output Port RS232:Serial Connection Port 4 Control Port B Type USB:Debugging Port to connect to the PC 5 Antenna Interface To connect to the WIFI Antenna ;Mobile APP Control 四、Operating Instructions Main Interface After the processor is turned on, the LCD Display shows the following main interface: Shows Setting Time
The Menu Interface has 6 main Menu Options: Output,LED Display, Splicing,Functions,Preset, System. Output 1. 11 Specified Resolutions are set under the Conventional Resolution 2.
minimum frame rate is 30HZ and the maximum is 60HZ.(Select the option to be changed and press OK to change). 3. Horizontal Width: it refers to the width (resolution) it could be uploaded. 4. Vertical Height:it refers to the height(resolution) that it could be uploaded. 5. Horizontal Start: The Start Point default to 0, if that’s needed, customer is able to change the start point offset X Axis according to the requirements. 6.
1. Brightness: the display value is what the current screen brightness is, the maximum is 128 and the minimum is 0. 2. Identify the type of the receiving card: it could be detected that the current led display is of T6 Type or FPGA Type. 3. Check the QTY of the receiving Card: it could detect how many receiving cards are currently being used on the led display. 4. Simple Connection: As following Picture Shown (1) Arrangement: there are 3 ways of arrangement: horizontal,vertical and 2x2.
Splicing 1. Output Resolution: as it has already been introduced above, we won’t explain it here again. 2. Splicing Parameters Settings: As shown 1. Splicing Switch: Before Splicing, the splicing switch must be turned on. 2. Splicing Synchronization: Splicing Synchronization. 3. Total Horizontal Width: refers to the current value of the led display width. 4. Total Vertical Width: refers to the current height value of the led display. 5.
(it could avoid the small resolution deviation of the led display so that you may need to adjust the parameters again) 8. Reset: only with one key you could get back to the state when it has no parameters at all,and to reset the parameters. Functions 1.
To turn on the picture in picture function of the processor and set the starting point of the video source, the width and height parameters of the PIP so as to achieve the PIP on the same output. There is also a quick One-Key PIP on the device. (2) Keying Function Turn on the keying function of the processor, switch the input signal source to the current used signal source of the led display, and the color keys are : Red,Black,Blue and Green. 2.
Partial functions: the size of the displaying area of the led display could be set according to the users themselves, or it could be set as that the system automatically force to compress it into a full screen. There is also a quick one key to display partial or full screen. Input Settings EDID Management: Modify the EDID of Input Signal such as: HDMI and DVI, which including resolutions,refresh frequency parameters. (1) .Input: switch the input signal source (2) .
ADC Calibration; You can enable ADC calibration function of CV1、CV2、VGA、HDMI2 signals . Audio Management Volume: adjust the volume of the device from 0-100 3.
Timed Switching: you could switch to the preset parameters which have been saved beforehand, and you could save maximum 10 preset modes. Advanced Settings: A 4-digit password could be set as the device protection. 4. Fade in /Fade Out time 0-10 value, the larger the value is the slower switching response it will get. 5. Black Screen/ Freeze Button You can get the screen to be black or get it frozen with one button. 6.
Image Modes: Natural,Soft,Dynamic Color Temperature: Standards, Cool,and Warm Brightness:0-100, the brightness could be set according to the certain requirements. Contrast Ratio:it could be adjusted to your favorite image mode Hue Saturation: you can adjust the hue saturation to make the image color more intuitive. Gamma:You can adjust the value of the Gamma that the device hasn’t got in. Definition: it has 24 levels of the definition value, it could be adjusted according to the site requirements.
output to the LED screen is missing , Offset or other issue and then it requires a manual modification of the parameters. 8. WIFI Management Using the WIFI function then you can set the WIFI parameters and the IP Preset 10 preset parameters could be saved, and you can use them with just one key’s press.
Key Lock: The key lock can prevent the touch of the signal source button during use, which could causes signal source of the screen to be wrong. System Version Information: You can see whether the device version is the latest or not. Factory Reset: Restore Factory Settings This device complies with Part 15 of the FCC Rules.