80278591 / 01 03/2020 Installation instructions RF identification system Read/write head DTI600 UK
Content 1 Preliminary note ���������������������������������������������������������������������������������������������������4 1.1 Symbols used �����������������������������������������������������������������������������������������������4 2 Safety instructions �����������������������������������������������������������������������������������������������4 2.1 General ���������������������������������������������������������������������������������������������������������4 2.
12.1 Radio approvals ����������������������������������������������������������������������������������������14 12.1.1 Overview �������������������������������������������������������������������������������������������14 12.1.2 Europe / EC declaration of conformity ����������������������������������������������14 12.1.3 USA ��������������������������������������������������������������������������������������������������14 12.1.
1 Preliminary note This document is part of the device and contains information about the correct handling of the product. This document is intended for specialists. These specialists are people who are qualified by their training and their experience to see risks and to avoid possible hazards that may be caused during operation or maintenance of the device. Read this document before use to familiarise yourself with operating conditions, installation and operation.
2.2 Radio equipment In general, radio equipment must not be used in the vicinity of petrol stations, fuel depots, chemical plants or blasting operations. ►► Do not transport and store any flammable gases, liquids or explosive substances near the device. 2.3 Interference of electronic and medical devices Operation of the device can affect the function of electronic devices that are not correctly shielded. ►► Disconnect the device in the vicinity of medical equipment.
4.2 Overview Art. no.: Function: Type designation: Operating frequency: Type: Max. transmitter power: DTI600 read/write head DTRHF HLRWIOUS03 13.56 Mhz rectangular 2 watts 5 Installation 5.1 General installation instructions When mounting several read/write heads adhere to the minimum distances between the systems. Installing a read/write head in or on metal reduces the read and write distance.
5.3 Avoiding interference The device generates a modulated electrical field with a frequency of 13.56 MHz. To avoid interference of the data communication no other devices generating interference emission in this frequency band must be operated in its vicinity. Such devices are for example frequency converters and switched-mode power supplies. 5.4 Mechanical design 1 UK 2 1: Sensing face 2: Connection (can be rotated by 270°) 5.5 Fixing For installation, the following optional accessories are available.
5.5.2 Installation with mounting device E80336 The mounting device is used to mount the device to a clamp. The following clamps can be used: ● E21110 with a rod diameter of 12 mm ● E20795 with a rod diameter of 14 mm ● E21109 with a rod diameter of 14 mm 5.5.3 Installation with fixing bars E80337 ►► Fix the device with fixing screws to the designated location.
5.6 Mounting distances UK Operating mode For reading and writing Distance side (A) ≥ 600 mm Distance front (B) ≥ 400 mm 5.7 Positioning of the ID tags D ►► Align the ID tag on the antenna central axis.
6 Electrical connection Observe the following instructions before electrical installation. NOTE The device must be connected by a qualified electrician. Observe the electrical data in the data sheet. Device of protection class III (PC III). The electrical supply must only be made via PELV/SELV circuits. ►► Disconnect power before connecting the device. 6.1 Wiring ►► Connect the device to the IO-Link master using the M12 connector. Voltage is supplied via the IO-Link master.
7 Indicators 1 2 UK 1: LEDs 2: Sensing face LED green Status ON OFF FLASHING SLOWLY ON (permanently) ON (pulse) FLASHING QUICKLY OFF Meaning operating voltage OK operating voltage missing deactivated 4 x yellow ID tag detected ID tag read /written successfully error when reading/writing on ID tag no ID tag in the field or faulty ID tag in the field or invalid ID tag in the field green + 4x yellow FLASHING ALTERNATELY device fault 8 Operation The read/write head is configured via the IO-Link master.
9 Scale drawing 50 88 64 12,5 2 113 113 120 1 12,4 M12x1 The max. tightening torque of the screws when mounting the device is 0.8 Nm.
10 Technical data The data sheets are available on our website at www.ifm.com. 10.1 Detection range with E80384 [mm] 220 170 UK 120 70 20 -200 -150 -100 -50 0 50 100 150 200 [mm] Detection zone All indications apply to static write operations. If not otherwise stated, they refer to the installation of the device and of the ID tag in a non-metallic environment. 11 Maintenance, repair and disposal The operation of the device is maintenance-free.
12 Approvals/standards If approval is granted the approval text of the respective countries applies (→ 12 Approvals/standards). Information about the approvals granted: www.ifm.com 12.1 Radio approvals 12.1.1 Overview The overview of the approval status of a unit is available on our website at www. ifm.com. 12.1.2 Europe / EC declaration of conformity ifm electronic gmbh hereby declares that the DTI600 radio system corresponds to the directive 2014/53/EU.
12.1.4 Canada IC note: This device complies with Industry Canada license-exempt RSS standards. Operation is subject to the following two conditions: 1. The device may not cause interference, and 2. the user of the device must accept any interference received, including interference that may cause undesired operation. 12.1.
12.1.6 Australia Use in Australia: 12.1.7 Singapore Complies with IDA Standards DB 103032 The “Equipment Registration” is available on our website at: www.ifm.