7 proscription Thank you for purchasing AKIN LIVESTOCK full-duplex wireless Intercom system. With the SECT protocol technology, LIVESTOCK Is widely sad In the areas of studio, stage events, EFP, webcasting, film making etc. With a clean line of sight (LOS), the transmission range of LIVESTOCK reaches up to 300m with full-duplex wireless communication and carrier-grade voice quality. I KEY FEATURES » 1000ft Communication Range, Carter-Grade Vole Quality » 1.
I roofing LIST EB OPTIONAL ACCESSORIES: {Not Included In the standard pecking Hat) * Headset Professional Electric Sade-Ear Headset Sade-Ear Mobile Earphone Air Duct Earphone Earmuffs Professional Dynamic Double-Sided Headset » TALLY Cable TALLY Set (TALLY Switcher, Connector, External TALLY Light} » Antennas Dual polarization high-gain panel antenna Antenna Extender + Packing Hard Case Package » Installation Base Station Ear Hanger Belt pack Cold Shoe + Charger 5-Port USB Belt packs Charger {Can be configu
BE standard SETUP The baas station of this wireless full-duplex intercom system supports up to 4 belt packs. The base station and the belt packs support dynamic and electric mics. They could be switched by selecting different applications in the menu. The 4-pin audio interface on the base station enables the device to connect with other audio systems, which can Increase the quantity of belt packs and also the wireless communication range.
EE PRODUCT INTERFACES MGR ZIPPING PIN-PING 8.
EE PRODUCT INTERFACES EY BASE STATION 2028 ©0006 VO RF Antenna Interfaces DC Power Supply (4-Pin XLR Male) 4-Pin Audio Input/ Output (RJ45) F370 Battery Plats 4 USB Type-A Interfaces (For Belt packs Charging and Cable Connection) Type-C USB Debugging Interface Power Switch Up/Left Button Menu/Confirm Button (Long Press to Enter Menu/Click to Confirm) Down/Right Button Remote Belt pack Mic Mute Button 3.
cusp Dis Play Wan LINK oJ ul_L2% MUTE — — TALK A B ©e6e 60 eee oon BASE STATION Belt pack Signal Strength Backpack Real-Time Battery Status (Actual percentage will bs displayed when the battery is lower than 20%) Belt pack Current Status F870 Battery 1 Low Battery Indicator F970 Battery 2 Low Battery Indicator Belt pack Number BELT PACK Belt pack Signal Strength Belt pack Real-Time Battery Status (Actual percentage will be displayed when the battery Is lower than 20%) Battery Charging Indicator Belt pack Nu
I ease STATION MENU FUNCTION INTRODUCTION Lang press tha Memy/Conflrm/OK button for about three seconds to attar the root menu, select the folder and press "OK"to rents the next menu. Each menu features introduced as follows. El Select “Mic Options” ard press “OK” bunion to enter the secondary msn of Mic Melting 1.1. Sal act “Mic Type” and press “0K” io enter the third-lees! many of Mic Setting; 1.1.1. Select “Dynamic” and press “0K” to switch to dynamic mic mode; 1.1.2.
I ease STATION MENU FUNCTION INTRODUCTION BO Select “System” and press “0K” 10 enter the secondary menu of system selling 4.1. Select “Information” and press “OK to enter the third-level menu of Information inquiry; 4.1.1. “Mic Type” displays the current mic type; 4.1.2. “Mic Gain” displays the current mic gain; 4.1.5. “Input Galen” displays the current 4 wire input gain; 4.1.4, "Output Gain” displays the current 4 wire output gain; 4.1.5. “Version” displays the current firmware version number; 4.2.
I OUTPACE MENU FUNCTION INTRODUCTION Mistypes. Bray = | Too OQ Gc Information Exit Long press the "OK" button for about three seconds to enter the root menu, select the many and press "OK" to enter the next label, Each many features ls described as follows.
I OUTPACE MENU FUNCTION INTRODUCTION El Select “Pair” and press “0K bunion to enter the secondary menu of the registration feature 1.1. Connect the backpack with the base station with a USB cable and select any 1D from 1 to 4 then press “0K” to register the belt pack. *Pairing...” will be displayed on the main interface of the backpack and the bass station. Unplug the USE cable after “Pairing Successful” is displayed on the screen of both of them.
BB installation @ Base Station installation 1. Install antennas as demonstrated. 2. Connote the power adapter and ths headset, 3. Press the power switch to peritonitis.
BB installation @ Belt pack Installation 1. Connect headset as demonstrated. 2. Turn the power and volume contra knoll to turn on ths backpack. 3. When the status of the belt pack turns from "LOST" ts "MUTE", long press the “MUTE/TALK® bunion on the side of the tailback to switch it to “TALK mode to communicate. [f the backpack operator wantonness to talk with the bass station, double click the "MUTE/TALK" button on the side of the backpack to sandwich to "MUTE" mode.
BB installation @ Repairing # any backpack 1D ls lost while using the system resulted by Incorrect operation or other reasons, connect the baas station and the backpack through the standard USB type-C data cabal. Enter ths pale menu and selects a master station vacancy 1D for registration on the belt pack. “Pairing...” will appear on the main Interface of the bass staleness and the belt pack.
EE ro I SAFETY NOTE Do not place your belt packs on heating equipment, cooking equipment, high pressure containers {such as microwave ovens, induction cookers, electric ovens, heaters, pressure cookers, water heaters, gas stoves, etc.) to prevent the battery from overheating and exploding. The original mating type of charger, data cable, and battery must be used.
EE ro BHO SOUND BETWEEN THE BASE STATION AND BELT PACK 1. Confirm if the “REMOTE MIC KILL" button on the base Station is on. If the red light is on, click on ditto turn it off. 2. Check the current status on the belt pack screen. If it's on “MUTE”, long press the “MUTE/TALK" button on the side to switch it to “TALK. 3. Check If the headset functions well and If you wear the headset and mic properly.
Wicca-n kan International 11800 8. Sam Houston Hwy West Houston, TX 77031 TEL 713.272.