LIW-1 Quick Guide This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) thisdevice must accept any interference received, including interference that may cause undesired operation. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
WiFi Kit Quick Guide Quick Guide WiFi Kits LIW-1 From this page This manual is suitable for firmware version of H4.01.40Y2.0.02W1.0.03+. QG-WE02-V1.
WiFi Kit Quick Guide WiFi Kit LIW-1 is an external data logger in the SolarMAN PV monitoring series. By connecting with single or multiple inverters through RS485/422/232 interface, the Kit can collect information of PV systems from inverters. With the integrated WiFi function, the Kit can connect to router and transmit data to the web server, realizing remote monitoring for users. In addition, Ethernet is also available for connection to router,enabling transmission of data.
WiFi Kit Quick Guide This Quick Guide is intended to assist users in quick installation and start of WiFi Kit LIW-1. If any problems, please refer to corresponding chapters of LIW-1 User Manual for details. A:Unpack I. Checklist After unpacking the box, please make sure all the items are contained as follows: 1 PV data logger (WiFi Kit LIW-1) 2 screws 1 power adapter with European or British plug 2 expandable rubber hoses 1 Quick Guide II.
WiFi Kit Quick Guide B:Install data logger WiFi Kit can be either wall-mounted or flatwise. Please refer to User Manual for details. C:Connect data logger and inverters Notice: 1. Power supply of inverters must be cut off before connection. Make sure that all connections are completed, then power the data logger and inverters, otherwise personal injury or equipment damage may be caused. 2. Basic version of WiFi Kit with RS485/422 port can be connected to up to 4 inverters at a time.
WiFi Kit Quick Guide Notice:The connectors of the connection cable may differ according to the brands and models of connected inverters. III. Line order of connector to WiFi Kit QG-WE02-V1.
WiFi Kit Quick Guide IV Confirm connection When connection between inverter and data logger is finished and with the power on for about 5 minutes, please check the 4 LEDs. If POWER, RS485/422 and STATUS are permanently on, the connection should be successful. If any problems, please refer to G. Debug. D:Connection setting The Kit can transfer information via either WiFi or Ethernet, users may choose the appropriate method accordingly.
WiFi Kit Quick Guide 3. Set WiFi connection to the data logger ○ 1Open wireless network connection and click View Wireless Networks 2 Select wireless network of the data logger, no passwords required as default. The network name consists of AP and ○ the serial number of the product. Then click Connect. QG-WE02-V1.
WiFi Kit Quick Guide 3 Connection successful ○ Notice: If AP_(serial number of product) is not available in the wireless network list, there may be problems in the connection or setting of data logger. Please refer User Manual for troubleshooting. 4. Set parameters of data logger ○1 Open a web browser, and enter 10.10.100.254, or http://wifi/ then fill in username and password, both of which are admin as default. Recommended browsers: Internet Explorer 8+, Google Chrome 15+, Firefox 10+ QG-WE02-V1.
WiFi Kit Quick Guide admin admin ○2 In the Status page, you can view general information of the data logger. ○3 Follow the setup wizard to start quick setting. (a)Click Wizard to start, then click Start to continue.. QG-WE02-V1.
WiFi Kit Quick Guide (b)Select Wireless connection, and select the type of your inverter, then click Next (c)Click Refresh to search available wireless networks, or add it manually. (d)Select the wireless network you need to connect, then click Next QG-WE02-V1.
WiFi Kit Quick Guide Notice: If the signal strength (RSSI) of the selected network is <15%, which means unstable connection, please adjust the antenna of the router, or use a repeater to enhance the signal. The SSID of your selected router network should be less than 30 characters, in which blank space should not be included. (e)Enter the password for the selected network, then click Next QG-WE02-V1.
WiFi Kit Quick Guide Notice: Router password cannot be recognized if it contains any character such as‘&’,'#',‘%',and blank space. The password is being verified, please wait for a while. If you have entered an invalid password or encryption method, an error notice will pop up. QG-WE02-V1.
WiFi Kit Quick Guide (f)Select Enable to obtain an IP address automatically, then click Next (g)Enhance security settings of the WIFI Kit by selecting any options as listed, then click Next. Option1 If you choose to hide AP, the SSID of the AP network for your WiFi Kit will be invisible on your wireless network list. Please reconfirm the IP address of the WIFI Kit on your router before you log in this server next time. QG-WE02-V1.
WiFi Kit Quick Guide Option2 If you wish to change the encryption mode of the AP network, you will need to enter the correspondent encryption method and password before you connect to this WIFI Kit next time. Option3 QG-WE02-V1.
WiFi Kit Quick Guide If you wish to change the user name and the password of the Web server, please enter the new username and password when you need to re-log in this server. (h)If setting is successful, the following page will display. Click OK to restart. (i)If restart is successful, the following page will display.If this page does not display automatically,please refresh your browser. QG-WE02-V1.
WiFi Kit Quick Guide (j) Re- log on this setting page to Status interface after the Web server restart, and check the network connection status of the data logger. Notice: After network setting is complete, the Wireless STA mode should be enabled and relative information of your router will display on the interface automatically. Besides the Remote server A should be pingable as the picture described. II. Connection via Ethernet 1.
WiFi Kit Quick Guide 3.Set network to the data logger Enter the configuration interface of your router, and check the IP address of the data logger assigned by the router. Open a web browser and enter the assigned IP address to get access to the configuration interface of the data logger. Fill in username and password, both of which are admin as default.
WiFi Kit Quick Guide ②Select Cable Connection and the type of your inverter, and you can choose to enable or disable the wireless function, then click Next 3 Please referring to Step (f) to (h) from page 12 for the following procedures. ○ E:Register on SolarMAN Portal QG-WE02-V1.
WiFi Kit Quick Guide Open a web browser and visit the portal website: http://www.solarmanpv.com/portal . Supported browsers: Internet Explorer 8+, Google Chrome 10+, Firefox 9+, Safari 4+ 1 Click Register Now ○ 2 Fill in your email address and password, then click Next ○ QG-WE02-V1.
WiFi Kit Quick Guide 3 Fill in the information as required, then click Complete ○ 4 If registration is successful, the following page will display. Click OK to return to the homepage of the portal. ○ QG-WE02-V1.
WiFi Kit Quick Guide F:Log in SolarMAN Portal to manage power station After successful registration and account activation, open the login page of SolarMAN Portal, and input the correct E-mail and password to access the monitoring system and start monitoring and management of power plants. Notices: If users access the monitoring system for the first time within ten minutes after successful registration, please check the "Real Time" interface as shown below.
WiFi Kit Quick Guide G:Debug I.
WiFi Kit Quick Guide II. Trouble shootings Phenomenon Meaning Solutions Power off No power supply Connect power supply and ensure good contacts. Check the connection cable, and ensure that the cable order comply with descriptions of part III in this text, or the line order described in Inverter quick RS485/422 off guide . Connection with inverter is abnormal Ensure the stability of RJ-45. Ensure that inverter is working under normal condition.
WiFi Kit Quick Guide III. Reset Press the reset button with a needle or open paper clip and hold for a while when the 4 LEDs should be on. Reset is successful when 3 LEDs, except POWER, turn off. H:Contact If any technical problems, please contact us, with the following information in hand: Device model Serial number of data logger Number of inverters connected Problem description Screen shot of Status page IGEN Tech. Co., Ltd. Add: Rm.405, BuildingA, Tian’an iPark, No.