IDS Ingegneria Dei Sistemi S.p.A. Hi-Pave – User Manual N doc:MN/2011/004 - Rev. 1.1 Config.: Hi-Pave-PRCS-OUT-MN - PRO/010/M1 Rev 4 - INGEGNERIA DEI SISTEMI S.p.A. Rev. 1.1 N°doc:MN/2011/004 Config.: Hi-Pave-PRCS-OUT-MN Hi-Pave System Assembly User Manual Hi-Pave – User Manual Pisa, December 2011 1 / 19 Tutte le informazioni sono di proprietà IDS. Tutti i diritti riservati. All information contained in this document is property of IDS.
IDS Ingegneria Dei Sistemi S.p.A. N doc:MN/2011/004 - Rev. 1.1 KEYWORDS: HI-PAVE, ENCODER, ANTENNA, FRAME SUMMARY: This manual explains the procedure of assembling the Hi-Pave GPR system in all its parts. Document Evolution Revision Date Reason of change Rev. 1.0 18/02/2011 First Edition Rev. 1.1 2/12/2011 FCC/IC Information added Versions covered by this document Contacts IDS Ingegneria dei Sistemi S.p.A.
IDS Ingegneria Dei Sistemi S.p.A. N doc:MN/2011/004 - Rev. 1.1 Disclaimer IDS WILL NOT BE HELD RESPONSIBLE FOR THE CONSEQUENCES OF AN IMPROPER USE OF THE EQUIPMENT AND/OR THE SOFTWARE. THIS SOFTWARE MAY INCLUDE AUTOMATED DATA PROCESSING AND ANALYSIS TOOLS.
IDS Ingegneria Dei Sistemi S.p.A. N doc:MN/2011/004 - Rev. 1.1 SAFETY INFORMATION The equipment conforms to the following requirements set by EC regulations, including subsequent modifications, and to the legislation set by the member states that implement these regulations: 1999/05/EEC Radio Directive Warning: this equipment is destined for use in industrial environments (Class A apparatus).
IDS Ingegneria Dei Sistemi S.p.A. N doc:MN/2011/004 - Rev. 1.1 IMPORTANT NOTE FOR THE US CUSTOMERS FCC ID: UFW-HR2000NA This device complies with part 15 of the FCC Rules: Operation is subject to the following conditions: 1. This device may not cause harmful interference, and 2.
IDS Ingegneria Dei Sistemi S.p.A. N doc:MN/2011/004 - Rev. 1.1 IMPORTANT NOTE FOR THE CANADIAN CUSTOMERS IC Certification Number: IC:8991A – HR2000NA This device complies with the requirements of IC Standard RSS-220 This Ground Penetrating Radar Device shall be operated only when in contact with or within 1 m of the ground.
IDS Ingegneria Dei Sistemi S.p.A. ! N doc:MN/2011/004 - Rev. 1.1 CLEANING INFORMATION WARNING Before cleaning any external parts of the apparatus, make sure that all cables have been disconnected, including the power supply cable. If a damp cloth is used, make sure it is not too wet, to avoid any damage to the electrical components of the equipment. Wait until the equipment is totally dry before reconnecting the cables. The Detector Duo should be cleaned periodically using a damp cloth.
IDS Ingegneria Dei Sistemi S.p.A. N doc:MN/2011/004 - Rev. 1.1 BATTERIES REMOVAL INFORMATION Laptop Batteries: Manufacturer: PANASONIC Type: Li-ion Ni Characteristics: 10.65V 5.7Ah Removal instructions: 1. turn off the laptop; 2. open the drawer with the symbol of the batteries; 3. extract the battery pack pulling the tab. Radar batteries: Manufacturer: FIAMM FG21202 / SAFT MP176065 Type: rechargeable lead acid / rechargeable lithium-ion Characteristics: 12V & 12Ah / 15V & 6.8Ah Removal instructions: 1.
IDS Ingegneria Dei Sistemi S.p.A. N doc:MN/2011/004 - Rev. 1.1 RECICLYING The crossed out wheeled bin symbol shown on the equipment indicates that the product must be recycled separately from other waste at the end of its useful life. Separate waste disposal of this product at the end of its useful life will be organised and managed by IDS. When you decide to dispose of the equipment, contact IDS and follow the system that IDS has set up to permit the separate collection of the apparatus at its life end.
IDS Ingegneria Dei Sistemi S.p.A. N doc:MN/2011/004 - Rev. 1.1 WARRANTY CERTIFICATE CONDITIONS 1) IDS Ingegneria dei Sistemi S.p.
IDS Ingegneria Dei Sistemi S.p.A. N doc:MN/2011/004 - Rev. 1.1 CONTENTS 1. Introduction ........................................................................................................................... 12 1.1 Purpose .......................................................................................................................... 12 1.2 Application Field ........................................................................................................... 12 1.3 Reference ..........
IDS Ingegneria Dei Sistemi S.p.A. N doc:MN/2011/004 - Rev. 1.1 1. INTRODUCTION 1.1 Purpose This manual explains the procedure of assembling the Hi-Pave GPR system in all its parts. Ids Hi-Pave system uses HR1000 and/or the HR2000 antennas; the model HR2000NA only is allowed to operate in the US and Canadian markets. 1.2 Application Field This system is dedicated for pavement applications on the asphalt and concrete roads.
IDS Ingegneria Dei Sistemi S.p.A. N doc:MN/2011/004 - Rev. 1.1 1. N.1 Aluminum Vertical Frame (A), with rectangular shape attached to a frame provided with a hook. 2. N.1 Aluminum Sliding horizontal frame (B) 3. N.1 Embossed white fiberglass frame (C). 4. N.2 Elastic belts 5. N.1 Horn Antenna + N.1 antenna cable 6. N.1 Encoder kit + N.1 wheel encoder cable 13 / 19 Tutte le informazioni sono di proprietà IDS. Tutti i diritti riservati. All information contained in this document is property of IDS.
IDS Ingegneria Dei Sistemi S.p.A. N doc:MN/2011/004 - Rev. 1.1 2. PROCEDURE OF ASSEMBLING Here below you find the steps to assemble the Hi-Pave GPR system. Of course it’s necessary to get a vehicle provided with a hook on the back side and possibly a carrier or similar on the roof/back of the vehicle itself. Please follow the steps in order one by one. 1. Take the metal key (provided with the system) and unscrew the screw on the vertical frame (see Errore. L'origine riferimento non è stata trovata.
IDS Ingegneria Dei Sistemi S.p.A. N doc:MN/2011/004 - Rev. 1.1 BRACKETS OF CONNECTION BETWEEEN HORIZONTAL AND VERTICAL FRAME Fig. 2-3 – Particular of the brackets to fix frame B to frame A 3. Remove the 2 caps from the horizontal frame (B) limbs; then insert embossed fiberglass frame (C) into the internal grooves of B until the end. Finally screw both screws for side of B and insert again the caps (see Fig. 2-4, Fig. 2-5, Fig. 2-6 and Fig. 2-7). Fig. 2-4 – Embossed Fiberglass frame (C) Fig.
IDS Ingegneria Dei Sistemi S.p.A. N doc:MN/2011/004 - Rev. 1.1 CAP CAP REMOVED Fig. 2-6 – Particular of the horizontal frame (B) limbs Fig. 2-7 – Particular of the white fiberglass frame (C) inserted into the internal grooves of the horizontal frame (B), with direction of insertion. 4. Arrange the 2 elastic belts and adapt them to the vehicle making them pass through the metallic slits located to the limbs of the fiberglass horizontal frame (C); then fix them on the other extremity to the vehicle (i.e.
IDS Ingegneria Dei Sistemi S.p.A. N doc:MN/2011/004 - Rev. 1.1 BELTS Fig. 2-9 – Particular of the belts 5. Insert the horn antenna onto the fiberglass frame in its proper place, located at the extremity of the frame C, between 2 black cross rubber bars; then fix the top of the antenna with the 2 straps already assembled properly. 6. The encoder kit (see Fig. 2-10) is composed by: a. 4 metallic cylinders (Ø17, or Ø19 or Ø21) b. 1 bigger metallic disk + 1 metallic star + 4 bigger screws c.
IDS Ingegneria Dei Sistemi S.p.A. N doc:MN/2011/004 - Rev. 1.1 Insert the 4 cylinders within the 4 nuts of the vehicle wheel and then apply on them the bigger disk, screwing it to them by fixing 4 bigger screws; then apply the smaller disk to the bigger disk by fixing the 4 smaller screws to the prefixed smaller cylinders. Keep vertical the encoder cable and apply the magnet located on its limb to the vehicle metallic side (see Fig. 2-11 and Fig. 2-12).
IDS Ingegneria Dei Sistemi S.p.A. N doc:MN/2011/004 - Rev. 1.1 7. Connect the wheel cable to the wheel port of the DAD control Unit and connect the antenna cable to antenna port of the DAD control unit. Fig. 2-13 – Final assembling of the Hi-Pave system 19 / 19 Tutte le informazioni sono di proprietà IDS. Tutti i diritti riservati. All information contained in this document is property of IDS.
