ILD703G5, ILD604G4, ILD786G5, ILD906G5, ILD914G5
OPEN 24/7 ILVE ACCES SSORIES ONLINE E SHOP P -VY H ^PKL YHUNL VM JVɈLL THJOPULZ WVKZ HUK V[OLY 03=, HJJLZZVYPLZ H[ [OL JSPJR VM H I\[[VU ZOVW PS]L JVT H\
Dear customer, Congratulations on your purchase of a ILVE induction ceramic hob. In order to make the best use of your appliance, please carefully read the following use and care manual and keep it for later reference. SUMMARY SAFETY ......................................................................................................................................... 4 PRECAUTIONS BEFORE USING........................................................................................................
SAFETY Precautions before using • • • • • • • • • • • Unpack all the materials. The installation and connection of the appliance must be done by approved and qualified specialists. The manufacturer cannot be responsible for damage caused by installation or connection errors. When used, the appliance must be correctly installed in a kitchen unit and an adapted and approved work surface.
Precautions not to damage the appliance • • • • • • • • • • Raw pan bottoms or damaged saucepans (not enamelled cast iron pots) may damage ceramic glass. Sand or other abrasive materials may damage ceramic glass. Avoid dropping objects, even little ones, on the vitroceramic. Do not hit the edges of the glass with saucepans. Make sure that the ventilation of the appliance is in accordance with the manufacturer’s instructions. Do not put or leave empty saucepans on the vitroceramic hobs.
DESCRIPTION OF THE APPLIANCE Technical characteristics Dimension Nominal Power* 1st Booster Power* 2nd Booster Power* Minimal pan detection 7400 W Left Centre Right Ø260 mm 220x180 mm 220x180 mm 2600 W 2100 W 2100 W 3300 W 2600 W 2600 W 5500 W 3700 W 3700 W 120 mm 100 mm 100 mm 7400 W 4 zones 220x180 mm 2100 W 2600 W 3700 W 100 mm ILD906G5 11100 W ILD786G5 6 zones 220x180 mm 2100 W 2600 W 3700 W 100 mm Total Power Position of the heating zone ILD703G5 ILD914G5 ILD604G5 Type *
USE OF THE APPLIANCE Sensitive touch Your ceramic hob is equipped with electronic controls with sensitive touch keys. When your finger presses the key, the corresponding command is activated. This activation is validated by a control light, a letter or a number in the display and/or a “beep” sound. In the case of a general use press only one key at a time.
Power selection zone “SLIDER” and timer setting zone To select the power with the slider, slide your finger on the “SLIDER” zone. You can directly access if you put your finger directly on the chosen level.
Residual heat indication After the heating zone is turned off, or the complete stop of the hob, the heating zones are still hot and indicates [ H ] on the display. The symbol [ H ] disappears when the heating zones may be touched without danger. When the residual heat indicators are on, don’t touch the heating zones and don’t put any heat sensitive object on them. There are risks of burn and fire.
• To stop the cooking time: Action Control panel Display Select the Timer press simultaneously key [ - ] and [ + ] Timer display on from the timer until the desired display is on Stop the time press key [ - ] from the timer [ 000 ] If several timers are activated, repeat the process. • Egg timer function : Egg timer is an independent function. It stops as soon as a heating zone starts up. If the egg timer is on and the hob is switched off, the timer continues until time runs out.
Recall Function After switching off the hob [ ], it is possible to recall the last settings. • cooking stages of all cooking zones (Booster) • minutes and seconds of programmed cooking zone-related timers • Keep warm function The recall procedure is following: • Press the key [ ] • Then press key pause/recal before the light stops blinking. The previous settings are again active. « Keep warm » Function This function allows liquids to reach and maintain automatically a temperature of 42°C, 70°C or 94°C.
COOKING ADVICE Pan quality Accepted materials : steel, enamelled steel, cast iron, ferromagnetic stainless-steel, aluminium with ferromagnetic bottom. Not accepted materials : aluminium and stainless-steel without ferromagnetic bottom, copper, brass, glass, ceramic, porcelain. The manufacturers specify if their products are compatible induction. To check if pans are compatible : • Put a little water in a pan placed on an induction heating zone set at level [ 9 ].This water must heat in a few seconds.
Examples of cooking power setting (the values below are indicative) 1 to 2 Melting Reheating 2 to 3 Simmering Defrosting 3 to 4 Steam 4 to 5 Water 6 to 7 7 to 8 9 P and Sauces, butter, chocolate, gelatine Dishes prepared beforehand Rice, pudding, sugar syrup Dried vegetables, fish, frozen products Vegetables, fish, meat Steamed potatoes, soups, pasta, fresh vegetables Meat, lever, eggs, sausages Goulash, roulade, tripe Potatoes, fritters, wafers Steaks, omelettes, fried dishes Water scallops, steaks Boilin
One or all cooking zone cut-off : • • • • • The safety system has actioned. You forgot to cut-off the cooking zone for a long period of time. One or more sensitive keys are covered. The pan is empty and its bottom overheated. The hob also has an automatic reduction Booster level to avoid overheating Continuous ventilation after cutting off the hob : • • This is not a failure, the fan continuous to protect the electronic device. The fan cooling stops automatically.
INSTALLATION INSTRUCTIONS The installation comes under the exclusive responsibility of service. The installer must respect the legislation and the standards enforce in his home country. How to stick the gasket: The gasket supplied with the hob avoids all infiltration of liquids in the cabinet. Installation has to be done carefully, in conformity of the following drawing. Stick the gasket (2) two millimeters from the external edge of the glass, after removing the protection sheet (3).
ELECTRICAL CONNECTION • • • • • • • • The installation of this appliance and the connection to the electrical network should be entrusted only to an electrician following the normal regulations. Protection against the parts under tension must be ensured after the building-in. The information on connections necessary are on the stickers. Place them on the hob casing near the connection box.
CONNECTION OF THE HOB FOR ILD906G5 AND ILD786G5 Mains Connection Cable diameter 230V~ 50/60Hz 1 Phase + N 3 x 4 mm² 400V~ 50/60Hz 2 Phases + N 4 x 2.5 mm² 400V~ 50/60Hz 3 Phases + N 5 x 1.
Warranty Card Eurolinx Pty Limited A.B.N.
Warranty Card JVU[PU\LK PS]L JVT H\ 7YVVM VM 7\YJOHZL *\Z[VTLYZ T\Z[ YL[HPU WYVVM VM W\YJOHZL PU VYKLY [V IL LSPNPISL [V THRL H ^HYYHU[` JSHPT PU YLZWLJ[ VM HU 03=, WYVK\J[ *SHPTPUN \UKLY [OL >HYYHU[` *\Z[VTLYZ ^PSS ILHY [OL JVZ[ VM JSHPTPUN \UKLY [OPZ >HYYHU[` \USLZZ 03=, KL[LYTPULZ [OL L_WLUZLZ HYL YLHZVUHISL PU ^OPJO JHZL [OL J\Z[VTLY T\Z[ JSHPT [OVZL L_WLUZLZ I` WYV]PKPUN ^YP[[LU L]PKLUJL VM LHJO L_WLUZL [V 03=, H[ [OL HKKYLZZ VU [OL >HYYHU[` 9LNPZ[YH[PVU *HYK :[H[\[VY` 9PNO[Z H
18157/1 18157/0
