Carefully read this manual before use in order to keep these products at full capacity.
Concerning the Instruction manual (Application) This manual explains how to configure the following cameras through Network from PC. ●IPD-BX11(Box-type IP Network Camera) without Audio, SD card slot, and DI/DO functions. ●IPD-DM11(Dome-type IP Network Camera) with Audio, SD card slot, and DI/DO functions. ●IPD-VR11(Vandal Resistant Dome-type IP Network Camera)with Audio, SD card slot, and DI/DO functions. This manual can be downloaded from the following URL: http://www.ikegami.co.
INDEX INDEX 1. Camera Login and Login Screen ............................................................................................... 1 2.Quick Configuration .................................................................................................................... 4 2-1.Step 1:Server Name.............................................................................................................. 4 2-2.Step 2:Local Date & Time Configuration.................................................
INDEX 6.Device Configuration................................................................................................................. 26 6-1.Serial Ports ......................................................................................................................... 26 6-2.Privacy Zone........................................................................................................................ 26 6-2-1.Add Privacy Zone ..............................................................
INDEX 8.Recording Configuration ........................................................................................................... 49 8-1.SD Configuration ................................................................................................................ 49 8-2.Recording Configuration .................................................................................................... 52 8-2-1.Camera .......................................................................................
Camera Login and Login 1.1. Camera Login and Login Screen Screen ① ② ③ ①Start Internet Explorer（IE）,input the URL of network camera as below. Then click the Go button. ●The initial setting of the camera is http://192.168.1.100/ . ②Input the Login Name(User Name) and Password of administrator. ●The initial setting are Login Name(User Name) "root" and Password "root". ③After input Login Name(User Name) and Password, press OK button. Once logged in, the Password can be changed to new one.
Configuration (Set up) Screen Structure The following table shows Configuration (Setup) menu structure hierarchy for IPD-DM11 and IPD-VR11 which have additional menu than IPD-BX11. Main Menu Setup Menu Sub-Menu 1 Sub-Menu2 Live Viewer なし なし なし n/a n/a n/a n/a n/a n/a Step 1 Step 2 Quick configuration Step 3 Step 4 Step 5 (IPD-DM11,IPD-V11) Finish Server Name System Configuration Date & Time Admin.
Main Menu Setup Menu Sub-Menu 1 Sub-Menu2 Motion Detection Primary Stream Secondary Stream DI/DO DI Status / DO Control n/a n/a n/a n/a E-mail FTP(Buffered) Advanced Configuration Advanced Services FTP(Periodic) Sensor Notification Alarm Output SD Status & Format SD Configuration SD Information Recording Built-in Module 0 Configuration Recording Recording Profile Configuration Recording Mode SD Status Report Clear Recording Camera 1 Camera 2 Camera 1 Camera 2 Camera 1 Camera 2 Input 1 In
2. Quick Configuration 2.Quick Configuration Quick Configuration Menu is to help the configuration for camera easily. Set up Menu Step5 is only display for IPD-DM11 and IPD-VR11. IPD-BX11 IPD-DM11, IPD-VR11 2-1.Step 1:Server Name Click Step 1, the Setup Menu for 4-1.Server Name is displayed. 2-2.Step 2:Local Date & Time Configuration Click Step 2, the Setup Menu for 4-2.Date & Time is displayed. 2-3.Step 3:Network Configuration : Static IP Click Step 3, the Setup Menu for 5-1-1.Static IP is displayed.
3. Live 3.Live Viewer Viewer This Live Viewer enable to control the video and audio of IPDBX11, IPD-DM11, and IPD-VR11 over the TCP/IP network on IE. It works with cameras to display streaming live video and to record the snap shot and/or AVI for streaming video on PC. When the Micro SD card (SD card) is inserted into SD card slot of IPD-DM11 and /or IPD-VR11, it is able to record and replay to/from SD card by Live Viewer. (IPD-BX 11 has no SD card slot) 3-1.
3-2.Live Viewer Screen The ActiveX installed PC can display the Live Viewer screen by login the camera and click the Live Viewer on the Configuration Menu on Live Viewer. Also the Icons and buttons on screen are able to operate as explained below. 3-3.Video and Audio Control 3-3-1.
If below popup alert window is displayed by click the Connect button, refer the 6-3-1.Camera & Motion and click the Enable radio button of Audio line. 3-3-2.Mouseover buttons When mouseover the live video screen, control buttons displayed on left -up of live video screen as below. These control buttons displaying is different between IPD-BX11(w/o SD card slot)and IPD-DM11/IPD-VR11 (with SD card slot). If Each button is mouseovered, the function of each button is shown on screen as below-right screen(e.g.
2)AVI button It can be captured for currently displayed live video and saved it as video AVI format in PC. Select live video to save and click AVI button for saving start, and click again for saving stop. Then saving screen is displayed, enter the folder also file name, and click the Save button. Note: When you play back the saved video from H.264 format live video, it is needed the proper CODEC.
Set the beginning of video file data. Instant playback will scan 1minute after set time Set the playback speed. Start searching data Play Reverse playback 1frame playback every click 1frame reverse playback every click Pause Stop 3-3-3.Mouse Right button click Menu When the right button of Mouse is clicked on the Live Viewer window, below pop-up menu will be displayed as extended menu. 1) Pause Click Pause button to stop and resume live view video. 2)FPS(Frame/Sec) Not supported.
3)Flip Click this button to invert the direction of video image, if select Mirror then original image invert horizontally as mirror, and select Flip then original image flipped vertically. 4)Mute Audio(Only for IPD-DM11, IPD-VR11 ) Click this button to make on and off Mute the Audio. Also please refer 3-3-1. Video Display and Audio control.
4. System Configuration 4.System Configuration Click System Configuration item, the below setup menu is displayed. It can be setup for camera system. 4-1.Server Name Click Server Name item, below Server Name Setup screen is displayed (Same as Quick Configuration Step1). It can be changed the name on Server name field, but other item name/values are not allowed to change. Enter the new server name in the Server Name field which can be used up to 21 alphanumeric or up to 10 Unicode characters.
4-2.Date & Time Click Time & Date item ,below Local Date & Time Configuration screen is displayed(Same as 2-2.Step 2:Local Date & Time Configuration). Date(yyyy/mm/dd) Set the date Time(hh:mm:ss) Set the Local time Time Zone Select and set the Time Zone for this system location.
4-3.Admin. Password Click Admin Password, then Administrator Password can be changed on below displayed screen. Administrator’s ID "root" fixed , not allowed to change Old Password Enter current password (Factory default "root"） New Password Enter new password between 4 and 23 alphanumeric .This password is Confirm Password also used for Login on IE and Authentication of RTSP streaming. After set the new password, click the Apply button to save and take into effect it.
4-5.User Registration(Limited Access) Displayed on Menu, but function is not implemented Click User Registration item, below User Registration setting menu screen is displayed. It is able to setup for Limited access User(add, edit, delete) through RTSP streaming. 4-5-1.Add Click Add radio button, the below screen is displayed. User ID Password Confirm Password Name Enter up to 23 alphanumeric characters Enter same password between 4 and 23 alphanumeric.
VS Module ID Camera No Built-in Module0 is set (fixed). Select Access stream between Camera No.1:Primary Stream, Camera No.2 :Secondary Stream and All: Both Stream. Alarm Control Set the permission to access for control Alarm system part. PTZ Control Set the permission to access for PTZ control(Not supported) Audio Control Set the permission to access for Audio control(Only IPD-DM11/VR11) Playback Set the permission to access for Playback control of recorded video.
4-5-2.Edit Click Edit radio button, the below screen is displayed. It is able to change the User Name for RTSP streaming, Password, User ID(Access name). This registered User ID can not be changed on this screen. If it is needed to change registered User ID, follow 4-5-3.Delete and next 4-5-1.Add procedure. User ID Password Confirm Password Name Select the registered User ID for editing on this filed. Enter same password between 4 and 23 alphanumeric.
5. Network Configuration 5.Network Configuration Click Network Configuration item of Configuration Menu, then below configuration screen is displayed. It is able to setup the Network conditions. Before this setup, it should be confirmed with Network Administrator of property. 5-1.Network Configuration Click Network Configuration of Setup Menu, then below 2-3.Step 3:Network Configuration : Static IP screen is displayed. 5-1-1.Static IP Click Static IP radio button, the below screen is displayed.
5-1-2.DHCP Client When it is needed to get automatically IP address from exist DHCP server in the network, click the DHCP Client radio button, and click the Apply button. Note: Above Network Status Notify function is not supported. But it is only explained on 5-5.Network Status Notification. 5-1-3.PPPoE This function is not supported PPPoE is used to connect IP camera to PPPoE Modem provided ISP. It is needed the verification ,ID and Password. After setup, click Apply button to save settings.
5-2.Network Ports Click Network Ports, then below setup screen is displayed. This setting is for HTTP port number which is used to connect Client PC and IP camera(Web page). It can be assigned between 80 and 6553 and default value is 80. After setup, click Apply button to save settings. Note: If the HTTP port number is changed than default 80, the connected URL should be attached new Port number as below example http:// [IP Address of camera] : [HTTP PORT NUMBER] / Camera Address [192.168.1.
5-4.View Network Status Click View Network Status item, below Network Status view screen is displayed. This view screen shows the network status information at present. When click the Refresh button, the status data will be set as newest data. If click Back button, new setting data will be cancelled and the screen will be back to previous screen display.
5-5.Network Status Notification This function is not supported Click Network Status Notification item, below menu and screen is displayed. If any changes happen for network status, it is sent the update network status information to registered email address. This function will work under DHCP or PPPoE. After finished above setting, click Apply button to save settings. The working conditions of this function are as follows ○5-6.IP-CCTV DNS Setup has been done. ○5-1-2.
5-6.IP-CCTV DNS Setup This function is not supported Click IP- CCTV DNS item on the Menu, below Setup screen is displayed. IP-CCTV DNS service provides a static & public domain name to help users' access IP camera even through their IP address is changed or they are used in local network. To use IP-CCTV DNS, users have to create ID from IP-CCTV DNS server（http://www.ipcctvdns.com）,and register the camera with MAC address and Product Key.
5-7.Port Forwarding & UpnP This function is not supported Click Port Forwarding & UPnP item on the Menu, below setup screen is displayed. Port Forwarding is to assign a certain network port to a network product, which users can access from outside of Local area network. It can be configured from router. There are 3 options in Port Forwarding UPnP. ○Manual:User Assigned Port To use when users can access network router(hub) and manually assign available network port to camera.
5-8.RTP/RTSP Click RTP/RTSP item on the Menu, below setup screen is displayed. The RTP/RTSP for camera video streaming and audio streaming(only IPD-DM11,IPD-VR11) are able to set on this screen. Enable:Start RTSP service Service Disable:Stop RTSP service To use ONVIF protocol, RTP/RTSP must be set Enable Recommended default number 554. If it is needed to change port number, RTSP Port enter the number as below. e.g.）port number 445 rtsp://192.168.
The video streaming for camera can be set as below example. This example is explained based on camera default IP address 192.168.1.100. Unicast Address Primary Stream rtsp://192.168.1.100/stream1 Secondary Stream rtsp://192.168.1.100/stream2 Multicast Address Primary Stream rtsp://192.168.100/multicast_stream1 Secondary Stream rtsp://192.168.100/multicast_stream2 5-9.SNMP Click SNMP item on the Menu, below setup screen is displayed.
6. Device Configuration 6.Device Configuration Click Device Configuration item on Menu, below setup screen is displayed. It can be setup privacy zone, camera, motion detection, Sensor Input, Alarm Output etc. 6-1.Serial Ports Displayed on Menu, but function is not implemented 6-2.Privacy Zone Click Privacy Zone item on Menu, blow setup screen is displayed. It can be set privacy zone if certain part of screen needs to unmonitored. 6-2-1.
6-2-2.Delete Privacy Zone Click the box(zone) which is needed to delete, then green-colored box is changed red-colored. Click Delete button, and red-colored-box is changed gray-colored box. Click Apply button, then it is deleted. 6-2-2.Delete Privacy Zone It can be defined 8 privacy zones maximum. If it is tried to set over 8 zones, above message is pop up on screen. 6-3.
6-3-1.Camera & Motion Click Camera & Motion on Menu, below configuration for camera menu is displayed .
6-3-2.Camera Control Click Camera Control item on the Menu, the below camera control button is displayed with camera streaming live video window. Click the Menu Enter button on camera control, then SETUP MENU for camera is displayed on live video window. It is able to setup DAY/NIGHT AGC ,AWB and etc., for camera with operating Up・Down・Left・Right and Enter buttons. The details of this camera setup is shown on INSTRUCTION MANUAL (BASIC)which is attached in camera package.
6-3-3.Motion Detection Click Motion Detection item on Menu, below setup screen is displayed. This Motion Detection function is worked on only Primary Stream of camera.. It can be defined the motion detection area from 12 x 12 divided areas of screen as above by clicking each divided area. Motion Enable:Effect motion detection function. Detection Disable:Stop motion detection function. Check All Effect all area for motion detection with one click this button.
6-3-4.PrimaryStream と SecondaryStream Click either Primary Stream or Secondary Stream item on Menu, below setup screen is displayed. H.264(VBR Mode) H.264(CBR Mode) M-JPEG Factory default setting is H.264 for Primary Stream, M-JPEG for Secondary Stream. Camera Print in Camera name Name Enter up to 21 alphanumeric characters or up to 10 Unicode. H.264 VBR(Variable Bit Rate)Mode Rate Control Mode Video is encoded with selected image quality and GOP. Bit rate is different each encoded video frame. H.
6-4.DI (Sensor Input) / DO (Alarm Output) Click DI/DO item on Menu, below Setup screen is displayed. It can be set Sensor input and Alarm Output. Sensor Print in Sensor name Input Name Enter up to 31 alphanumeric characters or up to 15 Unicode. Alarm Print in Alarm name Output Name Enter up to 31 alphanumeric characters or up to 15 Unicode. Select Normal Open: Sensor Normal is OPEN, and goes Closed when triggered by an event.
6-5. DI(Sensor Input ) Status / DO(Alarm Output ) Control Click DI Status/DO Control item on Menu, below. ○DO(Alarm Output ) Control It can simulate the Alarm output as triggered by event. When click the On button and the relay output is closed, click Off button and the relay output is opened. ○DI(Sensor Input ) Status It can confirm the Input Status from Sensor. Through above DO Control click On or Off button, then if the Check mark is on Check(On) field, it means DI/DO is worked completely.
7.Advanced Configuration 7.Advanced Configuration In Advanced Configuration menu, it can be set the service of E-mail, FTP, Sensor Notification, Alarm Output. Click Advanced Configuration item on Menu, below sub menu is displayed 7-1.Advanced Services Pre-Alarm buffer size and buffering speed can be defined here. Click Advance Services on Menu, the below setup screen is displayed. Pre-Alarm Buffer Size Set the buffer size of Pre-Alarm which is storing image before event in unit frame.
7-2.E-mail E-mail configuration is set up here for Alarm in case any event occurs. 7-2-1.E-mail（E-mail Service Configuration） Click E-mail item, below setup screen is displayed. This function is worked in M-JPEG compression mode for image. Click here, 7-2-2.Camera（E-mail Service Setup for Each Channel） Camera1,Camera2 setup screen on next page is displayed also. (Camera1:Primary Stream, Camera2:Secondary Stream) Service Enable:To use this E-mail service Disable:Not to use this E-mail service.
7-2-2.Camera（E-mail Service Setup for Each Channel） Click Camera 1 or Camera 2 item on Menu, below setup screen is displayed. For each camera, the following Condition1-3, Post-Alarm Buffer Size and Speed, text message and display style can be setup/Configured. Condition1 Select the Condition for Email service to be activated. Click here, ～Condition3 then 7-2-3.Condition setup screen is displayed. Pre-Alarm Buffer Size The Buffer size assigned for Pre-Alarm.
7-2-3.Condition Click the Condition 1～3 on the Menu, below setup screen is displayed. The setup procedure of Event and Schedule shall be referred 8-2-2. Condition 1. Service This shows what service is for this condition. Module ID Module ID for current setup (Fixed 0) Camera ID Camera ID for current setup. Enable / Disable Always Schedule Only Event Only Schedule & Event Enable:To use this condition Disable:Not to use this condition This condition applies all the time.
7-3.FTP(Buffered) It is able to setup the FTP(Buffered) parameter at Event occurred. 7-3-1.FTP(Buffered) Click FTP(Buffered) item on Menu, below setup screen is displayed. This function is worked in M-JPEG Camera1, Camera2 Service Server Address Base Directory Name Setup screen for 7-3-2.Camera(FTP Service Configuration) is displayed. （Camera1:Primary Stream, Camera2:Secondary Stream） Enable:To use FTP(Buffered)service Disable:Not to use FTP(Buffered ) service Enter FPT Server Address.
Server Name, Directory Name box checked:New directory is created for each Option Weekday, Month, Day item. Hour, Minute, Sec File Name box checked:New file is created for each Option. Sequence File Name box checked:New file is created starting from 0, with increment of 1 Directory Name box checked:New directory name is created with camera Camera Number number. File Name box checked:New file is created with camera number.
7-3-3.Condition Click Condition 1～3 on Menu, below setup screen is displayed. The setup procedure of Event and Schedule details shall be referred8-2-2. Condition 1. Service This shows what service is for this condition. Module ID Module ID for current setup (Fixed 0) Camera ID Camera ID for current setup. Enable / Disable Always Schedule Only Event Only Schedule & Event Enable:To use this condition Disable:Not to use this condition This condition applies all the time.
7-4.FTP(Periodic) It is able to setup the FTP(Periodic) parameter at Event occurred. 7-4-1.FTP(Periodic) Click FTP(Periodic) item on Menu, below setup screen is displayed. This function is worked in M-JPEG compression mode for image only. Camera1-Camera2 Service Server Address Setup screen for 7-4-2.Camera （ FTP Service Configuration ） is displayed.(Camera1:Primary Stream, Camera2:Secondary Stream) Enable:To use FTP(Periodic) service Disable:Not to use FTP(Periodic) service Enter FPT Server Address.
Connection Mode Overwrite Select connection mode for FTP server either Active or Passive. File Name box checked:New file overwrites on existing file with same file name. Server Name, Directory Name box checked:New directory is created for each Option Weekday, Month, Day item. Hour, Minute, Sec File Name box checked:New file is created for each Option. Sequence File Name box checked:New file is created starting from 0, with increment of 1.
7-4-3.Condition Click Condition 1～3 on Menu, below setup screen is displayed. The setup procedure of Event and Schedule details shall be referred 8-2-2. Condition 1. Service This shows what service is for this condition. Module ID Module ID for current setup. (Fixed 0) Camera ID Camera ID for current setup. Enable / Disable Always Schedule Only Event Only Schedule & Event Enable:To use this condition Disable:Not to use this condition This condition applies all the time.
7-5.Sensor Notification It is possible to setup the Sensor Notification parameters. 7-5-1.Sensor Notification Click Sensor Notification item on Menu, below setup screen is displayed. Input 1, Input 2 Service Setup screen for 7-5-2.Input is dispalyed. Enable:To use Sensor Notification service Disable:Not to use Sensor Notification service Service Mode Select network mode for CGI Main IP address Enter IP address to use in CGI or other functions.
7-5-2.Input Click Input1, Input2 on Menu, below screen is displayed. Condition1～ Condition3 CGI Name or Alarm Port Message Link to setup screen of 7-5-3.Condition is dispalyed. It is able to setup for Input of Sensor Notification service condition. Enter the contents of CGI or Alarm Port Message when it is used. After finished above setting, click Save button to apply the setting data. If click Back button, new setting data will be cancelled and the screen will be back to previous screen display.
7-5-3.Condition Click Condition 1～3 on Menu, below setup screen is displayed. The setup procedure of Event and Schedule details shall be referred 8-2-2. Condition 1. Service This shows what service is for this condition. Module ID Module ID for current setup (Fixed 0) Camera ID Camera ID for current setup. Enable / Disable Always Schedule Only Event Only Schedule & Event Enable:To use this condition. Disable:Not to use this condition. This condition applies all the time.
7-6.Alarm Output It is able to setup the Alarm Output Service. 7-6-1.Alarm Output Click Alarm Output item on Menu, below setup screen is displayed. Output 1 Service Link to setup screen of 7-6-2.Output. Enable：To use Alarm Output Service Disable：Not to use Alarm Output Service After finished above setting, click Save button to apply the setting data. If click Back button, new setting data will be cancelled and the screen will be back to previous screen display. 7-6-2.
7-6-3.Condition Click Condition 1～3 on Menu, below setup screen is displayed. The setup procedure of Event and Schedule details shall be referred 8-2-2. Condition 1. Service This shows what service is for this condition. Module ID Module ID for current setup (Fixed 0) Camera ID Camera ID for current setup. Enable / Disable Always Schedule Only Event Only Schedule & Event Enable:To use this condition Disable:Not to use this condition This condition applies all the time.
8.Recording Configuration 8.Recording Configuration IPD-DM11, IPD-VR11 have the slot for Micro SD card (SD card),which is supported 1GB to 32Gb. If the SD card is in slot, it can be recorded the Video and Audio of camera IPD-DM11, IPD-VR11. Click Recording Configuration item on Menu, the below screen is displayed. SD Configuration The SD card information is shown on Screen. To do Formatting and initializing the SD card in the camera SD slot.
After inserted the SD card, turn on the power of camera, login the camera with IE. Click SD Information item on Menu, below screen is displayed. If entire SD information is shown as -None- , it means the SD card is not formatted. In that case, click Back button and click SD Status & Format item on followed screen displayed. Now the below screen is displayed which is showing the list of available SD card. Unformatted:The SD card is not formatted. Formatted :The SD card is formatted.
Then below widow is displayed. Click Partition and Format button, pop up window to confirm the formatting. Click OK button then the formatting is proceed, and it is shown blow SD Format Status screen, Check Bad Block of Format Option is able to check the damaged bad block of SD card. If select this option, the formatting time may be several hours depend on the size of SD card. Note: If the formatting program is terminated during the format process by causing Power is stopped e.g.
SD Status & Format screen is displayed, it is able to show the 1st SD is formatted. After confirm this Formatted status, click the Reboot button to restart the camera. This rebooting takes 1 to 2minutes. After rebooted the camera, login the camera with IE. And click SD Information item on Menu, it is able to show the SD card formatted result on displayed screen as below. (The below screen shows SD card 2GB e.g.) 8-2.
8-2-1.Camera Click Camera1, Camera2 item on Menu, below setup screen is displayed. Condition 1~4 Set up screen is displayed as 8-2-2. Condition 1. Recording condition Graphic displays recording condition (Always, Schedule, Schedule & tablefor 24hours weekly Event) on table of time and days of week. Recording Service Server Module ID Camera Number Camera Name Pre-Alarm Images Pre-Alarm Speed Post-Alarm Images Post-Recording Speed Enable:To use this record function.
Follow the above screen and set up the recoding speed, camera name Pre-Alarm and Post Alarm images . After set up them properly, click Save button to save settings. Pre-Alarm and Post Alarm images are recommended M-JPEG. If it is selected H.264, only I frame is recorded. Each Camera1, Camera2 can be set different Condition 1～4 . All the conditions are checked and worked by OR logic, so it will start recording when at least one of the conditions it meets. 8-2-2.
Service This shows what service is for this condition. Module ID Module ID for current setup. (Fixed 0) Camera ID Camera ID for current setup. Enable / Disable Always Select Mode Schedule Only Event Only Schedule and Event Week Schedule Time Date Enable:To use this condition Disable:Not to use this condition Recording is enabled all the time. It is not able to set Schedule and Event .mode. Recording is done by setup schedule. Recording is controlled by Event setting condition. (e.g.
Below is explanation for setup done screens e.g. ○Condition1:The recording is done by every Saturday and Sunday of week. And it is controlled Schedule setup contents and Event occurred. ○Time(hh:mm):In this case, not setup it, this means all day 24hours scheduled. ○Week（Days）):In this case, not setup it, this means all week scheduled. ○Date（mm/dd）In this case, not setup it, this means all months scheduled. ○When it is clicked Save button, then below Recording Configuration Screen is displayed.
After finished above setting, click Save button to apply the setting data and below screen is displayed. If click Back button, new setting data will be cancelled and the screen will be back to previous screen display The recording status is shown on Status field of above screen. If the video is already being recorded, the Status is displaying Recording as above.
8-2-3.Pre-Alarm & Post-Alarm Configuration Example Setup e.g. 1) Condition1:Select Mode is set either Always or Schedule Pre-Alarm Images 5 Post-Alarm Images 5 Pre- Alarm Speed 1 fps Post- Alarm Speed 10fps Under this mode, Pre-Alarm Speed is effected, then the recording speed is 1fps. Other setting values for Items are not affected. Setup e.g.
8-3.Recording Profile Click Recording Profile item on Menu, blow screen is displayed. It can be confirmed and checked the setting for record condition of camera. 8-4.Recording Mode Click Recording Mode item on Menu, below screen is displayed. It can be selected the action either Circulation or Pause at full in case of the SD card capacity is full by recorded video data during the recording. ○Circulation:To overwrite the new recording data on oldest record data.
8-5.SD Status Report Click SD Status Report item on Menu, below screen is displayed. It can be sent the capacity information of SD card by E-mail, through this setting. It is useful in case of selected Pause at full of setting 8-4.Recording Mode. Disk Full Notification Periodic Notification Select Enable to use this function. Select Enable if it is needed to receive the SD capacity information on selected Day of week and Time. Day & Time Set the Day of week and Time to receive the Notification by email.
8-6.Clear Recording Config Click Clear Recording Config item on Menu, below window is displayed. Click Clear button on above window. Then pop-up confirmation window is displayed, click OK button to clear all Recording Configuration data in camera. This function is useful to clear the configuration for multiple cameras at once. 8-7.Delete Recorded Data Click Delete Recorded Data item on Menu, below window displayed. It can be deleted all stored video data by this function.
9. Utilities 9.Utilities This function has useful common setting Items and checking Items. System Log, Save Configuration, Reboot, Factory, Default, System, Update Also it has Player on Utilities menu (only shown when SD card is inserted to SD slot of IPD-DM11&IPD-VR11) can playback recorded video files in SD card and backup it. Please refer INSTRUCTION MANUAL(PLAYER INSTRUCTION) as separate volume. W/O Player Menu With Player Menu 9-1.
9-2.Save Configuration Click Save Configuration on Menu, below widow is displayed. (Not used this function) Seme as 2-6.Finish:Save Configuration The Configuration data(setup data) for IPD-BX11 / IPD-DM11 / IPD-VR11 camera is saved by each configuration(setup) step with Save button, thus this function is not used for these cameras. If click Back button, the window screen will be back to previous screen display. 9-3.Reboot Click Reboot item on Menu, below widow is displayed.
9-4.Factory Default Click Factory Default item on Menu, below window is displayed. All configuration(setup)data is restored with factory default data except IP address of camera. Click Factory Default button on above window. Next click OK button on pop-up window for confirmation. Then camera configuration(setup) data is back to factory default except IP address. If it is clicked Cancel button, the window will be back to previous screen display. 9-5.
9-5-1.All(Firmware, RAM disk, System, Web) Update 【Step 1】 Click the Start button on the line of All(Firmware, RAM disk, System, Web) Update. And the confirmation pop-up window is displayed. Click OK button on it, then start the update work by followed screen display. If click Cancel button, the window will be back to previous screen display. 【Step 2】 Firmware Upload Click Browse button, it can be found and selected the firmware image file "a_ker_ds" in PC.
It can be checked file name and size of selected Update firmware image file. After checked the file, click Next button then this file "a_ker_ds" is uploaded in camera and proceeded next step. If click Previous button, this screen is backed Step 2 screen If it is needed to stop the Update procedure, click Cancel button. The camera is rebooted automatically with previous firmware. The below Step4, Step5 and Step6 proceeding follow same step as Step2 and Step3 above.
【Step 7】 Upload finished After all ("Firmware", "RAM disk", "System", "Web")Upload(included Skip proceed) is finished, above confirmation screen is displayed. When this all Upload proceeding is all right, click Next button to execute the Update processing which is shown next displayed window. If this all Upload proceeding has is not all right, click Factory Default button to back the Update file version which had been done by Factory. It will back Factory default except IP address.
9-5-2.System and Web Update This function is not supported To proceed the Update, go through same steps from Step 5 to Step 8 of 9-5-1.All(Firmware, RAM disk, System, Web) Update. 9-5-3.Web Only Update This function is not supported To proceed the Update, go through same steps from Step6 to Step8 of 9-5-1.All(Firmware, RAM disk, System, Web) Update. 9-5-4.Sensor Device Driver Update Displayed on Menu, but function is not implemented 9-5-5.
■ Ikegami Electronics (U.S.A.), Inc. 37 Brook Avenue, Maywood, New Jersey 07607, U.S.A. Phone: 201-368-9171/FAX (201)569-1626 ■ Ikegami Electronics (U.S.A.), Inc, West Coast Office 2631 Manhattan Beach Blvd., Redondo Beach, C.A. 90278 Phone: 310-297-1900/FAX (310) 536-9550 ■ Ikegami Electronics (Europe) GmbH Ikegami Strasse 1, D-41460 Neuss, Germany Phone:.02131-123-0/FAX 02131-102820 ■ Ikegami Electronics (Europe) GmbH U.K.
