User Manual 1
Table of Contents 1. 1.1 Introduction..................................................................................................................... 8 Printer outside features ........................................................................................................ 8 1.2. Printer inside features ............................................................................................................ 11 1.3 Ribbon cartridge features..................................................
5.2. Contactless smartcard reader .............................................................................................. 57 6. Troubleshooting ................................................................................................................60 6.1. Error Message ......................................................................................................................... 60 6.2. Cleaning the printer ...........................................................................
Table of Figures Figure 1 CP55 front features ............................................................................................................................... 8 Figure 2 CP55 rear features ................................................................................................................................. 9 Figure 3 CP55-S (Standard) .................................................................................................................................
Figure 22 Loading the cards 2 .......................................................................................................................... 19 Figure 23 Loading the cards 3 .......................................................................................................................... 19 Figure 24 Loading the cards 4 .......................................................................................................................... 19 Figure 25 CP55 Withdrawal a card ...........
Figure 49 Advanced ............................................................................................................................................... 34 Figure 50 Color Management ............................................................................................................................ 34 Figure 51 Security ................................................................................................................................................... 35 Figure 52 Service ...
Figure 76 OCP configuration............................................................................................................................. 52 Figure 77 Network user configuration.......................................................................................................... 53 Figure 78 Contact smartcard reader driver installation ...................................................................... 54 Figure 79 License agreement......................................................
1. Introduction 1.1 Printer outside features For the user’s convenience, CP55 printer status can be seen through LCD with LED and the printer can be controlled by two LED buttons. It takes a power via the 24V adaptor provided with the printer. Using USB and Network port, it is communicated with the user’s PC. The following shows the outside functional features found on the printer.
⑥ Network port In case there is no network option, it is closed. ⑦⑧⑨⑩ ⑦ USB port ⑧ 24V power connector ⑨ Power switch ⑩ Kensington Lock ⑥ Figure 2 CP55 rear features There are two models in CP55 card printer series such as CP55, CP55 Dual. CP55 (Figure.3) is the standard card printer. It can be printed in single side with the encoding. This manual is prepared based on CP55. CP55 Dual (Figure.4) has a flipper which can enable to print in both sides.
Figure 4 CP55-D (Dual) 10
1.2. Printer inside features In CP55 printer, the ribbon is installed by a ribbon cartridge which can be used semi permanently. The following shows the inside functional features found on your CP55 printer. ⑤ ④ ② ③ ① Figure 5 CP55 Inside features ① Output hopper(Stacker) Collect the printed card and/or encoded cards. Maximum 40 cards are loaded and the extra printed/encoded card is passed out. It can be withdrawed when pulling forward. ② Input hopper Load the cards for printing.
1.3 Ribbon cartridge features CP55 printer uses the ribbon cartridge as below picture. ② ③ ④ ① ① Ribbon cartridge ② Take up parts ③ Supply parts ④ Disposable Cleaning Roller Figure 6 Ribbon cartridge features ① Ribbon cartridge -. Install a ribbon and a disposable cleaning roller provided with the ribbon. -. This semi-permanent ribbon cartridge is a component of the printer. Printer does not operate if it is broken or damaged. In this case, please contact printer reseller.
1.4 Display and Buttons Control panel of Printer consists of 2 lines LCD and 2 buttons. The 2 buttons have the functions as shown in the Figure 7. The main LCD message of CP55 printer is ‘HEIDI CP55-S’. On the other hand, CP55 Dual printer is ‘HEIDI CP55-D’. Left Button Right Button Two Line LCD Figure 7 CP55-S & CP55-D Display and Buttons The status of CP55 is ‘Initializing’ when boot up. It is changed to ‘System Ready’ if the printer is fine. It is change to ‘Printing’ when the printer is working.
2. Printer installation 2.1. Connecting a power and a USB cable Connect the power and USB cable as the below picture. Please refer to the ‘Network Configuration’ if you use the LAN connection.
2.2. Fitting the ribbon Before printing, prepare the related items such as a card, a ribbon and a cleaning roller. In this section we invite you to know the proper method of installing the ribbon and the cleaning roller into the printer. (1) Turn off the printer (2) Open the printer top cover by pressing the top cover open button. Figure 10 Top Cover open (3) Take out the ribbon cartridge.
(4) Install a ribbon into the ribbon cartridge as the right picture. Figure 12 Loading the ribbon 1 (5) Insert the supply side of the ribbon to no.1 hole and press the opposite (no.2). Insert the take-up side of the ribbon same method to no.3 and no.4. After inserting, tighten the ribbon. ① (Caution! If the ribbon is not tightened, a rolling up error might be happened.) ③ ② ④ Figure 13 Loading the ribbon 2 (6) Install the disposable cleaning roller to the ribbon cartridge.
(7) Peel the protective wrapper from the cleaning roller. After removing the protective wrapper, the cleaning roller should be kept clean from fingerprints, dust and foreign substances to avoid contamination because it is adhesive. (Caution! Do not use without peeling off the protective wrapper because the cleaning roller cannot perform its function.
2.3. Loading the cards This section shows how to load the plastic cards. (1) Open the input hopper cover. Adjust the card thickness with the card thickness control lever. (Caution! If the adjustment is not correct, it will make some error. Use the type of cards in the specification of this manual. Always keep the card surface clean state.) Figure 18 Adjusting the card thickness lever (2) To separate cards from each other, push a stack of cards back and forth to an angle about 45 degrees vertically.
(3) Stand the stack of cards vertically after separating Figure 21 Loading the cards 1 (4) Load the cards on the input hopper properly and close the hopper cover. Figure 22 Loading the cards 2 (5) When insert each one card, insert the card to the end as left picture (Caution! If the printer has a lock device, a card can’t be inserted one by one. You can select the ‘lock device’ option when you order the printer. It can lock the top cover and hopper to prevent extracting the ribbon and cards without key.
2.4. The withdrawal of printed cards. Printed cards are passed out to the stacker of front bottom side of CP55 printer. Figure 25 CP55 Withdrawal a card CP55’s stacker can be divided as following image. so you can withdraw the printed cards easily.
2.5. Rear Stacker (Option) CP55 can install a rear stacker for option at the back of the printer. In case of CP55, please install into the slots at the backside. In case of CP55 Dual, please open the back cover of the printer and install it. Figure 26 CP55 installation of Rear Stacker Figure 27 CP55 Dual installation of Rear Stacker After that, set the value of ‘Card Out’ to ‘Back’ in the Configuration Program.
2.6. Driver installation (Windows 7 / 8 / 10) (1) Please insert the installation CD. Please choose language and click “Driver Install”. Figure 29 Install printer driver 1 (2) When “User Account Control” window is opened, click “Yes” Figure 30 Install printer driver 2 (3) STEP 1: Please turn off printer if it is connected to PC. Please click “Next”. When you click “Next”, older driver will be removed automatically. This process will take several minutes to remove older driver.
(4) STEP 2: When you click “Next”, the driver installation will be ready. Figure 32 Install printer driver 4 (5) STEP 3: - USB Please click “Next” if printer is connected to USB only. If you want to install the driver for a printer connected to network, please select the “TCP/IP Network port” and select the proper printer as step (7). Figure 33 Install printer driver 5 (6) Please turn on the printer (Network cable is not supplied. Please ask network administrator for more questions.
(8) When driver installation is completed, please click “Close” Figure 36 Install printer driver 8 (9) Please open “Devices and Printers” from “Hardware and Sound”. Please check if “Heidi CP55 Card Printer” is created. Figure 37 Install printer driver 9 (10) Please click the right mouse button after cursor is placed on “Heidi CP55 Card Printer” icon. Click “Printer properties”.
(11) Please select “general” tab and click “Print test page” in “Heidi CP55 Card Printer Properties” window. Figure 39 Install printer driver 11 (12) Please check test card if it is printed properly and click “Close” if a card is printed properly. (If card is not printed or error comes out, please refer to “Trouble Shooting”.
3. Driver configuration 3.1. Printer Properties To check printer properties, you need to open printer driver. Please open “Devices and Printers” and right-click “Heidi CP55 Card Printer”. Click “Printer Properties”. (1) Printing Preferences Please click “Preferences…” shown on the bottom of the left picture. Figure 41 Printer properties (2) Layout - You can select either horizontal or vertical printing direction. To apply your selection, click “OK”.
(3) Input / Output [ Supply Tray ] Supply : You can select “Auto” if CP55 has 1 input hopper. Please select the hopper if it has a multi hopper. Tray : You can select “CR-80” because CP55 supports CR80 cards only. Figure 43 Input / Output (4) Printing Do Printing : You can select printing or not [ Print Side ] Side : Please select one side printing or both sides printing (It is possible only when you have a flipper.) [ Front / Back ] Color : You can select color or mono print.
Partial : Partial print mode. It is printed partially for the print area only. Printing speed can be faster than standard mode. Dither : There are 3 possible selections, Threshold, Random, and Diffusion Dither. It is performed with K and KO ribbon only. (Please select “Diffusion Dither” for high quality.) Ribbon Save : Select the split function or not when K ribbon is installed K ribbon Split : You can set the both sides (Front:YMCO, Back:K) to save color ribbon(YMCKO, HYMCKO, BYMCKO).
Track 1 : (default) IATA Track 2 : (default) ABA Track 3 : (default) MINS JIS II Track : (default) JIS II Density: MS encoding density (210, 75) Text Encoding Sentinels : Start, End Marker for text magnetic encoding Start : Start Marker End : End Marker 29
3.2. Advanced Options To change the detailed configuration, In the ‘Layout’ tab shown, Please click “Advanced…” shown on the bottom of the ‘Layout’ tab of the ‘Preferences’. Reset Default Values: Reset to default. Color Correction: You can correct gamma for colors. You need to use CardPrinterConfig to adjust color densities.
Black Object: to extract resin black automatically for text, line, box, circle, binary images, etc. Black Text: to extract resin black for text only Black Dots: to extract resin black for all of black Black Dots only: to extract resin black for all of black and not to print on color panels Not Use: not to extract resin black Extra Controls : Other options - Fast Alignment [On/Off]: to set the position of input card to the magnetic encoder or normal printing.
Wait Position [-100:100]: to set the position of card to wait from the criteria position. Unit is 0.1mm Wait Time [0:1000]: to set time to wait.
3.3. Other settings (1) Sharing You can share a printer with Sharing tab via Network. Default is unchecked “Share this printer”. Figure 47 Printer sharing (2) Ports Port tab shows which port is connected with CP55. CP55 has connection with USB Virtual printer port as left picture because CP55 uses USB connected to PC. (Caution! This port is selected automatically. It is recommended to maintain default.
(3) Advanced It is available for Working Time setting, Priority order, Spool print etc. in “Advanced” tab. “Advanced” setting follows MS Windows standard. If you want to change the setting, please refer to the Window manual. (It is recommended to maintain default.) Figure 49 Advanced (4) Color Management In “Color management” tab, you can select color management profile fit to the printer. CP55 uses color profile to express optimal color. The driver selects color profile automatically to fit each ribbon.
(5) Security You can set the permission to use a printer. Depend on the permission, the certain group or user can print, manage the printer/documents or not. Figure 51 Security (6) Service You can recognize the modules to connect, printer serial, printer ID, driver version, firmware version, type of ribbon & balance and printer’s status. You can print the “technical support sheet” on a card to check printer’s setup value.
4. Utilities 4.1. Card Printer Config CP55 is produced with optimized setting. You need to adjust setting value if required or spare parts are replaced using CardPrinterConfig in our Installation CD. You can adjust following settings with CardPrinterConfig. (1) Run CardPrinterConfig Password input window is displayed when you run this program. If you input the correct password, the recorded setup value will be shown and you can change values. The password is saved to CP55 printer.
(2) Card Printer Basic Setup ② ① ③ ④ ⑤ ⑥ ⑨ ⑦ ⑧ ⑩ Figure 55 CardPrinterConfig – Card Printer Basic Setup ① To show connected printers Device: You can select a printer using pull-down menu. “HEIDI CP55 Card Printer” is a name of printer. “CP55” is printer ID, “USB005” is connected port. If you connect the Network printer, please check the “Allow Network Printer” and select in the pull-down menu. ② To set administrator password and user password. Change Root PW: To set administrator (root) password.
③ Click “Card Printer” tab.(If flipper is installed, you can setup flipper setting value by “Flipper” tab.. ④ To show firmware version, serial number of printer and serial number, resister & type of print head. ⑤ To show print area. It shows exaggeratingly for user convenience. ⑥ To set print area. Please set it properly to print on an entire card because CP55 is a direct thermal card printer. When you click “⑦ Print”, a card is printed as like “④ example”.
Figure 56 Color density Black Density: To set resin black density. In the picture, barcode is printed to express density. When density is too strong, barcode is printed too thick. When density is too weak, barcode is too thin. Please adjust resin black density to express clear barcode. Please refer to the following pictures. Figure 57 Resin Black density Overlay Density: To set overlay density. Please set it when overlay is printed on surface regularly.
Figure 58 Overlay density ⑧ To print calibration card. ⑨ To show advanced Setup. (It is recommended not to set advanced setup.) ⑩ To load or save values. Get Config.: to get values from current printer Set Config. : to set values to current printer Load from File: to load values from file Save to File : to save values to file Load Default : to load default. Please adjust values again after load default.
(3) Card Printer Advanced Setup You can set more values. ① ② ③ ④ Figure 59 CardPrinterConfig – Card Printer Advanced Setup ① You can set Printer ID, PC serial, Print head and Magnetic encryption key. Change Printer ID: When CP55 is used by SDK, you can set unique ID for CP55 printer regardless of whether it is connected by USB or what IP address is. It is useful to connect and use several printers. Default is “CP55”. Set PC Serial: One of security function. You can use a printer with specific PC.
Set Mag. Encrypt Key: One of security function. When you use SDK, you can encrypt magnetic stripe encoding data transmitted by USB. You can define and save the encryption key to CP55 using “Set Mag. Encrypt Key”. ② To show how many cards are issued with CP55 printer. “Total Issue Count” is the number of issued cards from factory shipment, “User Issue Count” is the number of issued cards from replacing head. When you replace a head, please initialize the number by ticking “Reset User Issue Count”.
SBS Only: Please enable it when you issue cards with software programed by SDK. This option disables printer device driver. Safe Head Heat: Set not to print if the print head is overheated. Cleaning Warning: Set to show the ‘Do cleaning’ message periodically Use USB Serial: When CP55 is connected to USB, it transmits the USB serial number to PC. Default is the same number used by all CP55. Please set this option when you use multiple CP55 printers connected to 1 PC via USB.
(4) Flipper Setup This ‘Flipper’ tab is shown when the flipper option is installed.
4.2. Network configuration (1) Connecting network port The printer which installed with network option has a port for network connection as shown in the left picture. ① Network Port ② USB port ① ② ③ ④ ③ Power Supply Connector ④ Power Switch Figure 61 Rear view of CP55 printer 1 Please connect network cable (RJ45) to a printer. (Network cable is not supplied. Please ask network administrator for more questions.) Figure 62 Rear view of CP55 printer 2 Please run NetAdmin.
(2) Network configuration NetAdmin is run as the Pic.72 after turning on CP55 network printer. ① Printer Connection Status Searches local network, finds and shows available network printer. ① ② ③ ② Network Module Management Searches connected encoder on network module. Reboots, Resets network module. Firmware upgrade available ③ Printer Configuration Sets detailed system configuration.
If you are unable to find printer in local network, please connect printer by USB. You can setup network by USB. When you click Refresh, you can find a printer connected by USB as shown in the left picture.. You don’t need to install device driver for network configuration by USB. Please ignore messages related to device installation. You can change values of “System Management” only when you connect a printer by USB. Please connect a printer by network to use all of the functions of Netadmin.exe.
“USB port state” shows USB device status connected on network module. Network module has 4 USB ports. Network module supports PC/SC. When you install the encoders that support PC/SC on network module, you can recognize the status of encoders. Figure 67 USB port state “Reboot module” reboots network module. Please click “Yes” when pop-up window comes out for reboot. It takes 1 minute to reboot. Please click “Refresh” after reboot.
“Reset to default” resets to default and reboot network module. Please click “Yes” when pop-up window comes out for reset. It takes 1 minute to reboot. Please click “Refresh” after reboot. When proper printer shown, please connect printer by clicking “Connect”. Figure 69 Reset to default “Upgrade firmware” enables to upgrade firmware of network module. You can choose a firmware file.
Warning box will be shown during firmware upgrade for network module. It is recommended not to do other work during firmware upgrade for system reliability. Please do not turn off a printer until the upgrade is completed. Figure 71 Upgrading the firmware 2 When firmware upgrade is completed, pop-up comes out for reboot. Please click “Yes”. It takes 1 minute to reboot. Please click “Refresh” after reboot. When proper printer shown, please connect printer by clicking “Connect”.
If you setup network automatically, please choose DHCP. Please select DHCP or Static. “DHCP” is default for CP55 printer. Please enter values for “IP”, “Network Mask”, and “Gateway”. Click “Set Configuration”. Static IP is recommended. DHCP server assigns IP address automatically but this IP address is temporary, so the IP address may be changed. In this case, the network error may occur in connecting to CP55 network printer.
You can change Service Configuration. CP55 network printer provides 3 kinds of service (change “USB Spool”, “Network Spool” and “Network SDK”). You can select and change the service according to the need. In “Network SDK”, you can control the printer and print a card well, and the printer supports SSL (Secure Sockets Layer) and User Authentication for security. Please use default and ask technician for details. Figure 75 Network service configuration You can use Open Card Print function.
You can add, change, delete User and change its password. “admin” is administrator and you can’t delete this account.
5. Optional device driver installation In CP55 printer, you can install the optional devices that encode contact smartcard or contactless smartcard. If your purchased CP55 printer has optional devices, you should also install the smart card reader drivers. 5.1. Contact smartcard reader In CP55 printer, you can install the two types of optional devices which are contact smartcard reader and mobile SIM smartcard reader.
(2) License agreement The license agreement window is shown. Check at the agreement and click “Next”. Figure 79 License agreement (3) Installation The installation message is shown as the picture. Click “Install” to install driver.
(4) Complete installation When the installation is completed, the window is shown. Click the “Finish” to complete the installation steps.
5.2. Contactless smartcard reader In CP55 printer, you can install the two types of smartcard reader which are internal contactless smartcard reader and external contactless smartcard reader. If you have one or more contactless smartcard reader devices on your printer, you should install the contactless smartcard device driver as in the following, and connect CP55 printer to your PC.
(2) Choose the installation method At the window as the picture, select “Install from a list or specific location” and click “Next”. Figure 83 Installation method selection (3) Driver location Insert the smartcard installation CD and find “\Options\ Omnikey 5121” directory on your CD. Find the right directory which is installed OS version on your PC, and select the directory as the picture, and click “Next”.
(4) Complete installation When the installation is completed, the window as the Figure 58 is shown, click “Finish” to complete the installation steps.
6. Troubleshooting 6.1. Error Message CP55 printer shows the error message in the LCD display when it occurs. Click the Left button to retry or the right button to cancel an operation. The following shows the error message on your CP55 Printer. For checking a status of printer, please use a CardPrinterTest or CardPrinterDiagnostics in the Utilities folder of Install CD. No LCD Message Description and Countermeasures Fail to move a card from the hopper to the printer inside. -.
No LCD Message Description and Countermeasures The printer can’t search the ribbon panel in printing or booting up -. Check the operating state of the Ribbon Motor 7 Ribbon Seek Err -. Check the operating state of the ribbon encoder sensor and gears -. Check and clean the Color In/Out Sensor -. Check the operating state of the color in/out Sensor The printer can’t wind the ribbon in printing or booting up. 8 Ribbon Move Err -. Check the operating state of the Ribbon Motor -.
No LCD Message Description and Countermeasures Error occurs while initializing 14 Init Error -. Check the status of installation of ribbon Fail to communicate between a printer and a flipper 15 DeviceCon Error -. Check a cable between a printer and a flipper 16 N/A Error occurs while operating a flipper 17 Flipper Error -. Remove a card after opening a flipper cover -. Check the card size All ribbons are used 18 Ribbon Zero -.
Failed to execute a command of the printer -. Replace the USB cable USB 24 SetCommandFail -. Change the USB port in the PC -. Turn off/on the printer The printing data is full in the spooler 25 Spool Full -. This message disappear after printing all data to send -.
6.2. Cleaning the printer To maintain the best condition of CP55 printer, you must clean the printer periodically. If you use the exclusive cleaning card as the picture, you can clean the printer easily. For purchase the exclusive cleaning card, ask to CP55 printer provider. Figure 86 Exclusive cleaning card for CP55 printer If the exclusive cleaning card is ready, click the “Clean Printer” in the service tab of CP55 printer driver. After click, Clean Printer program to clean the printer is run.
Step 1. Connect the CP55 printer to PC and turn it on, and prepare the exclusive cleaning card. Figure 88 Printer cleaning Step 1 Step 2. Open the hopper and top cover and remove the card and ribbon cartridge.
Step 3. Insert the exclusive cleaning card into the printer through input hopper. When the exclusive cleaning card is inserted to the cleaning roller, it will be move automatically. It is normal that the exclusive cleaning card is inserted to the ends and rollers are moving to clean. Figure 90 Printer cleaning Step 3 Step 4. Close the top cover to clean the Thermal Print Head and the printing roller. When the top cover is closed, cleaning card will be moving back and forth to clean.
Step 5. Wait until the cleaning is completed. When the cleaning is completed, the exclusive cleaning card will be ejected automatically as the picture. Figure 92 Printer cleaning Step 5 Step 6. Remove the exclusive cleaning card and install ribbon cartridge into the printer.
6.3. TPH (Thermal Print Head) replacement 1. Check the serial number and the resistance of new Thermal Print Head as the Figure. TPH type: A = KEE, B = KPE Serial No.: see the red box. TPH resistance: see the green box. Figure 94 Thermal Print Head 2. Set up the new TPH’s configuration using CardPrinterSetup program. Step1: Run ‘Card Printer Setup’ in Utilities of the installation CD and click expansion button. Step2: Click “Change Header” in the extended setup. Step3: Input the TPH’s Serial No.
3. Replacing the new TPH Step1: Remove the old TPH from the top cover. (1) Turn off the printer and open the top cover. (2) Hold the TPH and press the locked hook, then the TPH is disconnected.. (3) Disconnect the TPH from print head wire carefully. (Caution: TPH is possible to HOT.) Step2: Installing the new TPH (1) Connect new TPH to the print head wire. (2). Put the new TPH on the Shift and pull it up until be locked.. Figure 96 Print head replacement 4. Setup the print position and the color density.
6.4. Card movement 6.4.1. Cards can’t enter into the printer from input hopper. Non-standard cards or bad cards. Change the cards. You can use only ISO CR-80 card (54mm x 86mm). Card thickness control lever is set improperly. Regulate the card thickness control lever to fit the current card thickness. Bad card array. Array the cards again and put them on input hopper as section 2.2 in this manual. Cards have static and moisture. Remove the moisture or static. 6.4.2.
Printer setting is changed or is not proper. Please contact the local supplier. The transfer roller or the printing roller is contaminated with the dust and dirt. Remove the dust and dirt with the cleaning kit as section 6.1. The card surface is contaminated with the dust and dirt. Check the card surface and remove the dust and dirt and try again. If this problem occurs again, retry with new card. 6.5. Printing quality 6.5.1. Not printed or wrong colors printed spot.
6.5.3. Unclear or not uniform print. Uneven or bad card surface. Change the card. Too high or low setting of the color density. Please contact the local supplier. The color density default of your printer needs to be changed. The printer head is contaminated with the dust and dirt. Clean the printer head with cleaning kit. Figure 100 Printing quality trouble 3 6.5.4. Not aligned color print. Non-standard cards or bad cards. Change the cards. You can use only ISO CR80 card (54mm x 86mm).
6.6. Magnetic stripe encoding 6.6.1. Magnetic encoding error. First of all, Please press left LED button to retry. The magnetic head is contaminated with the dust and dirt. Clean the magnetic head with the cleaning kit. The magnetic encoding data is not transmitted or the wrong data is transmitted. Check the setting of the program and the driver and the magnetic encoding data you transmitted. The card is not magnetic card, or inserting direction is wrong. Change the card or the direction.
Ribbon is consumed. Printing is not possible if ribbon is used up. Change the ribbon. Snapped ribbon. Open the top cover and take out the cartridge. After putting the snapped pieces on together, install the cartridge again. 6.7.3. Printer doesn’t operate even if the printing data has been transmitted. Check the following. Printer power off. Check the power. Turn on the printer power. Check the printer adaptor whether it is connected with a socket and the printer. Bad power adaptor.
7. Specification Model Printing CP55-S Print Type Direct to card dye-sublimation/resin thermal transfer Print Area Edge to Edge Resolution 300dpi Dual Side Printing Card Option (with Flipper) Automatic Card Size ISO CR80 Card Type Capacity 0.38mm (15mil), 1.0mm (40mil) PVC, Any cards with dye-receiving layer(PET, Composite PVC, PC) Monochrome 4.5 sec./card (800 cards/hour) YMCKO 21 sec.
RFID(13.56MHz) Usage The RFID Tag is used for the security and the recognition of the ribbon. To get the optimized printing quality on the printed card, the genuine ribbon of IDP should be used to print cards by using SMART printer. SMART printer can recognize the genuine ribbon by reading the encoded information on the RFID Tag of the ribbons.
