Copyright 2019 KOJ Electronic Co., Ltd. All Rights Reserved. MERLIN RECEIVER UNIT User Manual KOJ Electronic Co.
Copyright 2019 KOJ Electronic Co., Ltd. All Rights Reserved. Document properties Properties Content Project name MERLIN RECEIVER UNIT Project proposer Illumicare Group Limited Contact John Higo Document title User Manual Version number 1.0.0 Creation date 2020-2-16 Developers KOJ Electronic Co.
Copyright 2019 KOJ Electronic Co., Ltd. All Rights Reserved. Directory 1.Introduction......................................................................................................................................1 1.1.Document purpose............................................................................................................... 1 1.2.Document scope................................................................................................................... 1 1.3.Readers.........
Copyright 2019 KOJ Electronic Co., Ltd. All Rights Reserved. 1.Introduction 1.1.
Copyright 2019 KOJ Electronic Co., Ltd. All Rights Reserved. and also supports full on-off control of bound RX. APP Applications running in smartphones, specifically Tuya APP. RX devices that have been added to Wi-Fi same network can be controlled by Tuya APP,. Bind the third-party smart speakers, also empty through the voice pair Wi-Fi A wireless communication protocol and networking technology, which connects terminal devices through wireless routers to realize interconnection between devices.
Copyright 2019 KOJ Electronic Co., Ltd. All Rights Reserved. On the other hand, because the communication distance of the Wi-Fi is limited (the effective distance is only ten meters to tens of meters), Illumicare Group Limited hope that the HUB can make up for a certain lack, so it is required that the communication distance can be reached farther. Through investigation, the R & D team decided to use LoRa technology to replace the original no-negotiation stack 2.
Copyright 2019 KOJ Electronic Co., Ltd. All Rights Reserved. garden. The input end is connected with the low voltage power supply source, and the output end is connected with the lighting lamp or the electrical appliance. Input and output are reserved for a certain length of wire to facilitate installation. To control its turn on or off by APP or SLAVE. Support lower temperature (-30 degrees Celsius) and meet certain waterproof requirements.
Copyright 2019 KOJ Electronic Co., Ltd. All Rights Reserved. can use the data analysis and operation management functions provided by them. This system uses the third party graffiti intelligent platform. APP and RX equipment are connected to the platform for interconnection. A third-party intelligent speaker can be purchased to access the platform to voice control RX equipment. 2.2.Product architecture 2.3.
Copyright 2019 KOJ Electronic Co., Ltd. All Rights Reserved. 4.Product Function Description 4.1.Product mainstream 4.1.1.Initialization process 4.1.
Copyright 2019 KOJ Electronic Co., Ltd. All Rights Reserved. 4.2.Functional matrix Functional class NO Function APP class REQ1.1 Registered accounts REQ 1.2 Verification account REQ 1.3 View a list of RX devices HUB bind REQ 1.4 View the specified RX device status REQ 1.5 transmitting the specified RX device switch signal REQ 1.6 Setting the scene REQ 1.7 Automation REQ 2.1 Switching current area REQ 2.2 send RX open device signal REQ 2.3 Send off RX device signal REQ 2.
Copyright 2019 KOJ Electronic Co., Ltd. All Rights Reserved. 4.3.1.1.Registered accounts A user can register an account via a mail address or mobile phone number to manage his RX device 4.3.1.2.Verification account A user logs into his or her account to manage his or her RX device using a mail address or cell phone number. 4.3.1.3.View a list of RX devices HUB bind Users can view a list of all RX devices that have been bound HUB this account. 4.3.1.4.
Copyright 2019 KOJ Electronic Co., Ltd. All Rights Reserved. 4.3.2.SLAVE Class 4.3.2.1. Switching current area Click the ZONE button to replace the current controllable area with up to 8 areas. when switching to a AL area, indicates control of all areas. Assuming region 1, then the current region will be region 2, region 2, region 3, region 4, region 5, region 6, region AL( whole region). 4.3.2.2.
Copyright 2019 KOJ Electronic Co., Ltd. All Rights Reserved. state of the device is off. 4.3.4.HUB Class 4.3.4.1. Electrical equipment After the equipment is connected to the power supply, the power indicator light will be long and initialized. The indicator on the right is WiFi long if an account has been established the HUB device is connected, otherwise the indicator on the right is extinguished. 4.3.4.2.
Copyright 2019 KOJ Electronic Co., Ltd. All Rights Reserved. 4.3.5.2.To establish an association between SLAVE area and RX equipment The user must establish an association (i.e. binding) between the SLAVE area and the RX device to control the device through the SLAVE. Mainstream follows: A. Connect the RX device to input power supply, power supply lights long; B. A user switches SLAVE to a specified area; C.
Copyright 2019 KOJ Electronic Co., Ltd. All Rights Reserved. 5.Summary of product parameters 5.1.SLAVE remote control Power supply :2 AAA dry batteries, not less than 1.5 V DC Temperature requirements :-30°C to 40°C Waterproof Grade: IPX3 Communication distance: not less than 3000 feet without barrier 5.2.
Copyright 2019 KOJ Electronic Co., Ltd. All Rights Reserved. 6.1.2.RX equipment dimensions Name Size RX 81*62*32mm 6.1.3.HUB equipment dimensions Name Size HUB 129*120*28mm 6.2.Packing size 6.2.1.SLAVE Remote control package size Size SLAVE Remote control packaging 140*20*10mm Name 6.2.2.RX Equipment Packing Size Name Size RX packaging 170*90*110mm 6.2.3.
FCC Compliance Notice This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
