User Manual Document: Project: Date: V-180131-BHA00 User Manual – SDoT Server V3B 20/09/2021
User Manual V-180131-BHA00 Table of Contents 1 Safety Informations....................................................................................................................................................................................................................................................................4 1.1 Intentional usage ...............................................................................................................................................................
User Manual V-180131-BHA00 4.2 Starting the SDoT Server V3B ......................................................................................................................................................................................................................17 4.3 LC-Touchdisplay – T1...............................................................................................................................................................................................................
User Manual V-180131-BHA00 Manufacturer iesy GmbH Darmcher Grund 22 D-58540 Meinerzhagen Germany 1 Safety Informations 1.1 Intentional usage To ensure safe operation, the system may only be operated in accordance with the information in these operating instructions. During use, the legal and safety regulations required for the respective application must also be observed. This also applies analogously to the use of accessories.
User Manual V-180131-BHA00 1.3 Safety Instructions Ground the unit properly do not use damaged power cords, accessories or peripherals 1.4 before cleaning or servicing, disconnect the unit from the power supply by disconnecting both power cables. Disconnect all connections, the potential equalisation at the front should only be disconnected if necessary and as a last step do not place or drop any objects on the unit.
User Manual V-180131-BHA00 1.6 Operating Installation Side Operating temperature: 0°C …+45°C make sure that the fans and ventilation openings are not covered up the permissible relative humidity at 45°C is 95 % (non-condensing) must be observed the device must be protected from direct sunlight 1.7 Service and Cleaning Clean the housing with a soft and slightly damp cloth. Never use solvents, as these could damage the labelling or the housing.
User Manual V-180131-BHA00 1.9 Modifications and Structural Changes The system may not be modified in terms of design or safety without our express consent. Any modification excludes liability on our part for any resulting damage. In particular, any repairs, soldering work on the circuit boards (replacement of components) are prohibited. When replacing entire assemblies, only original parts are to be used. The system was delivered from the factory with a fixed hardware configuration.
User Manual V-180131-BHA00 1.11 Symbols and Meanings Symbol: Meaning: Connection for grounding the connection must be at protective earth potential. Symbol: Meaning: CE-Marking With the CE marking, the manufacturer guarantees that his product complies with the requirements of the relevant EC directives.
User Manual V-180131-BHA00 2 Assembly SDoT-Server V3B The SDoT Server V3B is a 19" unit for use in server racks. Suspension bolts on the rear and eyelets on the front are used for mounting in 19" racks. Alternatively, mounting rails can be used to allow the unit to be pulled out of an IT cabinet for operation. The SDoT Server V3B 10G SC variant shown below has a smartcard slot and two 10 Gbit network ports (N5, N6).
User Manual V-180131-BHA00 3 Connection SDoT-Server V3B The AC power supply should be located close to the device and easily accessible, as this serves as a disconnecting device for the device. Alternatively, electronic components can be installed to ensure that the system is de-energised when actuated. Connect the two marked IEC plugs - redundant power supply unit iesy GmbH www.iesy.com | sales@iesy.com | Tel.
User Manual V-180131-BHA00 If a power unit is defective, you can replace the power unit. 1. switch off the SDoT Server V3B and remove it from the power supply 2. pull the plug out of the defective power supply unit 3. press the black locking lever in the direction of the bow handle 4. while holding the lever, pull the power supply out of the housing by the metal bracket 5.
User Manual V-180131-BHA00 3.
User Manual V-180131-BHA00 3.2 Server Rear Side The rear of the SDoT Server V3B has a battery compartment and two power supply units, the slide-in bolts and the openings for the fan module. 1 Insertion bolt in 19“-Rack 4 Mass fan module 2 Battery compartment 5 Power supplies 3 Fan module 6 Manufacturer´s device label 3.3 Main Power Supply 230 V-AC Input voltage, wide range input 90 ... 264 V-AC connector plug: 2 x cold appliance connector plug, incl.
User Manual V-180131-BHA00 3.4 Ground Connection Grounding/potential equalization of the device is mandatory. For this purpose, a grounding screw is provided on the front and marked with the grounding symbol 3.5 Interface USB3.0 – U1 & U2 For maintenance purposes only. These interfaces can be used to connect devices such as keyboard, mouse, printer or data storage devices such as USB sticks. 3.
User Manual V-180131-BHA00 3.9 LC Touch-Display Modul – T1 Grayscale LC display with a resistive touch 3.10 Reset-Button - R1 System reset button 3.11 Power on - Push-Button with LED - P1 The device is switched on via the P1 button. The integrated LED lights up green when the system is powered on. iesy GmbH www.iesy.com | sales@iesy.com | Tel.: +49 (2354) 70655 0 Local court Iserlohn | HRA 9826 | USt-IdNr: DE339671635 | Managing Director: Dipl.-Ing.
User Manual V-180131-BHA00 4 Operating SDoT Server V3B 4.1 Replacing the Audit-Hard Disk – H1 The SDoT Servers V3B has an audit hard disk that is installed in the form of a removable hard disk. This removable hard disk can be replaced. For information on the status and changing of the audit hard disk, refer to the user manual of the SDoT Product. Follow the steps below to securely change the audit disk 1. log in to the SDoT Server V3B as an auditor 2. open Status Audit system 3.
User Manual V-180131-BHA00 4.2 Starting the SDoT Server V3B After installing the SDoT Server V3B in a 19" IT cabinet and connecting it to the power supply using the IEC cables, the device can be put into operation. The basic steps for operating the SDoT Server V3B are described below. For detailed information, refer to the manual for your SDoT product. Put the SDoT Server V3B into operation: 1. press the on/off switch P1 2. follow the indication of the LC touch display T1 3.
User Manual V-180131-BHA00 5. the LC touch display shows the ident string a. check whether the ident string is unchanged and confirm this within 30 seconds with the checkmark key at the bottom right of the LC touch display 6. the LC touch display shows the start screen of the SDoT Product Startup Display of the SDoT Product (exemplary) The following describes the meaning of the symbols used on the LC touch display. 4.
User Manual V-180131-BHA00 1. In the left column, the LC touch display shows the status of (1) Operation, (2) Hardware Security Module (HSM) or Smartcard (SC) and (3) High Availability (HA) mode. The following table describes the individual symbols of these three statuses.
User Manual V-180131-BHA00 5. 4.4 Tap a menu item with your finger to display the settings System name IP addresses System date and system clock time Version information Shutdown and Restart You can use the LC touch display to both shut down and restart the SDoT Server V3B. 1. click on the menu button with the three horizontal lines (7) at the bottom right to display the menus 2. move the menu items with the arrow keys (5) downwards to the menu item Reboot / Shutdown system 3.
User Manual V-180131-BHA00 5 Waste disposal and Environmental protection All electrical and electronic products must be disposed of as hazardous waste. Proper disposal of old equipment prevents environmental damage and health hazards. Waste equipment that is no longer usable, in accordance with European regulations for environmental protection and raw material recovery, must be disposed of separately from regular household waste.
User Manual V-180131-BHA00 7 FCC Compliance FCC ID: 2AZ4S-SRV-19U-V3B CAN ICES-003(B) / NMB-003(B) „This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.“ The FCC ID nameplate is attached to the rear of the housing near the power supply. The label contains additional notes and warnings.
User Manual V-180131-BHA00 iesy GmbH www.iesy.com | sales@iesy.com | Tel.: +49 (2354) 70655 0 Local court Iserlohn | HRA 9826 | USt-IdNr: DE339671635 | Managing Director: Dipl.-Ing.
User Manual V-180131-BHA00 8 iesy GmbH Block diagram www.iesy.com | sales@iesy.com | Tel.: +49 (2354) 70655 0 Local court Iserlohn | HRA 9826 | USt-IdNr: DE339671635 | Managing Director: Dipl.-Ing.
User Manual V-180131-BHA00 Technical data 9 Type: SDoT Server V3B Operating voltage: 100 – 240 VAC Frequency: 50 – 60 Hz Current consumption: max. 5 A Unom: 230 VAC Fnom: 50 Hz Inom: 0,4 A Temperature: operation (+45 °C ± 2 °C / 16h) according to: GL VI-7-2:2012, Chapter 3b, Kap.6 Temperature: operation (0 °C ± 3 °C / 2h) according to: GL VI-7-2:2012, Chapter 3b, Kap.5 Weight: 12,5 Kg iesy GmbH www.iesy.com | sales@iesy.com | Tel.
User Manual V-180131-BHA00 10 iesy GmbH Dimensions (mm) SDoT Server V3B www.iesy.com | sales@iesy.com | Tel.: +49 (2354) 70655 0 Local court Iserlohn | HRA 9826 | USt-IdNr: DE339671635 | Managing Director: Dipl.-Ing.
User Manual V-180131-BHA00 11 Revision Tracking Date Revision Consultant Manufacturer Discription 25.08.2021 BHA00 KNO iesy Preparation WAR iesy Release iesy GmbH www.iesy.com | sales@iesy.com | Tel.: +49 (2354) 70655 0 Local court Iserlohn | HRA 9826 | USt-IdNr: DE339671635 | Managing Director: Dipl.-Ing.