- PRO/010/M1 Rev 4 - INGEGNERIA DEI SISTEMI S.p.A. Rev. 1.1 Protocol: MN/2009/056 RIS Hi-Mod / DUALF-400-900 Systems Installation Guide and User Manual RIS Hi-Mod / DUALF-400-900 Installation Guide and User Manual Pisa, November 2010 Tot pag. N°.
IDS Ingegneria Dei Sistemi S.p.A. RIS Hi-Mod / DUALF-400-900 - Installation Guide and User Manual Protocol: MN/2009/056 - Rev. 1.1 Document Evolution Revision Date Reason for change Rev. 1.0 August 2009 First edition Rev. 1.1 November 2010 DUALF-400-900 added OUR CONTACTS IDS Ingegneria dei Sistemi S.p.A. – GeoRadar Division Via Enrica Calabresi, 20 56121 Montacchiello (PISA) - ITALIA Tel: +39.050.3124350 Fax: +39.050.3124205 inforis@ids-spa.it Customer Care department: customercare.gpr@ids-spa.
IDS Ingegneria Dei Sistemi S.p.A. RIS Hi-Mod / DUALF-400-900 - Installation Guide and User Manual Protocol: MN/2009/056 - Rev. 1.1 DISCLAIMER IDS WILL NOT BE HELD RESPONSIBLE FOR THE CONSEQUENCES OF AN IMPROPER USE OF THE EQUIPMENT AND/OR THE SOFTWARE. THIS SOFTWARE MAY INCLUDE AUTOMATED DATA PROCESSING AND ANALYSIS TOOLS.
IDS Ingegneria Dei Sistemi S.p.A. RIS Hi-Mod / DUALF-400-900 - Installation Guide and User Manual Protocol: MN/2009/056 - Rev. 1.1 SAFETY INFORMATION The equipment conforms to the following requirements set by EC regulations, including subsequent modifications, and to the legislation set by the member states that implement these regulations: 1999/05/EEC Radio Directive Warning: this equipment is destined for use in industrial environments (Class A apparatus).
IDS Ingegneria Dei Sistemi S.p.A. RIS Hi-Mod / DUALF-400-900 - Installation Guide and User Manual Protocol: MN/2009/056 - Rev. 1.1 IMPORTANT NOTE FOR THE US CUSTOMERS FCC ID: UFW-HI-MOD This device complies with part 15 of the FCC Rules: Operation is subject to the following conditions: 1. This device may not cause harmful interference, and 2.
IDS Ingegneria Dei Sistemi S.p.A. RIS Hi-Mod / DUALF-400-900 - Installation Guide and User Manual Protocol: MN/2009/056 - Rev. 1.1 IMPORTANT NOTE FOR THE US CUSTOMERS FCC ID: UFW-DUALF-400-900 This device complies with part 15 of the FCC Rules: Operation is subject to the following conditions: 1. This device may not cause harmful interference, and 2.
IDS Ingegneria Dei Sistemi S.p.A. RIS Hi-Mod / DUALF-400-900 - Installation Guide and User Manual ! Protocol: MN/2009/056 - Rev. 1.1 CLEANING INFORMATION WARNING Before cleaning any external parts of the apparatus, make sure that all cables have been disconnected, including the power supply cable. If a damp cloth is used, make sure it is not too wet, to avoid any damage to the electrical components of the equipment. Wait until the equipment is totally dry before reconnecting the cables.
IDS Ingegneria Dei Sistemi S.p.A. RIS Hi-Mod / DUALF-400-900 - Installation Guide and User Manual Protocol: MN/2009/056 - Rev. 1.1 BATTERIES REMOVAL INFORMATION Laptop Batteries: Manufacturer: PANASONIC Type: Li-ion Ni Characteristics: 10.65V 5.7Ah Removal instructions: 1. turn off the laptop; 2. open the drawer with the symbol of the batteries; 3. extract the battery pack pulling the tab.
IDS Ingegneria Dei Sistemi S.p.A. RIS Hi-Mod / DUALF-400-900 - Installation Guide and User Manual Protocol: MN/2009/056 - Rev. 1.1 RECICLYING The crossed out wheeled bin symbol shown on the equipment indicates that the product must be recycled separately from other waste at the end of its useful life. Separate waste disposal of this product at the end of its useful life will be organised and managed by IDS.
IDS Ingegneria Dei Sistemi S.p.A. RIS Hi-Mod / DUALF-400-900 - Installation Guide and User Manual Protocol: MN/2009/056 - Rev. 1.1 WARRANTY CERTIFICATE CONDITIONS 1) IDS Ingegneria dei Sistemi S.p.
IDS Ingegneria Dei Sistemi S.p.A. RIS Hi-Mod / DUALF-400-900 - Installation Guide and User Manual Protocol: MN/2009/056 - Rev. 1.1 INDEX 1. Hardware equipment of the Hi-MOD AND DUALF-400-900 systems ................ 14 1.1 One antenna equipment and configuration ........................................................ 14 Rudder ....................................................................................................................... 14 1.1.1 Assemblage instructions ...........................
IDS Ingegneria Dei Sistemi S.p.A. RIS Hi-Mod / DUALF-400-900 - Installation Guide and User Manual Protocol: MN/2009/056 - Rev. 1.1 FIG. 1-7 – CLOSE UP OF THE METALLIC FRAMES (UP) AND LOCKING DEVICE (DOWN) .................................................................................................................... 18 FIG. 1-8 – INSERTION OF THE ANTENNA AND CLOSE UP OF THE HOOK ........ 18 FIG. 1-9 – INSERTION OF THE DAD CONTROL UNIT AND BATTERY ................ 18 FIG. 1-10 – METRIC WHEEL CABLE ....
IDS Ingegneria Dei Sistemi S.p.A. RIS Hi-Mod / DUALF-400-900 - Installation Guide and User Manual Protocol: MN/2009/056 - Rev. 1.1 FIG. 2-9 – CONNECTING THE DAD CONTROL UNIT TO THE BATTERY PACK AND SWITCHING ON BUTTON (RED COLOR) ................................................. 38 FIG. 2-10 – WIRELESS PORT TO BE ACTIVATED ON CF-19 ..................................39 FIG. 2-11 – WIRELESS CONNECTION ON THE DAD ............................................... 40 FIG.
IDS Ingegneria Dei Sistemi S.p.A. RIS Hi-Mod / DUALF-400-900 - Installation Guide and User Manual Protocol: MN/2009/056 - Rev. 1.1 1. HARDWARE EQUIPMENT OF THE HI-MOD AND DUALF-400-900 SYSTEMS Hi-MOD and DUALF-400-900 systems offers you the possibility to choose up to four different equipments, matching the number of antennas you want to use. This handbook shows you the equipment you will receive and guides you through the configuration of your hardware. One antenna equipment and configuration (Fig.
IDS Ingegneria Dei Sistemi S.p.A. RIS Hi-Mod / DUALF-400-900 - Installation Guide and User Manual Protocol: MN/2009/056 - Rev. 1.1 First you have to set the rudder in its mono antenna setting. The rudder has two free bars and four knobs (Fig. 1-2). The bigger ones must be screwed in vertically to block the free bars in place while the little ones can be screwed in two different position: if placed on the inside part of the frame you will get the mono or three antenna configuration (Fig.
IDS Ingegneria Dei Sistemi S.p.A. RIS Hi-Mod / DUALF-400-900 - Installation Guide and User Manual Protocol: MN/2009/056 - Rev. 1.1 Now you have to build the frame carrying the antenna: you will need the equipment shown in Fig. 1-4. Take one of the wheel frame and screw the two junction pipes in it, then close the frame with the other wheel part (Fig. 1-5). Fig. 1-4 – Antenna frame equipment Fig.
IDS Ingegneria Dei Sistemi S.p.A. RIS Hi-Mod / DUALF-400-900 - Installation Guide and User Manual Protocol: MN/2009/056 - Rev. 1.1 Fig.
IDS Ingegneria Dei Sistemi S.p.A. RIS Hi-Mod / DUALF-400-900 - Installation Guide and User Manual Protocol: MN/2009/056 - Rev. 1.1 Fig. 1-7 – Close up of the metallic frames (up) and locking device (down) Take the antenna and make it slide in the frame from behind. Remember to put and remove the antenna always from the rear part of the frame. When the antenna is in place lock it around the two junction pipes using its four hooks (Fig. 1-8). Fig.
IDS Ingegneria Dei Sistemi S.p.A. RIS Hi-Mod / DUALF-400-900 - Installation Guide and User Manual Protocol: MN/2009/056 - Rev. 1.1 1.1.2 Wiring Once the DAD unit is in place you have to connect it with the metric wheel, the antenna, the battery and your laptop. The metric wheel cable is located on one of the wheel frames. Let it pass through the black strip on the rudder until you reach the first ferrite then link the connector with the Wheel port of the DAD unit (Fig. 1-10). Fig.
IDS Ingegneria Dei Sistemi S.p.A. RIS Hi-Mod / DUALF-400-900 - Installation Guide and User Manual Protocol: MN/2009/056 - Rev. 1.1 Fig. 1-11 – Antenna cable in place Battery cable has two connectors of different shapes in order to help you: one of them must be linked with the battery, the other one with the DAD unit (Fig. 1-12). Fig. 1-12 – Battery cable and LAN cable Fig. 1-12 shows also the LAN cable connector. You have to link the other end of this cable with the LAN port of your laptop.
IDS Ingegneria Dei Sistemi S.p.A. RIS Hi-Mod / DUALF-400-900 - Installation Guide and User Manual Protocol: MN/2009/056 - Rev. 1.1 1.2 Two antennas equipment and configuration Fig. 1-13 shows you the equipment you will receive for your two antennas configuration.
IDS Ingegneria Dei Sistemi S.p.A. RIS Hi-Mod / DUALF-400-900 - Installation Guide and User Manual Protocol: MN/2009/056 - Rev. 1.1 Rudder Antennas Junction Pipes Battery & LAN cables Antenna cables Nonwheeled frame DAD unit & Batteries Fig. 1-13 – Equipment provided for the two antennas configuration 1.2.1 Assemblage instructions First you have to set the rudder in its two antennas setting. The rudder has two free bars and four knobs (Fig. 1-2).
IDS Ingegneria Dei Sistemi S.p.A. RIS Hi-Mod / DUALF-400-900 - Installation Guide and User Manual Protocol: MN/2009/056 - Rev. 1.1 To build the frame carrying the antennas you need the equipment shown in Fig. 1-15. Fig. 1-15 – Two Antennas frame equipment Take one of the wheeled frames and screw two junction pipes in it. Connect these pipes with the non-wheeled frame (the white spots on it show you which side goes down).
IDS Ingegneria Dei Sistemi S.p.A. RIS Hi-Mod / DUALF-400-900 - Installation Guide and User Manual Protocol: MN/2009/056 - Rev. 1.1 Fig. 1-16 – Making the two antennas frame Fig. 1-17 – Insertion and locking of the rudder Take the antennas and make them slide in the frame from behind. Remember to put and remove the antennas always from the rear part of the frame. When the antennas are in place lock them around the four junction pipes using their hooks (Fig. 1-18).
IDS Ingegneria Dei Sistemi S.p.A. RIS Hi-Mod / DUALF-400-900 - Installation Guide and User Manual Protocol: MN/2009/056 - Rev. 1.1 Fig. 1-18 – Insertion of the antennas and close-up of the hook Place the DAD control unit inside the box on the rudder and the batteries in the two little black bags (Fig. 1-19). Fig. 1-19 – DAD unit positioning and Battery bags 1.2.2 Wiring Battery, wheel and LAN cables are linked to the DAD control unit as in the mono antenna configuration (see Par 1.1.
IDS Ingegneria Dei Sistemi S.p.A. RIS Hi-Mod / DUALF-400-900 - Installation Guide and User Manual Protocol: MN/2009/056 - Rev. 1.1 Fig. 1-20 – Antenna cables You can find more info about the DAD unit and its cable connectors in Chapter 2: The DAD control unit.
IDS Ingegneria Dei Sistemi S.p.A. RIS Hi-Mod / DUALF-400-900 - Installation Guide and User Manual Protocol: MN/2009/056 - Rev. 1.1 1.3 Three antennas equipment and configuration Fig. 1-21 shows you the equipment you will receive for your three antennas configuration.
IDS Ingegneria Dei Sistemi S.p.A. RIS Hi-Mod / DUALF-400-900 - Installation Guide and User Manual Protocol: MN/2009/056 - Rev. 1.1 Fig. 1-22 – Side antenna frames parts Take one of the wheeled frames and screw two junction pipes in it. After that close the box using one of the non-wheeled frames as shown in Fig. 1-23. Fig. 1-23 – Side antenna frame Unite the side frame with the central one by linking the metallic locks with the wheels “mushrooms”. Lock up the structure by turning the switches (Fig.
IDS Ingegneria Dei Sistemi S.p.A. RIS Hi-Mod / DUALF-400-900 - Installation Guide and User Manual Protocol: MN/2009/056 - Rev. 1.1 “Mushroom” Locking device Fig. 1-24 – Main frame “mushrooms” & locking device Take the antennas and make them slide in the side frames from behind. Remember to put and remove the antennas always from the rear part of the frames. When the antennas are in place lock them around the junction pipes using their hooks (Fig. 1-25). Fig.
IDS Ingegneria Dei Sistemi S.p.A. RIS Hi-Mod / DUALF-400-900 - Installation Guide and User Manual Protocol: MN/2009/056 - Rev. 1.1 The complete three antenna configuration in shown in Fig. 1-27. Fig. 1-26 – Antenna cables Fig. 1-27 – Three antennas configuration You can find more info about the DAD unit and its cable connectors in Chapter 2: The DAD control unit.
IDS Ingegneria Dei Sistemi S.p.A. RIS Hi-Mod / DUALF-400-900 - Installation Guide and User Manual Protocol: MN/2009/056 - Rev. 1.1 1.4 Four antennas equipment and configuration Fig. 1-28 shows you the equipment you will receive for your four antennas configuration.
IDS Ingegneria Dei Sistemi S.p.A. RIS Hi-Mod / DUALF-400-900 - Installation Guide and User Manual Protocol: MN/2009/056 - Rev. 1.1 1.4.2 Wiring Battery, wheel and LAN cables are linked to the DAD control unit as in the mono antenna configuration (see Par 1.1.2 for further instruction). In the four antennas configuration you have four antenna cables.
IDS Ingegneria Dei Sistemi S.p.A. RIS Hi-Mod / DUALF-400-900 - Installation Guide and User Manual Protocol: MN/2009/056 - Rev. 1.1 Fig. 1-30 – Four antennas configuration You can find more info about the DAD unit and its cable connectors in Chapter 2: The DAD control unit. 2. THE DAD CONTROL UNIT The DAD Control Unit is the control unit responsible for directing the antennas and digitalising the acquired radar data.
IDS Ingegneria Dei Sistemi S.p.A. RIS Hi-Mod / DUALF-400-900 - Installation Guide and User Manual Protocol: MN/2009/056 - Rev. 1.1 Ant1 and Ant 2 Wheel Port Connectors Fig. 2-2 – –DAD side Fast Wave with connections to position sensor and antennae Considering the type of available antenna, the following combinations are possible: 1. Ant.1 (connector with 19 poles) This kind of connector may be connected to the following categories of radar antennae.
IDS Ingegneria Dei Sistemi S.p.A. RIS Hi-Mod / DUALF-400-900 - Installation Guide and User Manual Protocol: MN/2009/056 - Rev. 1.1 Entire range of TR IDS antennae that have an 11 pole connector, if supplied with an appropriate 19-11 pole adaptor (Fig. 2-4). Fig. 2-4 – 19-11 pole Adaptor 2. Ant.
IDS Ingegneria Dei Sistemi S.p.A. RIS Hi-Mod / DUALF-400-900 - Installation Guide and User Manual Protocol: MN/2009/056 - Rev. 1.1 Graphics/Video Memory: Intel 945GM video accelerator with up to 128MB shared video memory Wireless Networking: WLAN 802.11a/b/g, Bluetooth 2.0, Optional WWAN (EVDO, HSDPA) and GPS Ports: Two USB 2.0, Firewire, Ethernet, modem, headphone, mic, docking connector Card Slots: PC Card Type II, SD Card slot Weight: 5 pounds Size: 10.7 x 8.5 x 1.
IDS Ingegneria Dei Sistemi S.p.A. RIS Hi-Mod / DUALF-400-900 - Installation Guide and User Manual Protocol: MN/2009/056 - Rev. 1.1 Fig. 2-6 – Lan Cable Fig. 2-7 – Lan Cable connection between the Notebook Computer and the DAD Control Unit Connect the DAD Control Unit to the Battery using the Battery Cable (Fig. 2-8) as shown in (Fig. 2-9) Fig.
IDS Ingegneria Dei Sistemi S.p.A. RIS Hi-Mod / DUALF-400-900 - Installation Guide and User Manual Protocol: MN/2009/056 - Rev. 1.1 Fig. 2-9 – Connecting the DAD Control Unit to the battery pack and switching on button (red color) Press the red button to switch on the DAD control unit (Fig. 2-9). This button has to be kept pressed until the blue on switch lights up. If the K2_FW software is not activated within 30 seconds, the indicator light will start to flash.
IDS Ingegneria Dei Sistemi S.p.A. RIS Hi-Mod / DUALF-400-900 - Installation Guide and User Manual Protocol: MN/2009/056 - Rev. 1.1 2.3 Wireless connection Here below you can see the requirements and steps to connect by wireless DAD to PC: 1) System requirement: wireless network board of PC must support network protocol type 802.11g. 2) Disconnect Lan cable from DAD and from PC. 3) Connect the wireless plug on LAN port of the DAD (Fig. 2-1 e Fig. 2-11).
IDS Ingegneria Dei Sistemi S.p.A. RIS Hi-Mod / DUALF-400-900 - Installation Guide and User Manual Protocol: MN/2009/056 - Rev. 1.1 Fig. 2-11 – Wireless connection on the DAD Fig. 2-12 – Configuration file for wireless connection Once the Notebook Computer has been switched on, and the start up button on the DAD unit has been pressed (a blue indicator light will be continuously lit), open the K2_FW acquisition software by clicking on the desktop icon.
IDS Ingegneria Dei Sistemi S.p.A. RIS Hi-Mod / DUALF-400-900 - Installation Guide and User Manual 41 / 45 Protocol: MN/2009/056 - Rev. 1.
IDS Ingegneria Dei Sistemi S.p.A. RIS Hi-Mod / DUALF-400-900 - Installation Guide and User Manual Protocol: MN/2009/056 - Rev. 1.1 3. ON LINE ASSISTANCE 3.1 Remote assistance using Webex Support Center Webex Support Center is a service that allows the activation of a two host session, making an application or the desktop available to the other user or letting you capture another remote desktop. It can be used to perform web conferences and presentations.
IDS Ingegneria Dei Sistemi S.p.A. RIS Hi-Mod / DUALF-400-900 - Installation Guide and User Manual Protocol: MN/2009/056 - Rev. 1.1 Once you have clicked on the link sent by email, the following window will appear. Insert your data into the form (see Fig. 3-2). Fig. 3-2 – Client data insertion form Once you have clicked Submit, the following page will appear showing a downloading bar. The session starts as soon as the download is complete. (see Fig. 3-3).
IDS Ingegneria Dei Sistemi S.p.A. RIS Hi-Mod / DUALF-400-900 - Installation Guide and User Manual Protocol: MN/2009/056 - Rev. 1.1 Fig. 3-3 – Webex Set up window As you can see from the following screen, (Fig. 3-4) you are given a console, just containing the Chat, Video and Leave Session commands. Fig. 3-4 – Welcome to Webex Support Center window At this point, IDS Customer Care can perform a range of operations on your desktop: Request control of the desktop using the Request Control command.
IDS Ingegneria Dei Sistemi S.p.A. RIS Hi-Mod / DUALF-400-900 - Installation Guide and User Manual Protocol: MN/2009/056 - Rev. 1.1 Fig.
