Installers & User guide Smart IoT Deadbolt. Version 0.
Welcome! This guide will get you up and running with your igloohome Smart IoT Deadbolt. In the meantime, you should follow igloohome on Facebook and Youtube! Like us on Facebook Visit our Youtube As our iglooworks app is frequently updated, there may be changes to this manual. Please refer to our website igloohome.co/support for the latest version of the manual.
Table of Contents What’s Included 4 Specifications 5 Installation Guide Requirements 6 Prepare Door for Installation 7 Prepare Lock for Installation 9 Installation Instructions 10 Test Lock 17 Prepare the Door Frame 18 User Guide Lock Anatomy 19 Features 20 Unlocking and Locking 22 Lock Pairing & Provisioning 23 iglooworks App Functions 24 Lock Behaviour 25 9V Jumpstart Feature 26 Audio and LED Indications 27 Troubleshooting 28
What’s Included Back Plate Back Assembly Rubber Gasket Front Assembly & Rubber Gasket Back Assembly AA Alkaline Batteries x8 Strike Plate Housing & Strike Plate Bolt Assembly 10mm (Optional) Fold this line Drill for: 60mm (2-3/8”) backset Keyhole Cover x1 Construction Keys x4 Permanent Keys x4 03/18 Face of the door 8mm (0.31”) Bolt Screw x4 Drill for: 70mm (2-3/4”) backset Version 0.2 Edge of the door 4mm (0.16”) Bolt Screw x2 Drill Sheet 6mm (0.
Specifications Model igloohome Smart IoT Deadbolt Battery Type 8 x AA* Alkaline Battery Life Up to 1 Year Emergency Power 9V Alkaline Battery Operation Temp -25°C to 55°C Storage Temp -40°C to 70°C IP Rating IP65 Material AI, Zinc Alloy, ABS Weight Net: 450g, Gross: g Unlock Mechanism Bluetooth, PIN code, Physical Keys, Thumbturn Side Back 145mm (5.70”) 185mm (7.28”) Front 60mm (2.36”) 11mm (0.43”) 58mm (2.28”) 76mm (2.
Installation Guide Requirements Clearance Door Thickness a b 185mm (7.28”) 145mm (5.70”) b e b c d Measurements 6 a 45mm (1.77”) to 80mm (3.15”) b 10mm (0.39”) c 20mm (0.78”) d >110mm (4.33”) for 60mm (2.36”) / >120mm (4.72”) for 70mm (2.75”) backset e 50mm (1.
Prepare Door for Installation Items needed: Drill Sheet #2 Phillips Screw Driver Recommended Door and door frame material : Wood Drill 25mm (0.98”) Spade Bit 10mm (0.39”) Drill Bit 20mm (0.78”) Chisel 54mm (2.12”) Hole Saw Hammer Recommended Gap between door and door frame: <3mm (0.01”) Please ensure that there is an existing handle on your door for push - pull access. Not for: metal gates, glass doors or sliding doors.
How to use the Drill Sheet Drilling (Door) Fold here before drilling holes for side 10mm (0.39“) Drill Bit Make sure this is aligned to the centre of door edge 25mm (0.98”) Spade Bit 54mm (2.12”) Hole Saw Door edge 54mm (2.12”) Deep 54mm (2.12”) Chiselling 25mm (0.98”) Put the bolt tongue in & chisel around the edge 57mm (2.25”) 20mm (0.78”) Chisel 20mm (0.78”) Chisel Mark the center of the holes and then drill for accuracy.
Prepare Lock For Installation Set Back Assembly for Left / Right Hand Installation Left Hand Installation Set the toggle to ‘L’ for left-hand installation Hinge * Hinge is on your left. Outside Right Hand Installation Set the toggle to ‘R’ for right-hand installation Hinge * Hinge is on your right.
Installation Instructions Measure If you are replacing your current deadbolt lock, industry standards are 60mm (2.36”) or 70mm (2.75”) backset. To determine which backset length you should use, so measure the distance (x) between the center of 54mm (2.12”) hole to door edge. 54mm (2.12”) Hole X Prepare bolt assembly based on the distance (x) Bolt ships with bolt assembly in 60mm (2.36”) position. If required, twist the bolt and pull to extend (Simultaneously) to 70mm (2.75”) backset position.
Insert bolt and front assembly into door edge The ‘+ ‘ hole on the backset should be in the middle of the hole. Screw Holder c c Screws Please ensure that tailpiece is in horizontal position of INB1 15mm (0.59”) Measure and cut the tailpiece if necessary After inserting the tailpiece, measure the distance of protrusion from the door. If the door thickness is 70-80mm, you will not need to cut tailpiece during installation. Notch Door thickness (mm) No.
Secure the Front Assembly using the Back Plate. To do this, place the Back Plate (ensuring the correct side placement). d d Screws Follow this orientation d 40mm (1.57”) 5 Door Sensor Installation Adjust the position of the door sensor according to the door handling (left or right hand installation). Use the 2 x 5mm (0.24”) screws to secure the door sensor to the back plate. Right-hand Installation Left-hand Installation Do not overtighten the screws e e e e Screws e 12 4mm (0.
6 Fit in the Rubber Gasket Insert the front assembly cable through the rectangular hole on the rubber gasket. The hole should be on the right side of the rubber gasket.
7 Connect Assembly Cable Connect the sensor cable to the Back Assembly then connect the assembly cable from the Front assembly through the 54mm (2.12”) hole to the Back Assembly. Ensure that the wire is installed properly and securely. Door Sensor Cable Assembly Cable 8 Fit Back Assembly to the Door Tailpiece Ensure thumbturn position is turned to ‘unlock’ position.
9 Secure the Back Assembly Do not overtighten the screws Screws 8mm (0.31”) 10 Install SIM Card to the Communications Module Remove the communications module from the top of the unit. On the bottom of the communications module, you’ll see a SIM card sticker label and a SIM card slot. Insert your SIM card into the SIM card slot following the SIM card sticker label direction.
11 Insert 8 AA Alkaline Batteries and slide the battery cover downwards to close Before inserting the batteries, please ensure the ribbon is spread across the battery compartment for easier battery removal in the future. It is optional to secure the battery cover further with the additional screw. Top View of Battery Cover Tighten the screw from the top to further secure the batter cover Side View Slide Down Screws 16 e 6mm (0.
Test Lock Place hand over your lock to activate touchpad and hold ‘Unlock’ icon to lock. Does your bolt lock? Yes No Congrats! Your lock is correctly installed. Proceed to next steps. Bummer! Does the bolt lock and unlock when you turn the thumbturn? Yes No Left-Right toggle incorrectly set Tailpiece and/or thumbturn incorrectly set Troubleshoot: Try Setting the left-right toggle on your back assembly to the correct side. (See Pg. 10) Troubleshoot: Dissemble lock and install it again.
Prepare the Door Frame Mark out where the bolt tongue locks then drill a corresponding hole on door frame. Chisel to fit the strike plate in as well. Ensure to align the lock to the door frame and mark it down. Door Frame 20mm (0.78”) Chisel 25mm (0.98”) Spade Bit 26mm (1.02”) Mark & Drill Hole 58mm (2.28”) Same height Secure strike plate housing and strike plate using 2x 25mm (0.98”) wood screws. 4 Paste the magnet opposite the door sensor. Door Sensor Magnet 1mm (0.
User Guide Lock Anatomy Front & Back Assembly Touch Screen Keypad Battery Cover Unlock LED Indicator Key hole Cover (Remove cover to access physical key unlock) Thumbturn 9V Jumpstart Clear Downlight LED 19
Features PIN / Bluetooth Unlock Master PIN Code Bluetooth Key The igloohome Smart IoT Deadbolt unlocks with a permanent Master PIN Code. The igloohome Smart IoT Deadbolt unlocks with Bluetooth via the app. User PIN Code The iglooworks management dashboard can generate multiple types of User Pin codes, e.g. One-Time, Permanent & Duration. Lock Auto Re-lock Manual Locking The igloohome Smart IoT Deadbolt relocks automatically when door is closed.
Features Security / Alarms Keypad Security Lockout Activity Logs Be assured with an additional layer of security with the keypad lockout if the keypad is being tampered. User can configure number of incorrect attempts to trigger lockout. Entry via PIN codes and Bluetooth Key will be logged in the app. Masking Security Code Tamper Alarm Enter up to 8 digits before your PIN Code to reduce risk of intruders checking fingerprints. The lock will sound if intruders try to pry the lock from the door.
Unlocking & Locking iglooworks App Bluetooth Unlock PIN Code Lock INB1 INB1 Last synced: a minute ago Moderate Change batteries in 9 months SYNC SYNC & UNLOCK Master PIN Physical Key Lock Settings Thumbturn Unlocking PIN Code Key in your PIN code and press ‘Unlock’ icon Bluetooth Unlock On your app, click on the Bluetooth Unlock button and tap on your lock Thumbturn Use thumbturn at the back of lock Physical Key Use the physical key to unlock the door ‘Unlock’ Key Press and hold ‘Unlock’ Physi
Lock Pairing & Provisioning Test Factory PIN Unlock In the factory mode (before pairing), the PIN to unlock is 2 1234567890 Register as a Admin/Owner a) Use the iglooworks management dashboard to send invitation of registeration to the user. b) Create the account via the link in the invitation and login. 3 Pairing Pairing a) Click on the 3 dashes on the top left of the screen, and select [Pair New Lock]. Place palm overk eypad to activate the device.
iglooworks App Functions Setting Master PIN code Before proceeding, turn on your Bluetooth and ensure that you are within Bluetooth range of the lock. Go to the lock page and select [Master PIN]. 2 Setting the Lock’s Beep Volume Go to the lock’s page, select [Lock Settings], select [Set beep volume], Choose your preferred volume from the choices provided, click on the Apply Changes button on the bottom of the page.
Lock Behaviour Keypad Security Lockout After several incorrect PIN code attempts, the igloohome Smart Smart IoT Deadbolt keypad will be locked out and the security alarm will be triggered. Note: Physical key and Bluetooth Unlock can be used to unlock in this mode. Keypad Security Lockout Triggered by 5 consecutive PIN Code attempts by default (Configurable via Bluetooth) Disable By After 1 / 5 / 10 Minutes or Any other unlocking methods Behaviour Single flash when keypad is triggered.
9V Jumpstart Feature 1. Touch and hold the battery contacts against the 9V jumpstart pin on the lock and you will hear a series of beeps and the keypad will light up. 2. While holding the 9V battery to the jumpstart, key in your PIN code on the keypad followed by the ‘Unlock’ icon 9V 9V 9V 9V Please ensure terminals of the 9V battery are in contact with the Jump Start contact points of the lock for 2 seconds to activate your Smart IoT Deadbolt.
Audio and LED indications Actions Indications Bluetooth Connection ‘Unlock’ icon flashes Blue Successfully Unlocked 4 fast ascending tones after unlocked Successfully Locked 1 long beep after lock is locked Incorrect PIN 4 short beeps Deleted PIN 3 sets of 4 short beeps Obstruction Alarm 6 sets of 4 short beeps Keypad Disabled Mode Activated Very long beep Keypad Disabled Mode Deactivated 2 short beeps Keypad Security Lockout Alarm Low-high siren for 30 /60 / 90 seconds Keypad Security L
Troubleshoot The lock is not responding at all. I have generated my PINs from the app but it doesn’t work. • The lock’s battery is flat. • Use an Alkaline 9V Battery to jumpstart the lock and unlock the lock to replace the batteries once you are able to access the battery compartment. • Do a Bluetooth Unlock or sync and try again. • Make sure that the generated PIN codes are activated within the activation period before it expires. The deadbolt keypad flashes when I activate the keypad.
20c
For enquiries go to: igloohome.