- P RO/010/M1 Rev 4 - INGEGNERIA DEI SISTEMI S.p.A. Rev. 1.0 Protocol: MN/2009/056 “RIS Hi-Mod System Installation Guide and User Manual RIS Hi-Mod Installation Guide and User Manual Pisa, August 2009 Tot pag. N°.
IDS Ingegneria Dei Sistemi S.p.A. RIS Hi-Mod - Installation Guide and User Manual Protocol: MN/2009/056 - Rev. 1.0 Document Evolution Revision Rev. 1.0 Date August 2009 Reason for change First edition OUR CONTACTS IDS Ingegneria dei Sistemi S .p.A. – GeoRadar Division Via Sterpulino, 20 56121 Ospedaletto (PISA) - ITALIA Tel: +39.050.967111 Fax: +39.050.967121 inforis@ids-spa.it Customer Care department: customercare.gpr@ids-spa.it Tel.: +39.050.967122 S ales & Marketing department: sales.gpr@ids-spa.
IDS Ingegneria Dei Sistemi S.p.A. RIS Hi-Mod - Installation Guide and User Manual Protocol: MN/2009/056 - Rev. 1.0 DISCLAIMER IDS WILL NOT BE HELD RESPONSIBLE FOR THE CONSEQUENCES OF AN IMPROPER USE OF THE EQUIPM ENT AND/OR THE SOFTWARE. THIS SOFTWARE MAY INCLUDE AUTOMATED DATA PROCESSING AND ANALYSIS TOOLS.
IDS Ingegneria Dei Sistemi S.p.A. RIS Hi-Mod - Installation Guide and User Manual Protocol: MN/2009/056 - Rev. 1.0 SAFETY INFORMATION The equipment conforms to the following requirements set by EC regulations, including subsequent modifications, and to the legis lation set by the member states that implement these regulations: 1999/05/EEC Radio Directive Warning: this equipment is destined for use in industrial environments (Class A apparatus).
IDS Ingegneria Dei Sistemi S.p.A. RIS Hi-Mod - Installation Guide and User Manual Protocol: MN/2009/056 - Rev. 1.0 IMPORTANT NOTE FOR THE US CUSTOMERS FCC ID: UFW-Hi-Mod This device complies with part 15 of the FCC Rules: Operation is subject to the following conditions: 1. This device may not cause harmful interference, and 2.
IDS Ingegneria Dei Sistemi S.p.A. RIS Hi-Mod - Installation Guide and User Manual ! Protocol: MN/2009/056 - Rev. 1.0 CLEANING INFORMATION WARNING Before cleaning any external parts of the apparatus, make sure that all cables have been disconnected, including the power supply cable. If a damp cloth is used, make sure it is not too wet, to avoid any damage to the electrical components of the equipment. Wait until the equipment is totally dry before reconnecting the cables.
IDS Ingegneria Dei Sistemi S.p.A. RIS Hi-Mod - Installation Guide and User Manual Protocol: MN/2009/056 - Rev. 1.0 BATTERIES REMOVAL INFORMATION Laptop Batteries: Manufacturer: PANASONIC Type: Li-ion Ni Characteristics: 10.65V 5.7Ah Removal instructions: 1. turn off the laptop; 2. open the drawer with the symbol of the batteries; 3. extract the battery pack pulling the tab.
IDS Ingegneria Dei Sistemi S.p.A. RIS Hi-Mod - Installation Guide and User Manual Protocol: MN/2009/056 - Rev. 1.0 RECICLYING The crossed out wheeled bin symbol shown on the equipment indicates that the product must be recycled separately from other waste at the end of its useful life. Separate waste disposal of this product at the end of its useful life will be organised and managed by IDS.
IDS Ingegneria Dei Sistemi S.p.A. RIS Hi-Mod - Installation Guide and User Manual Protocol: MN/2009/056 - Rev. 1.0 WARRANTY CERTIFICATE CONDITIONS 1) IDS Ingegn eria dei Sistemi S.p.
IDS Ingegneria Dei Sistemi S.p.A. RIS Hi-Mod - Installation Guide and User Manual Protocol: MN/2009/056 - Rev. 1.0 INDEX 1. Hardware equipment of the Hi-MOD system.........................................................13 1.1 One antenna equipment and configuration ........................................................13 1.1.1 Assemblage instructions ............................................................................14 1.1.2 Wiring...............................................................
IDS Ingegneria Dei Sistemi S.p.A. RIS Hi-Mod - Installation Guide and User Manual Protocol: MN/2009/056 - Rev. 1.0 FIG. 1-10 – M ET RIC WHEEL CABLE ...........................................................................18 FIG. 1-11 – ANT ENNA CABLE IN PLACE ...................................................................18 FIG. 1-12 – BAT T ERY CABLE AND LAN CABLE ......................................................19 FIG. 1-13 – EQUIPM ENT PROVIDED FOR T HE T WO ANT ENNAS CONFIGURAT ION ........
IDS Ingegneria Dei Sistemi S.p.A. RIS Hi-Mod - Installation Guide and User Manual Protocol: MN/2009/056 - Rev. 1.0 FIG. 3-2 – CLIENT DATA INSERT ION FORM .............................................................40 FIG. 3-3 – WEBEX SET UP WINDOW...........................................................................40 FIG. 3-4 – WELCOM E T O WEBEX SUPPORT CENT ER WINDOW ..........................41 FIG. 3-5 – COM M AND ACCEPT ANCE WINDOW ......................................................
IDS Ingegneria Dei Sistemi S.p.A. RIS Hi-Mod - Installation Guide and User Manual Protocol: MN/2009/056 - Rev. 1.0 1. HARDWARE EQUIP MENT OF THE HI-MOD SYSTEM Hi-M OD sy stem offers y ou the p ossibility to choose up to four different equip ments, matching the number of antennas y ou want to use. T his handbook shows y ou the equip ment y ou will receive and guid es y ou through the configuration of y our hardware. 1.1 One antenna equipment and configuration Fig.
IDS Ingegneria Dei Sistemi S.p.A. RIS Hi-Mod - Installation Guide and User Manual Protocol: MN/2009/056 - Rev. 1.0 1.1.1 Assemblage instructions First y ou have to set the rudder in its mono antenna setting. T he rudder has two free bars and four knobs (Fig. 1-2).
IDS Ingegneria Dei Sistemi S.p.A. RIS Hi-Mod - Installation Guide and User Manual Protocol: MN/2009/056 - Rev. 1.0 Now y ou have to build the frame carry ing the antenna: y ou will need the equip ment shown in Fig. 1-4. T ake one of the wheel frame and screw the two junction p ip es in it, then close the frame with the other wheel p art (Fig. 1-5). Fig. 1-4 – Antenna frame equipment Fig.
IDS Ingegneria Dei Sistemi S.p.A. RIS Hi-Mod - Installation Guide and User Manual Protocol: MN/2009/056 - Rev. 1.0 Fig. 1-6 – Insertion of the rudder Fig.
IDS Ingegneria Dei Sistemi S.p.A. RIS Hi-Mod - Installation Guide and User Manual Protocol: MN/2009/056 - Rev. 1.0 T ake the antenna and m ake it slide in the frame fro m b ehind. R emember to p ut and remov e the antenna alway s from the rear p art of the frame. When the antenn a is in p lace lock it around the two junction p ip es using its four hooks (Fig. 1-8). Fig.
IDS Ingegneria Dei Sistemi S.p.A. RIS Hi-Mod - Installation Guide and User Manual Protocol: MN/2009/056 - Rev. 1.0 1.1.2 Wiring Once the DAD unit is in p lace y ou have to connect it with the metric wheel, the antenna, the battery and y our lap top . T he metric wheel cable is located on one of the wheel frames. Let it p ass through the black strip on the rudder until y ou reach the first ferrite then link the conn ector with the Wheel p ort of the DAD unit (Fig. 1-10). Fig.
IDS Ingegneria Dei Sistemi S.p.A. RIS Hi-Mod - Installation Guide and User Manual Protocol: MN/2009/056 - Rev. 1.0 Battery cable has two connectors of different shap es in order to help y ou: one of them must be linked with the battery , the other one with the DAD unit (Fig. 1-12). Fig. 1-12 – Battery cable and LAN cable Fig. 1-12 shows also the LAN cable connector. You have to link the other end of this cable with the LAN p ort of y our lap top .
IDS Ingegneria Dei Sistemi S.p.A. RIS Hi-Mod - Installation Guide and User Manual Protocol: MN/2009/056 - Rev. 1.0 1.2 Two antennas equipment and configuration Fig. 1-13 shows y ou the equip ment y ou will receiv e for y our two antennas configuration.
IDS Ingegneria Dei Sistemi S.p.A. RIS Hi-Mod - Installation Guide and User Manual Protocol: MN/2009/056 - Rev. 1.0 Fig. 1-14 – Two antennas rudder configuration T o build the frame carry in g the antennas y ou need the equip ment shown in Fig. 1-15. Fig. 1-15 – Two Antennas frame equipment T ake one of the wheeled frames and screw two jun ction p ip es in it. Connect these p ip es with the non-wheeled frame (the white sp ots on it show y ou which side go es down).
IDS Ingegneria Dei Sistemi S.p.A. RIS Hi-Mod - Installation Guide and User Manual Protocol: MN/2009/056 - Rev. 1.0 Fig. 1-16 – Making the two antennas frame Fig. 1-17 – Insertion and locking of the rudder T ake the antennas and mak e them slide in the fram e from b ehind. Rememb er to p ut and remove the antennas alway s from the rear p art of the frame. When the antennas are in p lace lock them around the four junction p ip es using their hooks (Fig. 1-18).
IDS Ingegneria Dei Sistemi S.p.A. RIS Hi-Mod - Installation Guide and User Manual Protocol: MN/2009/056 - Rev. 1.0 Fig. 1-18 – Insertion of the antennas and close-up of the hook Place the DAD control unit inside the bo x on the rudd er and the b atteries in the two little black bags (Fig. 1-19). Fig. 1-19 – DAD unit positioning and Battery bags 1.2.2 Wiring Battery , wheel and LAN cables ar e linked to the DAD control unit as in the mon o antenna configuration (see Par 1.1.
IDS Ingegneria Dei Sistemi S.p.A. RIS Hi-Mod - Installation Guide and User Manual Protocol: MN/2009/056 - Rev. 1.0 Fig. 1-20 – Antenna cables You can find more info about the DAD unit and its cable conn ectors in Chap ter 2: T he DAD control unit.
IDS Ingegneria Dei Sistemi S.p.A. RIS Hi-Mod - Installation Guide and User Manual Protocol: MN/2009/056 - Rev. 1.0 1.3 Three antennas equipment and configuration Fig. 1-21 shows y ou the equip ment y ou will receiv e for y our three antennas configuration.
IDS Ingegneria Dei Sistemi S.p.A. RIS Hi-Mod - Installation Guide and User Manual Protocol: MN/2009/056 - Rev. 1.0 Fig. 1-22 – S ide antenna frames parts T ake one of the wheeled fram es and screw two junction p ip es in it. After that close the box usin g on e of the non-wheeled fr ames as shown in Fig. 1-23. Fig. 1-23 – S ide antenna frame Unite the side frame with the central one by linking the metallic lo cks with the wheels “mushrooms”. Lock up the structure by turning the switches (Fig. 1-24) .
IDS Ingegneria Dei Sistemi S.p.A. RIS Hi-Mod - Installation Guide and User Manual Protocol: MN/2009/056 - Rev. 1.0 “Mushroom” Locking device Fig. 1-24 – Main frame “mushrooms” & locking device T ake the antennas and make them slide in the side fram es from beh ind. Rem ember to p ut and remove the antennas alway s from the rear p art of the fram es. When the antennas are in p lace lock them around the junction p ip es using their hooks (Fig. 1-25). Fig.
IDS Ingegneria Dei Sistemi S.p.A. RIS Hi-Mod - Installation Guide and User Manual Protocol: MN/2009/056 - Rev. 1.0 Fig. 1-26 – Antenna cables Fig. 1-27 – Three antennas configuration You can find more info about the DAD unit and its cable conn ectors in Chap ter 2: T he DAD control unit.
IDS Ingegneria Dei Sistemi S.p.A. RIS Hi-Mod - Installation Guide and User Manual Protocol: MN/2009/056 - Rev. 1.0 1.4 Four antennas equipment and configuration Fig. 1-28 shows y ou the equip ment y ou will receive for y our four antennas configuration.
IDS Ingegneria Dei Sistemi S.p.A. RIS Hi-Mod - Installation Guide and User Manual Protocol: MN/2009/056 - Rev. 1.0 In the four antennas configuration y ou have four antenna cables. T o make a cascade connection between the antennas y ou have to link the lon ger cab le fro m the ANT 1/CHAIN p ort of the DAD unit to the IN p ort of the leftmost antenna; use the three short cable to link OUT and IN p orts of each adjacent antenna (Fig. 1-29). Fig. 1-30 shows the comp lete four antenna configuration. Fig.
IDS Ingegneria Dei Sistemi S.p.A. RIS Hi-Mod - Installation Guide and User Manual Protocol: MN/2009/056 - Rev. 1.0 2. THE DAD CONTROL UNIT T he DAD Control Unit is the control unit resp onsible for directing the antennas and digitalisin g the acquired r adar data. T he DAD Control Unit has the following p orts • Lan Port for a network connection to the Notebook Comp uter • Battery Port to connect the battery • Wheel Port to connect the p osition sensor wheel • Ant.1/CHAINE - Ant.
IDS Ingegneria Dei Sistemi S.p.A. RIS Hi-Mod - Installation Guide and User Manual Protocol: MN/2009/056 - Rev. 1.0 Ant1 and Ant 2 Wheel Port Connectors Fig. 2-2 – –DAD side Fast Wave with connections to position sensor and antennae Considerin g the typ e of available antenna, the following combin ations are p ossible: 1. Ant.1 (connector with 19 poles) T his kind of connector may be connected to the following categories of radar antennae.
IDS Ingegneria Dei Sistemi S.p.A. RIS Hi-Mod - Installation Guide and User Manual Protocol: MN/2009/056 - Rev. 1.0 Entire ran ge of TR IDS antennae that have an 11 p ole conn ector, if supp lied with an app rop riate 19-11 p ole adap tor (Fig. 2-4). Fig. 2-4 – 19-11 pole Adaptor 2. Ant.
IDS Ingegneria Dei Sistemi S.p.A. RIS Hi-Mod - Installation Guide and User Manual • Protocol: MN/2009/056 - Rev. 1.0 Graphics/Video Memory: Intel 945GM video accelerator with up to 128M B shared video memory • Wireless Networking: WLAN 802.11a/b/g, Bluetooth 2.0, Optional WWAN (EVDO, HSDPA) and GPS • Ports: T wo USB 2.0, Firewire, Ethernet, modem, h eadp hone, mic, do ckin g connector • Card Slots: PC Card T yp e II, SD Card slot • • • Weight: 5 p ounds Size: 10.7 x 8.5 x 1.
IDS Ingegneria Dei Sistemi S.p.A. RIS Hi-Mod - Installation Guide and User Manual Protocol: MN/2009/056 - Rev. 1.0 Fig. 2-6 – Lan Cable Fig. 2-7 – Lan Cable connection between the Notebook Computer and the DAD Control Unit • Connect the DAD Control Unit to the Battery usin g the Battery Cable (Fig. 2-8) as shown in (Fig. 2-9) Fig.
IDS Ingegneria Dei Sistemi S.p.A. RIS Hi-Mod - Installation Guide and User Manual Protocol: MN/2009/056 - Rev. 1.0 Fig. 2-9 – Connecting the DAD Control Unit to the battery pack and switching on button (red color) Press the red button to switch on the DAD control unit (Fig. 2-9 ). T his button has to be kep t p ressed until the blue on switch lights up . If the K2_FW software is not activated within 30 seconds, the indicator light will start to flash.
IDS Ingegneria Dei Sistemi S.p.A. RIS Hi-Mod - Installation Guide and User Manual Protocol: MN/2009/056 - Rev. 1.0 2.3 Wireless connection Here below y ou can see the requ irem ents and steps to connect by wireless DAD to PC: 1) Sy stem requirement: wireless network board of PC must supp ort network p rotocol typ e 802.11g. 2) Disconnect Lan cab le from DAD and from PC. 3) Connect the wireless p lug on LAN p ort of the DAD (Fig. 2-1 e F ig. 2-11).
IDS Ingegneria Dei Sistemi S.p.A. RIS Hi-Mod - Installation Guide and User Manual Protocol: MN/2009/056 - Rev. 1.0 Fig. 2-11 – Wireless connection on the DAD Fig. 2-12 – Configuration file for wireless connection Once the Notebook Comp uter has been switched on, and the start up button on the DAD unit has been p ressed (a blue indicator light will be continuously lit), op en the K2_FW acquisition software by clickin g on the desktop icon.
IDS Ingegneria Dei Sistemi S.p.A. RIS Hi-Mod - Installation Guide and User Manual Protocol: MN/2009/056 - Rev. 1.0 3. ON LINE ASSISTANCE 3.1 Remote assistance using Webex Support Center Webex Sup p ort Center is a service that allows the activation of a two host session, makin g an ap p lication or the desktop available to the other user or letting y ou cap ture another remote desktop . It can be used to p erform web conferences and p resentations.
IDS Ingegneria Dei Sistemi S.p.A. RIS Hi-Mod - Installation Guide and User Manual Protocol: MN/2009/056 - Rev. 1.0 Once y ou have clicked on the link sent by email, the following window will app ear. Insert y our data into the form (see Fig. 3-2). Fig. 3-2 – Client data insertion form Once y ou have click ed S ubmit, the following p age will ap p ear showing a downloadin g bar. T he session starts as soon as the download is comp lete. (see Fig. 3-3). Fig.
IDS Ingegneria Dei Sistemi S.p.A. RIS Hi-Mod - Installation Guide and User Manual Protocol: MN/2009/056 - Rev. 1.0 As y ou can see fro m the followin g scr een, (Fig. 3-4) y ou are giv en a console, just containin g the Chat, Video and Leave S ession commands. Fig. 3-4 – Welcome to Webex S upport Center window At this p oint, IDS Customer Care can p erform a ran ge of op erations on y our desktop : • Request control of the desktop using the Request Control command.
