Instruction Sheet

2-in-1 Wireless Charger
Model: iW18
-1 +1 Auto
DST
usb charging
DST Switch
(Daylight Savings)
DC 9V, 2.5A
Connect AC adapter to DC Jack, and plug into outlet.
Supports:
• Qi compatible phones (also works with plastic cases up to 3mm thick)
• AirPods with wireless charging case
Place Qi compatible device face up on the charging rest. Charging status will be indicated on display:
press down whole unit to snooze and to dim display
Wireless
Charging
Area
Battery Backup
Compartment
(for clock accuracy)
TIME SET/DIMMER
REAR CONTROLS
ALARM SET
SET
- Press to increase/decrease
time & settings
*Before use, remove battery
pull tab from bottom panel.
USB Charging
(5V/1A)
DC Jack for
power supply
(9V/2.5A)
WIRELESS CHARGING
OVERVIEW
Low Backup Battery Indicator
Alarm Indicator QI Charge Status Indicator
PM Indicator
- Press to Preview
- Press Again to Arm/Disarm Alarm
- Press & Hold to Set Alarm
(adjust with +/- and press alarm to confirm)
CAUTION: Remove phone’s metal protective case before charging. Do not place magnetic or metal objects
on charger during charging. Qi compatible phones with metallic looking finishes will charge normally.
SNOOZE
- Press & Hold to Set Clock
(adjust with +/- and press time
to confirm)
- Press to Adjust Display Brightness
(cycle for 5 brightness levels,
including OFF)
- Press Top Surface to Snooze Alarm
- Press & Hold to Adjust Snooze Duration
(adjust with +/- and press Snooze to confirm)
Note: Icon may continue to blink slowly when iOS devices are fully charged.
Device is not charging (reposition device)
Device is charging
Device is fully charged
Rapid blinking icon:
Slow blinking icon:
Solid icon:
For questions, full instructions, warranty, and additional
safety information, please scan the QR code or visit:
www.ihome.com/help/iW18
iW18_new Qi_112019-D
Printed in China
© 2019 SDI Technologies, Inc.
All rights reserved
FCC Information
This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment.
This device complies with Part 15 of the FCC Rules, operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
• Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the
user’s authority to operate the equipment.
• NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
CAN ICES-3 (B) / NMB-3(B), CAN RSS216 / CNR-216
IC Statement
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic
Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference, including interference that may cause undesired operation of the device.
The device meets the exemption from the routine evaluation limits in section 2.5 of RSS 102 and compliance with
RSS-102 RF exposure, users can obtain Canadian information on RF exposure and compliance.
This equipment should be installed and operated with a minimum distance of 20 cm between the radiator and your body.
L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d’Innovation, Sciences
et Développement économique Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée
aux deux conditions suivantes :
(1) L’appareil ne doit pas produire de brouillage;
(2) L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre
le fonctionnement.
Le dispositif rencontre l'exemption des limites courantes d'évaluation dans la section 2.5 de RSS 102 et la conformité à
l'exposition de RSS-102 rf, utilisateurs peut obtenir l'information canadienne sur l'exposition et la conformité de rf.
Cet équipement doit être installé et utilisé avec une distance minimale de 20 cm entre le radiateur et votre corps.
CAUTION - RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES
ACCORDING TO THE INSTRUCTIONS.
The socket-outlet shall be installed near the equipment and shall be easily accessible.
FCC ID: EMOIW18A IC: 986B-IW18A
POWERVALET
iW18 - Instruction Sheet (New Qi module) - English
Color: Black text on white paper (1C + 1C)
Size: 102 W x 150 H mm
Material: 85gsm wood free paper
Nov. 20, 2019
SDI Technologies Inc.
Addresss: 1299, Main Street, Rahway, NJ 07065, U.S.A.
Telephone: [phone]
E-mail: [e-mail]