h a n g e Vi e w N y bu to k lic c u -tr a c k w 1.4.4 Right Side Panel The right side panel of the panel PC provides access to a USB 2.0 port (Figure 1-6). 5 Enable or disable this USB port by pressing the function keys: . Figure 1-6: Left Side View 1.4.5 Rear Panel The rear panel has retention screw holes that support a wall-mounting bracket. Figure 1-7: Rear View Page 9 .d o m UPC-V312-D525 Panel PC o .c C m o .
h a n g e Vi e w N y bu to k lic c u -tr a c k 1.4.6 Frame (Function Keys) An aluminum frame surrounds the TFT LCD screen. The aluminum frame of the UPC-V312-D525 contains several function keys that control audio volume, LCD brightness and some other system components. Figure 1-8: Function Key Locations The following table describes the function of these function keys.
h a n g e Vi e w N y bu to k lic c u -tr a c k w 1.5 Dimensions The dimensions of the UPC-V312-D525 are shown in Figure 1-9 and listed below. 5 Figure 1-9: UPC-V312-D525 Dimensions (mm) Page 11 .d o m UPC-V312-D525 Panel PC o .c C m o .d o w w w w w C lic k to bu y N O W ! XC er O W F- w PD h a n g e Vi e ! XC er PD F- c u -tr a c k .
h a n g e Vi e w N y bu to k lic c u -tr a c k 1.6 Specifications The technical specifications for the UPC-V312-D525 system are listed in Table 1-4. 5 Specification UPC-V312-D525 LCD Size 12.1” Max. Resolution 1024 x 768 (XGA) Brightness 600 cd/m2 Contrast Ratio 700:1 LCD Color 16.2 M Pixel Pitch (mm) 0.240 (H) x 0.240 (V) Viewing Angle (H-V) 130 (H) / 150 (V) Backlight MTBF 50,000 hours SBC Model UPC-12AT-D525-R10 CPU 1.
h a n g e Vi e w N y bu to k lic c u -tr a c k w Optional GPS receiver Optional 3.75G HSUPA USB module Audio 2 x Audio speakers 1 x Digital microphone 1 x Line-out connector 1 x Mic-in connector Expansion 1 x PCIe Mini interface (installed with wireless LAN 802.
h a n g e Vi e w N y bu to k lic c u -tr a c k Output: 19 VDC Power Requirement Redundant dual DC input Terminal block: 9 (+/-3) V ~ 36 V DC jack: 10.5 (+/-0.3) V ~ 36 V Max. Power Consumption 52 W I/O Ports and Switches 1 x 9~36 V DC In terminal block (Power 1) 1 x 10.5~36 V DC In connector (Power 2) 1 x CAN-bus connector 1 x RS-232 port (COM1) 1 x RS-422/485 port (COM2) 5 x USB 2.
h a n g e Vi e w N y bu to k lic c u -tr a c k w Chapter 2 2 Unpacking Page 15 .d o m UPC-V312-D525 Panel PC o .c C m o .d o w w w w w C lic k to bu y N O W ! XC er O W F- w PD h a n g e Vi e ! XC er PD F- c u -tr a c k .
h a n g e Vi e w N y bu to k lic c u -tr a c k 2.1 Unpacking To unpack the panel PC, follow the steps below: WARNING! The front side LCD screen has a protective plastic cover stuck to the screen. Only remove the plastic cover after the panel PC has been properly installed. This ensures the screen is protected during the installation process. Step 1: Use box cutters, a knife or a sharp pair of scissors that seals the top side of the external (second) box. Step 2: Open the external (second) box.
h a n g e Vi e w N y bu to k lic c u -tr a c k w 2.2 Packing List The UPC-V312-D525 panel PC is shipped with the following components: Quantity Item 1 UPC-V312-D525 panel PC 1 Power adapter Image (P/N: 63040-010065-010-RS) 1 Power cord (P/N: 32702-000401-100-RS) 1 Power transfer cord (P/N: 32000-089400-RS) 1 RJ-45 to DB-9 COM port cable (P/N: 32005-000200-200-RS) 1 RS-422 cable (P/N: 32205-002400-100-RS) 1 Remote control (P/N: 7Z000-SLPCB001-RS) Page 17 .
h a n g e Vi e w N y bu to k lic c u -tr a c k 8 VESA mount screw (M8) (P/N: 44325-080081-RS) 8 VESA mount screw (M4*8) (P/N: 44005-040082-RS) 2 Mounting bracket (side panels) (P/N: 41003-0382C2-00-RS) 1 Screwdriver (P/N: 45019-001004-00) 1 One Key Recover CD (P/N: IEI-7B000-000478-RS) 1 User manual CD and driver CD If any of these items are missing or damaged, contact the distributor or sales representative immediately. Page 18 .d o m w o .c C m UPC-V312-D525 Panel PC o .
h a n g e Vi e w N y bu to k lic c u -tr a c k w Chapter 3 3 Installation Page 19 .d o m UPC-V312-D525 Panel PC o .c C m o .d o w w w w w C lic k to bu y N O W ! XC er O W F- w PD h a n g e Vi e ! XC er PD F- c u -tr a c k .
h a n g e Vi e w N y bu to k lic c u -tr a c k 3.1 Anti-static Precautions WARNING: Failure to take ESD precautions during the maintenance of the EP series may result in permanent damage to the EP series and severe injury to the user. Electrostatic discharge (ESD) can cause serious damage to electronic components, including the UPC-V312-D525. Dry climates are especially susceptible to ESD.
h a n g e Vi e w N y bu to k lic c u -tr a c k w configure the jumpers or plug in added peripheral devices, ground themselves first and wear and anti-static wristband. 3.3 Preinstalled Components The following components are all preinstalled. Motherboard TFT LCD screen DDR3 memory module Resistive type touch screen Stereo speakers Wireless module Webcam Preinstalled OEM customizations may include the following.
h a n g e Vi e w N y bu to k lic c u -tr a c k 3.4 CF Card Installation The UPC-V312-D525 has one CF Type II slot. To install the CF card, follow the instructions below. Step 1: Locate the CF card socket. The CF card socket is located on the left side panel of the UPC-V312-D525. Step 2: Remove the CF card slot panel by removing the four retention screws. NOTE: Please use the screw driver that comes with the UPC-V312-D525 to remove the screws on the chassis.
h a n g e Vi e w N y bu to k lic c u -tr a c k w Figure 3-2: CF Card Installation Step 4: Reinstall the CF card slot panel. Step 0: 3.5 Mounting the System WARNING: When mounting the panel PC onto an arm or onto the wall, it is better to have more than one person to help with the installation to make sure the panel PC does not fall down and get damaged.
h a n g e Vi e w N y bu to k lic c u -tr a c k Figure 3-3: VESA Mount Retention Screw Holes To enhance the stability, the user can use the mounting brackets, which are shipped with the UPC-V312-D525 and can be attached on both side panels. An additional mounting device is required for the mounting brackets. Figure 3-4: Mounting Brackets (Side Panels) NOTE: When mounting the UPC-V312-D525 on a vehicle, it is recommended to use the M8 mounting screws on the real panel.
h a n g e Vi e w N y bu to k lic c u -tr a c k w The following installation options are available: Arm mounting Stand mounting Wall mounting The mounting methods are described below. 3.5.1 Arm Mounting The UPC-V312-D525 can be installed on any arm that supports the standard VESA mounting interface. An example arm is shown below. Figure 3-5: VESA Compliant Arm To install the UPC-V312-D525 on the arm, follow the directions below. NOTE: Make sure the arm supports standard VESA mounting.
h a n g e Vi e w N y bu to k lic c u -tr a c k Step 4: Secure the flat panel PC to the interface pad by inserting four retention screws through the bottom of the mounting arm interface pad and into the flat panel PC. Step 0: 3.5.2 Stand Mounting The UPC-V312-D525 can be installed on any stand that supports the standard VESA mounting interface. An example stand is shown below. Figure 3-6: VESA Compliant Stand To install the UPC-V312-D525 on the stand, follow the directions below.
h a n g e Vi e w N y bu to k lic c u -tr a c k w Step 4: Align the wall-mounting bracket screw holes with the pilot holes. Step 5: Secure the mounting-bracket to the wall by inserting the retention screws into the four pilot holes and tightening them (Figure 3-7).
h a n g e Vi e w N y bu to k lic c u -tr a c k Figure 3-8: Chassis Support Screws NOTE: In the diagram below the bracket is already installed on the wall. Step 9: Secure the panel PC by fastening the retention screw of the wall-mounting bracket. (Figure 3-9). Page 28 .d o m w o .c C m UPC-V312-D525 Panel PC o .d o w w w w w C lic k to bu y N O W ! XC er O W F- w PD h a n g e Vi e ! XC er PD F- c u -tr a c k .
h a n g e Vi e w N y bu to k lic c u -tr a c k w Figure 3-9: Secure the Panel PC 3.6 Bottom Panel Connectors The bottom panel of the UPC-V312-D525 contains I/O connectors, switches and a reset button. These connectors are protected by an I/O cover. Detailed descriptions of the connectors and cabling can be found in the subsections below. 3.6.1 External Peripheral Device Connection To install external peripheral devices to the UPC-V312-D525, please follow the steps below.
h a n g e Vi e w N y bu to k lic c u -tr a c k Figure 3-10: I/O Cover Retention Screws Step 2: Connect the cable from the external peripheral device to the corresponding connector of the UPC-V312-D525 (Figure 3-11). Figure 3-11: External Peripheral Device Connection Step 3: Take out a rubber gasket from the I/O cover (Figure 3-12). Figure 3-12: Rubber Gasket Removal Page 30 .d o m w o .c C m UPC-V312-D525 Panel PC o .
h a n g e Vi e w N y bu to k lic c u -tr a c k w Step 4: Remove some rubber rings from the gasket to make the gasket fit perfectly to the size of the cable (Figure 3-13). Figure 3-13: Rubber Gasket and Cable Step 5: Repeat steps to other connected cables. Step 6: Install the I/O cover and make sure each rubber gasket snaps into place tightly. Figure 3-14: Reinstall the I/O Cover Step 7: Secure the I/O cover by the previously removed retention screws. Page 31 .d o m UPC-V312-D525 Panel PC o .
h a n g e Vi e w N y bu to k lic c u -tr a c k Figure 3-15: External Peripheral Device Connection Complete 3.6.2 ACC Mode Selection The ACC mode can be turned on or off. The setting is made through the ACC mode switch on the bottom panel as shown below. Figure 3-16: ACC Mode Switch 3.6.3 AT/ATX Power Mode Selection The UPC-V312-D525 supports both AT and ATX power modes. The setting can be made through the AT/ATX power mode switch on the bottom panel as shown below.
h a n g e Vi e w N y bu to k lic c u -tr a c k w 3.6.4 Audio Connectors The audio jacks connect to external audio devices. Microphone (Pink): Connects a microphone. Line Out port (Green): Connects to a headphone or a speaker. With multi-channel configurations, this port can also connect to front speakers. 3.6.5 CAN-bus Terminal Block There is one 3-pin CAN-bus terminal block. The pinouts are shown in Figure 3-18 Figure 3-18: CAN-bus Terminal Block Pinouts 3.6.
h a n g e Vi e w N y bu to k lic c u -tr a c k The RJ-45 Ethernet connector has two status LEDs, one green and one yellow. See Figure 3-19. LED Description LED Description A on: linked B off: 10 Mb/s blinking: data is being sent/received green: 100 Mb/s orange: 1000 Mb/s Table 3-2: RJ-45 Ethernet Connector LEDs To connect the UPC-V312-D525 to a network through the RJ-45 LAN connector, follow the steps below. Step 1: Locate the RJ-45 connector.
h a n g e Vi e w N y bu to k lic c u -tr a c k w 3.6.7 Power Input 1, 3-pin Terminal Block CN Label: POWER 1 CN Type: 3-pin terminal block CN Location: See Figure 1-4 CN Pinouts: See Figure 3-21 Connect the leads of a 9V~36V DC power supply into the terminal block. Make sure that the power and ground wires are attached to the correct sockets of the connector. Figure 3-21: 3-pin Terminal Block Pinouts 3.6.
h a n g e Vi e w N y bu to k lic c u -tr a c k Figure 3-22: RJ-45 RS-232 Serial Port Pin Description Pin Description 1 NDCD1 5 NTX1 2 NDSR1 6 NCTS1 3. NRX1 7 NDTR1 4. NRTS1 8 NRI1 Table 3-3: RJ-45 RS-232 Serial Port Pinouts To install the RS-232 devices, follow the steps below. Step 1: Locate the RJ-45 RS-232 connector. The location of the RJ-45 RS-232 connector is shown in Figure 1-4. Step 2: Insert the RJ-45 connector.
h a n g e Vi e w N y bu to k lic c u -tr a c k w Step 4: Secure the connector. Secure the serial device connector to the external interface by tightening the two retention screws on either side of the connector. 3.6.10 RS-422/485 Serial Port CN Label: RS 422/485 CN Type: 4-pin connector CN Location: See Figure 1-4 CN Pinouts: See Table 3-4 and Figure 3-24 A RS-422/485 serial port device can be connected to the RS-422/485 serial port on the bottom panel.
h a n g e Vi e w N y bu to k lic c u -tr a c k Step 3: Insert the serial connector. Insert the DB-9 connector of a serial device into the DB-9 connector on the RS-422/485 cable. Step 4: Secure the connector. Secure the serial device connector to the external interface by tightening the two retention screws on either side of the connector. Step 5: The DB-9 connector pinouts are listed below.
h a n g e Vi e w N y bu to k lic c u -tr a c k w The USB ports are for attaching USB peripheral devices to the system. The pinouts of the USB port is shown below. Pin Description Pin Description 1 VCC 5 VCC 2 DATA- 6 DATA- 3 DATA+ 7 DATA+ 4 GROUND 8 GROUND Table 3-6: USB Port Pinouts To install a USB device, follow the steps below. Step 1: Locate the USB connectors. The locations of the USB connectors are shown in Figure 1-4. Step 2: Align the connectors.
h a n g e Vi e w N y bu to k lic c u -tr a c k Step 3: Insert the device connector. Once aligned, gently insert the USB device connector into the on-board connector. 3.6.12 VGA Connector CN Label: VGA CN Type: 15-pin Female CN Location: See Figure 1-4 CN Pinouts: See Figure 3-28 and Table 3-7 The VGA connector connects to a monitor that supports dual display. The pinouts of the VGA connector is shown below.
h a n g e Vi e w N y bu to k lic c u -tr a c k w Step 2: Align the VGA connector. Align the male DB-15 connector on the VGA screen cable with the female DB-15 connector on the external peripheral interface. Step 3: Insert the VGA connector. Once the connectors are properly aligned with the insert the male connector from the VGA screen into the female connector on the UPC-V312-D525. See Figure 3-29.
h a n g e Vi e w N y bu to k lic c u -tr a c k 3.7 Redundant Power The UPC-V312-D525 is a system that supports redundant power. The redundant power input increases the reliability of the system while preventing data loss and system corruption from sudden power failure. The system can instantly and uninterruptedly switch to the second power input when the main power is unavailable or in low voltage capacity. There are two power connectors on the bottom panel.
h a n g e Vi e w N y bu to k lic c u -tr a c k w 3.7.1 ACC ON NOTE: In ACC On mode, the Power 1 connector must connect to the ACC on signal to be able to control system power. The ACC On mode is designed for vehicle applications. When the UPC-V312-D525 is in ACC On mode, the main power input is the Power 1 connector and the backup power is from the Power 2 connector. 3.7.1.
h a n g e Vi e w N y bu to k lic c u -tr a c k 3.7.1.2 Switch to Backup Power During operation, system power will switch from Power 1 to Power 2 automatically when the following situations occur: Power 1 < 9V and Power 2 > 10.5V Power 1 > 9V, but the ACC ON signal jump from high to low Power 1 is unplugged and Power 2 > 10.5V The following flow diagram shows how the power is switched between Power 1 and Power 2 and their LED statuses. Figure 3-33: ACC On: Switch Between PWR1 and PWR2 3.7.
h a n g e Vi e w N y bu to k lic c u -tr a c k w Figure 3-34: ACC On: Shutdown NOTE: To turn on the system in ATX power mode, press the button for three seconds. Press these two buttons for six seconds to turn off the system. 3.7.2 ACC OFF When the UPC-V312-D525 is in ACC Off mode, the main power input is the Power 2 connector and the backup power is from the Power 1 connector. 3.7.2.
h a n g e Vi e w N y bu to k lic c u -tr a c k Figure 3-35: ACC Off: AT Mode Figure 3-36: ACC Off: ATX Mode 3.7.2.2 Switch to Backup Power During operation, system power switches from Power 2 to Power 1 automatically when the following situations occur: Power 2 < 10.5V and Power 1 > 9V Power 2 is unplugged and Power 1 > 9V The following flow diagram shows how the power is switched between Power 2 and Power 1 and their LED statuses.
h a n g e Vi e w N y bu to k lic c u -tr a c k w 3.7.2.3 Shutdown The system will shutdown in the following situations: Power 2 < 10.5V and Power 1 < 9V Press buttons for 6 seconds The following flow diagram shows the system shutdown process and the LED statuses. Figure 3-38: ACC Off: Shutdown NOTE: The power LED turns off when the power cable is unplugged from the system. Page 47 .d o m UPC-V312-D525 Panel PC o .c C m o .
h a n g e Vi e w N y bu to k lic c u -tr a c k 3.8 Remote Control The UPC-V312-D525 comes with a remote control for easy configuration. Figure 3-39 6 shows the remote control and its function keys. Figure 3-39: Remote Control System On/Off: Press this button to turn the UPC-V312-D525 on or off. LCD On/Off. Press this button to turn the LCD monitor on or off. Auto-Dimming. Press this button to turn the auto-dimming function on or off. Brightness.
